Search results

On the RCA the restet button was a bit awkward to keep down under the rubber, had to use a fingernail to make sure it was down the whole time. My guess is the LED flash is the boot loader completing and the beginning of the firmware flash so if you are not getting the flash something more may be...

As soon as it powers up it will be red , you need to keep holding the reset button. LEDs will flash once, and still be red when they come back on, do not release reset button continue to hold the reset button until LEDs turn blue and doorbell announces reset successful, took about a minute or...

Thank you David, but also thanks to all the other contributors here too, since I was just trying every suggestion I read.

That’s strange, I have no problem using hik connect app on one device and rca App on another. Perhaps delete the camera from both apps and try adding it to the rca app first, I’m sure someone else will chime in (pun intended) with a fix shortly.

My pleasure, good to give back.

You can reinstall the rca app now you have it set up and set the chime from there. I prefer the rca app on my phone and the hik app on the iPad.

Or you could probably just change the wifi using batch tool or ivms back to your network and it will just work with your existing app you will need to initialise the SD card after you have it configured

I deleted doorbell from rca app and uninstalled, then installed hik connect app and set up as normal

Good luck this is another variation that did not work for me post 4519 by Skinah page 226 https://ipcamtalk.com/threads/new-rca-hsdb2a-3mp-doorbell-ip-camera.31601/post-464775

Had the same thing happen to me. After reading through the 101 and various posts I did the following and it recovered. Turn off power and wait for the red LEDs to go out disconnect power kit box and chime if connected remove sd card and format to FAT32 copy the HIK firmware to the card as...

I went back because of the device registration requirement, I couldn't have LaView on the phone and HIK Connect on the Ipad.

Yes RCA, EZVIZ and HIK Connect apps all working with the La View firmware. To use the LaView app I had to delete the camera from the other apps and register it with LaView but decided to go back to RCA on the phone and HIK Connect on the IPad because I have a HIK NVR

One more vote of thanks to Chadsturgill for testing all the firmware options, another happy camper here with no logo and onvif enabled on my RCA branded doorbell (with oval shaped rather than round camera surround)

In need to forward port 443 for remote access to home assistant but when I do the RCA and HIK apps both report the the doorbell as offline. Is there anything I can do to get them to both work together?

That’s a shame, I’d hoped an ONVIF update may have been on the way for RCA owners too. If anyone US based happens to be talking with Voxx support I’m sure many RCA owners would be interested to know especially since it is available on the Laview version now.

In the RCA App go to settings and it's 4th from the bottom "Device Version"

Sorry, meant RCA doorbell firmware version number that has onvif? I’ve not had an update available since v5.2.4 build 190124

What is your software version numner please?

I am certainly leaning towards there being different hardware versions. I have an early RCA version as per the screenshot from the video posted above and the area behind the camera runs very hot. I've tried all combinations of 12, 16 and 24VAC, with and without chime, resistor and power kit in...

Thank you, I did not know the hardware was different, that would explain why the firmware update is not being offered (and probably saved me from bricking the thing). I think I’ll go back to the RCA or Hik App they were much more responsive in terms of delay between doorbell press and phone...

I have the RCA branded version but have installed and registered the device on the LaView One iOS app but am not being offered the ONVIF update, it just says “no new version available”, what am I doing wrong, I have v5.2.4 bld 190124? Maybe I need to borrow an android device to update?

If you are speaking to them again I'd be interested to know what they consider normal. Stumbled across this the other day but have not had a chance to look at it in detail, not sure if already posted on here. FCC ID VIXHSDB2 Video Doorbell by Voxx Accessories Corp. Edit: Looking at the...

Thanks for the model info. Seems like strange advice. I assumed that the reserve power is there to allow any recording that is in progress to have the file closed properly and avoid corrupted files on the SD card. I have a dash cam that has no battery but uses a capacitor for the same reason...

My unit runs very hot regardless if I install the supplied resistor with no chime or supplied power pack with a mechanical chime and the app set accordingly of course. The unit works fine in both modes and does not have any rebooting or wifi connection issues. I can’t work out what I am doing...

HIKVision has released new firmware v4.1.65 for 76, 77, 96, NI-I Firmware - Hikvision UK & Ireland Auxiliary Menu Reset password via email RAID Related Unbinding Hik-Connect in local GUI eSATA Automatic Backup Download Major firmware from Hik-Connect to hard disk and upgrade Except 7732NI-I4_24P

I have just received my HSDB2A and have it running with my existing door bell 20VAC supply, I have it running on the bench upstairs with resistor (no chime), the wireless router downstairs and had no connection issue and setup was reasonably painless. The one concern I have is the unit runs very...

Hello, I'm quite new to nvr's so have begun my learning curve by reading here. I'm currently looking at the Hikvision NVR DS-7108N-SN/P units on eBay with the warnings not to upgrade firmware and judging by the photos these come with the 3.0.7 firmware 140805 build. So I can get one on the way...