looney2ns
IPCT Contributor
Yeah, I'd try that.yes I updated PTZ as well...the 2.623 180913 .bin along with the 3.02.93 ptz
...I think I did re-import my settings...could that be the issue? should i clean out the settings with a reset?
Yeah, I'd try that.yes I updated PTZ as well...the 2.623 180913 .bin along with the 3.02.93 ptz
...I think I did re-import my settings...could that be the issue? should i clean out the settings with a reset?
no luck resetting config...gonna have to roll back to April firmware....not finding it on the dahuawiki site...anyone have it?Yeah, I'd try that.
Hi ! experienced same thing as you with the 180913 firmware...any chance you have the April 2018 version you could upload or send? Thanks!Anybody else upgrade to the 180913 firmware and have problems with the web interface becoming unresponsive after about 6-8 hours? I started noticing the problem on the previous version from August, but not as extensive, so I updated when I saw the 180913 available and it got way worse. I finally reverted back to the April 2018 version and it's been solid since then. I did do a full factory reset after installing 180913 including wiping the network settings, it made no difference. Not sure if it's something on my network that may be causing the problem or something built in to that firmware version. I don't have an NVR or anything else communicating with the camera, so that seems unlikely to me but you never know I guess. I don't have the camera on a separate VLAN yet.
Good find. I downloaded that and compared with the one I found and it is 100% identical, byte for byte. That does help confirm no funny business was performed on the firmware image by an unscrupulous third party.Download April firmware on Dahua Italy official site Firmwares
great! gonna give this a shotDownload April firmware on Dahua Italy official site Firmwares
If you have set the PTZ Profile in BI to the "Dahua New" profile, then this could be the problem.It's working great although BI seems to loose PTZ control of the cam once in a while. Then I have to log into the web interface to regain control.
View attachment 35613
Nice job, do you have a way to remove it for service?I finally finished the recessed install of my SD49225T PTZ. It was a lot of work but it's more discrete this way. I mounted it inside the 2nd story window frame above the garage door. The other cam is a Dahua 8MP to keep a wide angle eye on things. It's working great although BI seems to loose PTZ control of the cam once in a while. Then I have to log into the web interface to regain control.
View attachment 35613
If you have set the PTZ Profile in BI to the "Dahua New" profile, then this could be the problem.
Set it to ONVIF(OXML) and then it works fine. At least that did the trick for my 49225 in BI.
I've mailed with bi support, and he is looking to fix it
Thanks looney. I left the screw heads exposed so if needed I can still remove the wood panels underneath and remove the camera. But the spackling in the the joints will have to be reapplied and repainted afterwards. Probably an hour or two of work. Not ideal so hopefully it will give me many years of trouble free service!Nice job, do you have a way to remove it for service?
I tried the ONVIF setting a couple of times but I don't get any PTZ response at all. "Dahua New" is the only setting that works for me (not reliably). Maybe my firmware is different than yours.If you have set the PTZ Profile in BI to the "Dahua New" profile, then this could be the problem.
Set it to ONVIF(OXML) and then it works fine. At least that did the trick for my 49225 in BI.
I've mailed with bi support, and he is looking to fix it
I am using that version and Onvif works fine for me. Be sure you use the find/inspect button and it should set everything for you.I tried the ONVIF setting a couple of times but I don't get any PTZ response at all. "Dahua New" is the only setting that works for me (not reliably). Maybe my firmware is different than yours.
System Version 2.622.0000000.7.R.R4.2510.9A.NR, Build Date: 2018-04-04
WEB Version 3.2.1.563437
ONVIF Version 16.12(V2.4.1.513183)
PTZ Version 3.02.93.RHNZ_170518_22722
Thanks Tinman! I deleted the camera and added it from scratch using find/inspect (I thought I already did that originally) and now ONVIF is working!I am using that version and Onvif works fine for me. Be sure you use the find/inspect button and it should set everything for you.
View attachment 35673