Are you sure for this url ? Cannot connect using http://
Dahua IP intercom: VTO3211D-P2 (new P & P4 ) door station - experience, review, firmware support?
riogrande75
Pulling my weight
You have PM!
Hi there, i'm a new owner of a VTO3211D-P2, version 2018-04-21 V3.200.9999000.0.R and i have some answers.
@JCFR i can reply to some questions :
I'll try the newer firmware this night, hope it's better. I want to use this VTO with Jeedom, i need a "ring" API call. It would be great if the device was capable of a webhook when someone press the "ring" button.
I think it's better to post here to help everyone, but if you want to speak French, just PM me !
@JCFR i can reply to some questions :
--> Same problem for me ! It is very annoing.
No problem for me with notifications, and i don't have a VTH. Did you check your network configuration ? Is your gateway OK ? Check the "P2P" settings too in "System config --> Network config --> P2P tab". Status must be "online".
Same problem with FTP on my Qnap NAS. It worked ONE time, but the jpg file is unreadable...
The SSH password is "7ujMko0 + your password". If you use "password" as a pass, then ssh password is "7ujMko0password". But don't expect much from this little dsh shell...
I'll try the newer firmware this night, hope it's better. I want to use this VTO with Jeedom, i need a "ring" API call. It would be great if the device was capable of a webhook when someone press the "ring" button.
I think it's better to post here to help everyone, but if you want to speak French, just PM me !
johz
n3wb
I do not think that that firmware is newer. Although it has a newer date stamp it is V1.000 and yours is V3.200 (and probably multi language)
John
You are right John, after searching, i can't find a newer firmware than V3.200... but, i found this file :
General_VTO3221D_Eng_P_32M_SIP_V3.200.0012001.0.R.20180330.bin
I tried unsuccessfully, still in V3.200.9999000 and no SIP Tab.
General_VTO3221D_Eng_P_32M_SIP_V3.200.0012001.0.R.20180330.bin
I tried unsuccessfully, still in V3.200.9999000 and no SIP Tab.
riogrande75
Pulling my weight
As far as I understand, VTO3221D ist a complete different device. So the firmware will not fit the VTO3211D.
Ho !! I was realy tired !!! I read 3211 instead of 3221 !!!! I agree, it won't work ! So my last chance is to export an image on FTP when someone ring, and watch this FTP with a script. I'll try something like that.
Last edited:
Still no luck with my VTO3211 and FTP server. I have tried on my Qnap NAS, on my computer with "samllftpd server"... nothing.
So i decided to try the SD card method. Th port isn't accessible from outside, you have to open the VTO by removing the 6 screws at the back. Then you'll see a SD card slot. There is also 4 pins that probably are UART... humm maybe i'll give it a try.
So i decided to try the SD card method. Th port isn't accessible from outside, you have to open the VTO by removing the 6 screws at the back. Then you'll see a SD card slot. There is also 4 pins that probably are UART... humm maybe i'll give it a try.
I take some photos of the inside, for curious people !
The main chip is a "HI3516 drbcv100": http://support.hkvstar.com/file/Hi3516E V100 Professional HD IP Camera SoC Brief Data Sheet.pdf
The memory chip is a Toshiba "TC58BVG0S3HTA00" 1Gb : TC58BVG0S3HTA00 | Mémoire | TOSHIBA MEMORY | Europe(EMEA)
Some images of the boards.
The main chip is a "HI3516 drbcv100": http://support.hkvstar.com/file/Hi3516E V100 Professional HD IP Camera SoC Brief Data Sheet.pdf
The memory chip is a Toshiba "TC58BVG0S3HTA00" 1Gb : TC58BVG0S3HTA00 | Mémoire | TOSHIBA MEMORY | Europe(EMEA)
Some images of the boards.
Last edited:
Knucklejoint
n3wb
I am using a VTO3211 with 2x VTH1550CH. Basic funtions works but P2P is not working at all. Is there anybody who managed to make it work? I will attached snap shoot from my setup screen. On the picture, I set the "Enable" check box, but below it says "Status : Offline". I refrehed and booted many times, no satisfaction. Am I doing something wrong?
Attachments
@Knucklejoint, it's working for me but i don' have a VTH.
Some news of the UART. The pins are NOT those located under the Ethernet and "control" connectors. The UART connector is on at the left of the main chip. I decided to solder on the other side, it's easier.
The PIN order is from up to bottom : RX, TX, GND, VCC
Then you'll be able to see the boot, and interrupt it by pressing a key ( * is often used). Remember to keep it pressed BEFORE and WHILE connecting power.
Now that i'm in, i need to find something to do with it
Ha ha ! Funny thing ! It's a VTO3211D-P2
Some news of the UART. The pins are NOT those located under the Ethernet and "control" connectors. The UART connector is on at the left of the main chip. I decided to solder on the other side, it's easier.
The PIN order is from up to bottom : RX, TX, GND, VCC
Then you'll be able to see the boot, and interrupt it by pressing a key ( * is often used). Remember to keep it pressed BEFORE and WHILE connecting power.
Now that i'm in, i need to find something to do with it
Ha ha ! Funny thing ! It's a VTO3211D-P2
Code:
> printenv
...
HWID=VTO3221D
...
Last edited:
Knucklejoint
n3wb
Thank you Kemar,
I have not tried yet. I will do it on weekend.
I have seen a button near SD-card. What is it for?
Is SD-card works?
I have not tried yet. I will do it on weekend.
I have seen a button near SD-card. What is it for?
Is SD-card works?
Knucklejoint
n3wb
How did you configure serial port (baud rate, data bits, stop bits, etc)? Is there any other things to set on Putty?
Knucklejoint
n3wb
I figure out serial port configuration
Knucklejoint
n3wb
I can see boot but what should I do for next step. There are "fail to load bootargsParameters.txt" errors. I attached snap shot of my boot.
Attachments
If you can see "booting the kernel", it's that your camera has boot, and you can access the web interface. If you want to use the bootloader commands, you have to interrupt the boot by pressing "*" key before turning power on and stay pressing it until you see the same thing than my last sreenshot.
I don't know what that "fail to load" errors are, i'm just trying to understand how it works, sorry.
I don't know what that "fail to load" errors are, i'm just trying to understand how it works, sorry.
Knucklejoint
n3wb
Thank you Kemar. I have contacted Aliexpress' seller, they said they will help. I will let you know the result
Crazykiller
Getting comfortable
It‘s the reset button. Holding for about 10-15 seconds will reboot your VTO and reset it to defaults.
Knucklejoint
n3wb
Thank you Crazykiller