DS-2CD4A26FWD-IZHS/P firmware

[Jeremeyh]

After much searching I have found the correct firmware for DS-2CD4A26FWD-IZHS/P ANPR. I accidentally upgraded the firmware with the non P version and could only get a maximum of 25 fps. I installed the correct firmware and now I've got 60 fps again.

 

[Mauricio Gonzalez]

Wow! Thank you very much! but, i have a 2 questions for you

1.- At the time that you installed the firmware that does not have the P, the camera besides that it did not work at 60fps, it also lost the LPR functions ?, I mean, the intelligent events of intrusion detection and line crossing appeared? I just need to achieve that; By mistake I bought the camera that has the P and I intend to install the firmware of the model ds-2cd4a26fwd-iz (h) (s) that was the camera that I really wanted.

2.- Where did you get the firmware for the camera ds-2cd4a26fwd-izs / p?

 

[Jeremeyh]

Still operated as an lpr camera, but lost the 50 fps.
For the firmware I got it from hikvision site in Australia. Be careful to get the correct region as different countries have different plates. Eg the Australian on didn't detect new Zealand plates correctly, so I contacted hikvision support and they sent me a link for the new Zealand version.

 

[dennis_ca]

I have DS-2CD4A26FWD-IZHS8/P and FW is V5.4.7 build 180611. I believe the FW is compatible, so I can share it if you want.

It fixed some issues I had with detecting the reverse traffic, but I still have over-exposure issue: when a car passing the camera, it recognizes the plate, then screen flicks. So, if you have two cars driving fast after each other, the second one passes by without plate detection.

 

[medtech1]

Hey Dennis, can you please provide hikvision's url for the V5.4.7 build 180611 firmware version?

I just picked up a DS-2CD4A26FWD-IZHS/P from a local dealer in Vancouver, BC and would like to update it (currently it has v5.4.5 build 170914).

Also, I find the Hikvision site confusing... as it shows the "DS-2CD4A26FWD-(IZHS)(LZS)/P" line of cameras "NEW", yet the "DS-2CD4A26FWD-IZH" is shown as discontinued on the US site.

I assume the new versions are specific to the IZHS/P model?

DS-2CD4A26FWD-(IZHS)(LZS)/P - Hangzhou Hikvision Digital Technology Co. Ltd.

US Site:
2MP WDR Smart IP Bullet Camera

I'm not sure what the P is, unless it describes the lens? 2.8-12mm or 8-32mm

 

[Jeremeyh]

Izs is the zoom lens. P is number plate camera

 

[DazNick]

Hello,

I have been to many hik sites but I can not find the specific firmware for the LPR,
I am told if I updated to a non LPR then It can never be used as an LPR type again and only the dealer I brought
It from has to activate the LPR mode or something like that. I have contacted the dealer they say they can not help me
and to look on the internet!
I do not want to brick or loose my LPRR function.
Can someone please point me into the right direction.
This is my current version:

Model DS-2CD4A26FWD-IZS
Serial No. DS-2CD4A26FWD-IZS20170627CCWR78*******6
Firmware Version V5.4.3 build 161027
Encoding Version V7.0 build 160822

Thank you
Darren

 

[medtech1]

Hello,
This is my current version:

Model DS-2CD4A26FWD-IZS
Serial No. DS-2CD4A26FWD-IZS20170627CCWR786550936
Firmware Version V5.4.3 build 161027
Encoding Version V7.0 build 160822

Thank you
Darren

I have two of these... DS-2CD4A26FWD-IZHS/P and DS-2CD4A26FWD-IZHS8/P. I've upgraded them to v5.4.5 build170914. (firmware is identical).

You can get it here: Firmware and search for "DS-2CD4A26FWD".

The firmware should be the same for yours, as the only option missing is "H" which is heater.

There is a EU Portal as well, but the firmware is not the same:

DOWNLOAD EU PORTAL

If you review the PDF (R0'R2'R6'R3ANPR V5.4.5 _170519Release Note--External.pdf ) for the EU firmware, and go to the very bottom, it shows that all these models take the same firmware.

Good Luck!
Michelle

 

[DazNick]

I have two of these... DS-2CD4A26FWD-IZHS/P and DS-2CD4A26FWD-IZHS8/P. I've upgraded them to v5.4.5 build170914. (firmware is identical).

You can get it here: Firmware and search for "DS-2CD4A26FWD".

The firmware should be the same for yours, as the only option missing is "H" which is heater.

There is a EU Portal as well, but the firmware is not the same:

DOWNLOAD EU PORTAL

If you review the PDF (R0'R2'R6'R3ANPR V5.4.5 _170519Release Note--External.pdf ) for the EU firmware, and go to the very bottom, it shows that all these models take the same firmware.

Good Luck!
Michelle

Thank you Michelle,

I tried both of those firmware versions from US and EU
US: dz20170817_074_r3_en_std_5.4.5_170914_car.zip
EU: FF_R3_EN_STD_V5.4.5_Build170519_CAR.zip
Did not work, Status: The version of upgrade file mismatches.

I found another version on the US Hikvision site for specifically 'DS-2CD4A26FWD-IZS' <-- No other abbreviations
apparently listed as 'last version for discontinued product' for just the 'IZS'
ds-4x24fwd4x26fwd6026fhwd_ip_camera_firmware_v5.4.41_170310.zip
I did install it BUT I lost the LPR function on it, however It gave me
these two modes SMART Event + Face Detection, SMART Event + Heat Map

Hmm, Heat map, never heard of that function before

So, I went looking for my ORIGINAL version V5.4.3 build 161027
found it on the EU site and now I am back where I started and I have my LPR function back

Maybe there is no later version then V5.4.3 build 161027 for just the -IZS LPR function.
your camera is a newer type with the extra H, S8/P etc

Regard's

Darren

 

[medtech1]

Thank you Michelle,


So, I went looking for my ORIGINAL version V5.4.3 build 161027
found it on the EU site and now I am back where I started and I have my LPR function back

Maybe there is no later version then V5.4.3 build 161027 for just the -IZS LPR function.
your camera is a newer type with the extra H, S8/P etc

Regard's

Darren

Hey Darren, I'm surprised. The PDF link I added to my previous post came from the EU site and is documentation specifically for V5.4.5 170519 (DOWNLOAD EU PORTAL) . Within that PDF it indicates this is firmware for ANPR cameras and the 5.4.5 170519 is compatible with DS-2CD4A26FWD-IZS/P. Is yours a DS-2CD4A26FWD-IZS or DS-2CD4A26FWD-IZS/P? The /P is for ANPR plate reading camera.. so I would assume that is your model?

 

[DazNick]

Hey Darren, I'm surprised. The PDF link I added to my previous post came from the EU site and is documentation specifically for V5.4.5 170519 (DOWNLOAD EU PORTAL) . Within that PDF it indicates this is firmware for ANPR cameras and the 5.4.5 170519 is compatible with DS-2CD4A26FWD-IZS. Is yours a DS-2CD4A26FWD-IZS or DS-2CD4A26FWD-IZS/P? The /P is for ANPR plate reading camera.. so I would assume that is your model?

Hi Michelle,

My model does not have the P in it, my complete model number says: DS-2CD4A26FWD-IZS20170627CCWR78*******6

The /P is for the Iris, all cameras that have model DS-2CD4A26FWD are going to be ANPR or LPR mode but only if enabled.

Here is a great reference link that details the Hikvision model numbering system.

Regard's

Darren

 

[medtech1]

Hi Michelle,
d.

Here is a great reference link that details the Hikvision model numbering system.

Regard's

Darren

Thanks for that info. Hopefully someone else chimes in if the know then where you can get newer firmware for your specific model.