Recent content by CJ133

  1. C

    5442T-ZE backlight BLC question

    Well, For what it's worth even though I can't test the IPC-T5442T-ZE yet because I'm not home, I did test on the following cameras. IPC-T22IR-ZAS-S3 IPC-T58IR-ZE-S3 IPC-T2231T-ZS - four cameras IPC-T2431T-AS-3.6mm IPC-T2431T-AS-2.8mm All of them give me the box to move around when BLC is set...
  2. C

    5442T-ZE backlight BLC question

    You're right, I made a wrong assumption. I'll need to give that a shot and see what happens.
  3. C

    5442T-ZE backlight BLC question

    Just to be sure, I tried using Edge and it behaves identically. I've tried, absolutely nothing happens.
  4. C

    Exporting clips - best way?

    I've always exported clips using the UI3 interface but need to export a few that I want to be as good as they can be regarding quality. I'm assuming if I use Blue Iris I can get something that's not re-compressed etc like I do via UI3? My concern is I need the date / time that Blue Iris adds...
  5. C

    5442T-ZE backlight BLC question

    I can't remember if this changed with the more recent firmware, or if it's always been this way but under backlight, if I select BLC on my 2MP cameras I can select custom and move a box around to the area I want it to adjust to. With the 5442T-ZE there's the same options except no box shows up...
  6. C

    Blue Iris UI3

    So, I recently started having an issue where I cannot download clips via UI3 anymore. All I get is a download failed error. It worked up until about a week ago. I tried updating BI and restarting the computer, no change. Tried restarting the mobile devices trying to download the clips and no...
  7. C

    Blue Iris UI3

    I just updated to 5.9.9.27 because it was overdue anyway. Nothing useful under the log, though I noticed it detected Intel graphics. I don't know if it would help or not, but these are the settings I'm using under the cameras. They're all Dahua from Andy.
  8. C

    Blue Iris UI3

    I just had time to do some tests. Removing the substream does solve the issue and it looks pretty good, however the problem returns when I put the substream back. It appears to be doing this on all 8 cameras. I did find one with the smart codec enabled and I turned it off but it didn't effect...
  9. C

    Blue Iris UI3

    Here's 3 out of 8. I have a mixture of 2mp and 4mp cameras so I gave you my two important 4mp and one of the 2mp. The rest should match these.
  10. C

    Blue Iris UI3

    I think that's the problem because when I go full screen on any of the cameras the quality never goes over to main, it just stays looking bad. On the pc running the cameras you can see it switch over to main and it goes from the way my UI3 looks on my phone to fantastic.
  11. C

    Blue Iris UI3

    Switching between main and substreams might just be me remembering what BI does rather than what I see on my phone. Here's the Streaming 0 profile. I just tried it on my son's ipad and it seemed like it was the exact same as my phone. Low quality and motion makes it worse. I think I need...
  12. C

    Blue Iris UI3

    I was going to start a new thread because I don't know what I have going on is a bug, or my stupidity but I'm fairly sure it's UI3 related. For a long time I was running all of my cameras on H265 but I recently changed to 264 for both main and substreams. I feel like ever since I did that...
  13. C

    IPC-HDW5442T-ZE New cam from Dahua :)

    I'm going to ask a really dumb question but, do typical switches and nics even have the grounding needed for shielded cat5 or 6 to work? It looks like the RJ45's are shielded as well. I don't recall seeing that on the jacks of my switches, but I also never really looked.
  14. C

    IPC-HDW5442T-ZE New cam from Dahua :)

    @David L My main complaint with cat 6 is terminating it. I mean, I can and do, but cat5 is so much easier.
  15. C

    IPC-HDW5442T-ZE New cam from Dahua :)

    Interesting. I don't think I've ever used shielded ethernet wire before for anything. Never had a need that I was aware of at least. All of mine is cat5e unshielded. When did shielded cat6 become recommended?