Menu
What's new

Camera great during day - awful at night

bertsirkin

bertsirkin

Getting the hang of it
Joined
Dec 14, 2015
Messages
123
Reaction score
16
I have a Hikvision DS-2CD2132F-I. When I first installed it about 2 years ago, it worked great, night and day. at some point, it started to get hazy at night. I recently replaced it with a newer IP cam, and it's fine in the exact same location. I cleaned the older cam inside and out, and installed it in a new place, but, it's just as bad. It's fine when it first switches to IR and there's still some ambient light outside, but once it gets fully dark, it looks like the attached image.

Any ideas why it gets so hazy at night?
 

Attachments

mat200

mat200

IPCT Contributor
Joined
Jan 17, 2017
Messages
13,894
Reaction score
23,183
Gul-Dukat said:
IR reflection?
Click to expand...
bertsirkin said:
I have a Hikvision DS-2CD2132F-I...
Any ideas why it gets so hazy at night?
Click to expand...
updated:

Hi bertsirkin ,

Sounds like Gui-Dukat is on to a possible suspect. As it is a dome perhaps the foam ( ring around the lens ) inside the dome has decayed over time and is now letting IR light into the lens at night?
 
Last edited:
bertsirkin

bertsirkin

Getting the hang of it
Joined
Dec 14, 2015
Messages
123
Reaction score
16
mat200 said:
Hi Gui-Dukat,
Sounds like bertsirkin is on to a possible suspect. As it is a dome perhaps the foam inside the dome has decayed over time and is now letting IR light into the lens at night?
Click to expand...
What foam is inside? I don't remember seeing anything inside the dome that didn't look good. There's a lens/IR unit mounted on a circuit board with a dome over it - I don't remember seeing anything that looked like foam.

I don't think It's IR reflection from outside the unit. I replaced this cam in the same place with a new one, and it's fine. This older cam is doing the same thing in both places. So, whatever it is, has something to do with this cam.
 
M

Mr_D

Getting comfortable
Joined
Nov 17, 2017
Messages
596
Reaction score
527
Location
Southern California
It could even be a simple misalignment of the foam. When I opened my Dahua eyeball to install an SD card, the foam ring around the lens got pushed back a little during re-assembly. I had to open it again and slide the foam out until it was almost falling off the cylinder around the lens before it would make contact with the piece of glass on the front of the eyeball.
 
A

aristobrat

IPCT Contributor
Joined
Dec 5, 2016
Messages
2,983
Reaction score
3,180
Yup, that was pretty much what the Hikvision support doc above demonstrates (and also why domes are my least preferred styles)! :)
 
bertsirkin

bertsirkin

Getting the hang of it
Joined
Dec 14, 2015
Messages
123
Reaction score
16
aristobrat said:
https://www.hikvision.com/ueditor/net/upload/2015-06-10/99361bb6-27d5-482a-aaf3-2cdc32f835d1.pdf
Click to expand...
Mr_D said:
It could even be a simple misalignment of the foam. When I opened my Dahua eyeball to install an SD card, the foam ring around the lens got pushed back a little during re-assembly. I had to open it again and slide the foam out until it was almost falling off the cylinder around the lens before it would make contact with the piece of glass on the front of the eyeball.
Click to expand...
aristobrat said:
Yup, that was pretty much what the Hikvision support doc above demonstrates (and also why domes are my least preferred styles)! :)
Click to expand...
The foam ring seems to be the issue. I'll have to climb the ladder again to see if I can re-position it, or maybe replace it with some black foam, if I can find some.

Thanks aristobrat & Mr_D - I'll let you know what happens once I get back up to the camera.
 
bertsirkin

bertsirkin

Getting the hang of it
Joined
Dec 14, 2015
Messages
123
Reaction score
16
I got back up on the ladder and pulled off the dome. The "foam" was more like cardboard - very dense and thin. I pulled it off and made a similar ring out of neoprene, which was thicker. I glued it on with black silicone seal. Now, at night, it's a bit better, but still not good. One of the issues I may be having is the camera needs to be aimed so the lens is all the way towards the edge of the dome. Doing that, covers about 30% of the IR LEDs.

I'm thinking the best way for me to go is just replace the dome cam with a turret camera.
 
tangent

tangent

IPCT Contributor
Joined
May 12, 2016
Messages
4,421
Reaction score
3,654
bertsirkin said:
I got back up on the ladder and pulled off the dome. The "foam" was more like cardboard - very dense and thin. I pulled it off and made a similar ring out of neoprene, which was thicker. I glued it on with black silicone seal. Now, at night, it's a bit better, but still not good. One of the issues I may be having is the camera needs to be aimed so the lens is all the way towards the edge of the dome. Doing that, covers about 30% of the IR LEDs.

I'm thinking the best way for me to go is just replace the dome cam with a turret camera.
Click to expand...
out gassing from silicones can be trouble. a turret upgrade is a good option.
 
Mike A.

Mike A.

Known around here
Joined
May 6, 2017
Messages
3,828
Reaction score
6,385
That's kinda funny. I have that same cam and basically same experience. Just replaced the foam ring with my own thicker version made from craft foam this weekend. Though I don't know that mine ever really worked all that great to begin with. The multi-LED IR ring design isn't the best inside a dome and it's relatively weak. Same as you, I have it tilted up so some of that also is blocked and there's more glare off of the edge which doesn't help. Move it down and give it some light and it's a pretty decent little cam. Otherwise... meh. I got mine real cheap and it's just used as an added cam for over watch so no big deal here. I'd be disappointed if that weren't the case. If it were one that I relied on, then I'd replace it too.
 
You must log in or register to reply here.
Top