Recent content by Bigg1es

Thanks Flintstone61, I only needed your reply, the suggestion in the Link that it was an audio setting was spot on. Both Logitechs now working. For anyone else arriving at this old thread through Google fix is - camera settings, audio then select Other Direct Show device and choose your webcam...

I have the same problem. I have several IP cameras and two Logitech C270 USB webcams. they have worked fine for years then a couple of months ago they decided to stop working. I have done all the usual things many times over 8 weeks. The only thing which worked was delete and add new camera...

I am trying to help a vulnerable relative who has been the repeated victim of criminal behaviour by a neighbour. At my suggestion he installed an 8 camera system. Unfortunately he went to a popular online vendor and bought the cheapest system and while it seemed to work, it has proved near...

I have an Nvidia , however it was not a hardware issue, it was a BI software issue and since the update I have not had a single recurrense of the no signal problem. Most of my cameras are hard wired with a couple on plug adapters. Non use wifi connection.

There is a new update today, 5.2.2.2 and after updating it I have all cameras running. I did have some issues with the update. I didn't mention earlier but sometimes my Blue Iris doesn't close properly. This update addresses that issue but I did have it not shutting down during the update which...

That's interesting, it seems to be a similar issue. I also have sound available through the no signal cameras. I hadn't looked ta Bitrate before. My Hikvision Dome says Frame Rate 1.40/0.00< fps, bit rate 30.05 kB/s. Right now the Hikvision Cube is working for the first time in a few days and 2...

Update - the problem temporarily fixed itself for several days and I had all cameras working. Then I made a small change to the "end trigger unless re-triggered with " and immediately lost both of my Hikvisions. Obviously tried immediately putting the setting back to what it was (30 sec) but it...

Update, while I have not been actively working on the issue for the last few days, the problem persists. After each new start, usually one camera is no signal. Its not always one of the Hikvisions but usually it is and typically its the one wired into the hub. Im starting to think its may be...

Thanks, I will try that tomorrow. Currently I am trying to update the Nvidia Graphics driver and its not going well. As soon as I get that working I will start work on Blue Iris again

Update on the update / having updated my nvidia drivers and restarted, mz Hikvision cube is now back to no signal. Which means my all cameras working status lasted less than 10 minutes. I will tinker with the port numbers as per zour post.

Thanks for advice. I don't have a good understanding of port numbers. With the cube I just tried every likely port number. I guess I will have to change them to the recommended ones. Just now the last camera just started working again, so right now, as of this minute I have all cameras working...

Update. I have just been tinkering. I noticed that some of my cameras had a high max frame rate. Normally I set the cameras at 15 frames pm, but sme where higher. I just reset several cameras down to 15 and suddenly my Hikvision dome started working again.... and at exactly the same time, one of...

I should point out the screenshots of my blue iris show a second camera with no signal, a foscam. this is not a problem, it is unplugged. Its just the Hikvision which is a real no signal.

1) chrome will not work to view older cameras videos. Chrome does not support plugins. You must use Internet explorer or Pale Moon 32. Using the Hikvision browser interface, the cube on the new firmware works in Chrome but the dome camera with older firmware does not, however, using seamonkey...

1) What web browser are you using ? I have a wide selection of Browsers but mainly using chrome. No difference observed in other browsers. 2) what Version of BI are you using ? As above, just updated it, therefore the very latest , 5.2.0.5 x64 3) make and model of the power line adapter. BT...