LaGraBow's latest activity

  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    Still going great. FW - V4.000.00AC000.0
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @Revo2Maxx Yes I will report back. This is the longest the cams have ever stayed on the monitor.
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    OK. NVR reset done. It has been two hours and cameras are ALL still showing - no red locks. I did not get the cams back in the original...
  • L
    LaGraBow reacted to Revo2Maxx's post in the thread Amcrest NVR 4108-HS with Like Like.
    So I am sure there is. and there is a lot of Videos out there but I made a fast 10min video showing what I do to reset the NVR.. Now...
  • L
    LaGraBow reacted to Revo2Maxx's post in the thread Amcrest NVR 4108-HS with Like Like.
    41xx HS or A2 are still only 80Mbps so you will want to step up to the 42xx or 52xx ultra line of NVRs for more bandwidth.. Just...
  • L
    LaGraBow reacted to Flintstone61's post in the thread Amcrest NVR 4108-HS with Like Like.
    Amcrest makes a 16 channel version of that,(4116) which I bought used on the forum for 99bux. it does a better job running 8 cams. and...
  • L
    LaGraBow reacted to Revo2Maxx's post in the thread Amcrest NVR 4108-HS with Like Like.
    Doing a Factory reset with 8 cameras if you don't remember where the cameras are on grid and want them to stay at that location then...
  • L
    LaGraBow reacted to bigredfish's post in the thread Amcrest NVR 4108-HS with Like Like.
    No benefit to buying an 8 when you can have a 16 for $30 more...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    yes and very delicious too I am now installing Palemoon to try again.
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @wittaj Sorry forgot an important piece of info. Currently using Linux distro openSuse Tumbleweed. Tried Palemoon. Didn't work.
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    When I originally did my cameras I just set them static through the web GUI. Some show as static, some show as manual on my router page...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    If I am not doing the cams, should I unplug them? Will my camera IP's stay the same if I don't reset them?
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    OK So, to factory reset. I have gone through your video, thank you for making it @Revo2Maxx 1] Do I have to unplug the cams before I do...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    OK TY done
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    where is that being shown?
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @wittaj Is this what you mean?
    • OperationInformation.png
    • OperationInformation.png
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @Revo2Maxx connected router into NVR and cam system through 8 port switch Error: I could not see your service on nnn.nnn.nnn.nnn on...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @bigredfish My NVR and cams are separate from my router [no cable] I cannot get to the NVR Web GUI because my NVR is not connected to...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @wittaj I am guessing you mean accessing the router? When I took the NVR off the router I rebooted the router and after the reboot none...
  • L
    LaGraBow replied to the thread Amcrest NVR 4108-HS.
    @bigredfish No, NVR not port forwarded. Cams and NVR separated from router rebooted router rebooted NVR Setup: NVR to 8 port switch 6...
Show older items
Top Bottom