Foscam C1 HI3518E no ethernet after factory Reset

Cju

n3wb
Joined
Nov 2, 2019
Messages
1
Reaction score
0
Location
Germany
The first, sorry for my realy bad english.

I have a Foscam C1 IP camera (HI3518E), after a factory reset the ethernet don't work anymore.
After stopping U-Boot manually, the correct edition should actually look like this. (WiFi works)


U-Boot 2010.06 (Dec 11 2014 - 15:55:58)

Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
MMC: MMC FLASH INIT: No card on slot!
In: serial
Out: serial
Err: serial
Auto-update from SD Card:
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Can't find sd card device!
Can't load upgrade file, aborting sd -update
Auto-update from TFTP: trying update file 'recover_image.bin'
Hisilicon ETH net controler
MAC: 00-00-23-34-45-66
UP_PORT : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M
TFTP from server 192.168.233.233; our IP address is 192.168.233.2
Download Filename 'recover_image.bin'.
Download to address: 0x82000000
Downloading: *T T T
Retry count exceeded; starting again
Can't load update file, aborting auto-update
Hit any key to stop autoboot: 1 0




but she looks like this...no ethernet



Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
MMC: MMC FLASH INIT: No card on slot!
In: serial
Out: serial
Err: serial
Auto-update from SD Card:
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Can't find sd card device!
Can't load upgrade file, aborting sd -update
Auto-update from TFTP: trying update file 'recover_image.bin'
Hisilicon ETH net controler
MAC: 00-00-23-34-45-66
Up/Down PHY not link.
Can't load update file, aborting auto-update
Hit any key to stop autoboot: 1


the answer of a ping from Hisilicon

hisilicon # ping 192.168.233.233
Hisilicon ETH net controler
miiphy_register: non unique device name '0:1'
miiphy_register: non unique device name '0:2'
MAC: 00-00-23-34-45-66
Up/Down PHY not link.
ping failed; host 192.168.233.233 is not alive


the answer to printenv from Hisilicon

hisilicon # printenv
bootdelay=1
baudrate=115200
ethaddr=00:00:23:34:45:66
bootfile="uImage"
mdio_intf=mii
filesize=28540
fileaddr=82000000
bootcmd=sf probe 0;sf read 0x82000000 0x80000 0x300000;go 0x82000000
serverip=192.168.233.233
ipaddr=192.168.233.2
gatewayip=192.168.233.1
netmask=255.255.255.0
updatefile=recover_image.bin
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06 (Dec 11 2014 - 15:55:58)
Environment size: 403/262140 bytes
hisilicon #

the answer to mii dump from Hisilicon

hisilicon # mii dump 0 0
0. (ffff) -- PHY control register --
(8000:8000) 0.15 = 1 reset
(4000:4000) 0.14 = 1 loopback
(2040:2040) 0. 6,13 = b11 speed selection = ??? Mbps
(1000:1000) 0.12 = 1 A/N enable
(0800:0800) 0.11 = 1 power-down
(0400:0400) 0.10 = 1 isolate
(0200:0200) 0. 9 = 1 restart A/N
(0100:0100) 0. 8 = 1 duplex = full
(0080:0080) 0. 7 = 1 collision test enable
(003f:003f) 0. 5- 0 = 63 (reserved)

hisilicon # mii dump 0 1
1. (ffff) -- PHY status register --
(8000:8000) 1.15 = 1 100BASE-T4 able
(4000:4000) 1.14 = 1 100BASE-X full duplex able
(2000:2000) 1.13 = 1 100BASE-X half duplex able
(1000:1000) 1.12 = 1 10 Mbps full duplex able
(0800:0800) 1.11 = 1 10 Mbps half duplex able
(0400:0400) 1.10 = 1 100BASE-T2 full duplex able
(0200:0200) 1. 9 = 1 100BASE-T2 half duplex able
(0100:0100) 1. 8 = 1 extended status
(0080:0080) 1. 7 = 1 (reserved)
(0040:0040) 1. 6 = 1 MF preamble suppression
(0020:0020) 1. 5 = 1 A/N complete
(0010:0010) 1. 4 = 1 remote fault
(0008:0008) 1. 3 = 1 A/N able
(0004:0004) 1. 2 = 1 link status
(0002:0002) 1. 1 = 1 jabber detect
(0001:0001) 1. 0 = 1 extended capabilities


Can anyone fix the Problem ? and help me ?
 
Last edited:
Top