Recent content by marinenickel

  1. M

    Not all cameras listed under Alerts

    I synced the profiles in the Recording tab to profile 1 and deleted the two folders yesterday. Checked back this morning and the folders are now gone from the Alerts drop down as well as in explorer.
  2. M

    Not all cameras listed under Alerts

    As am I, and why there are files for these 2 specific cameras. I've gone through the settings of each of the cameras multiple times and cannot find any difference.
  3. M

    Not all cameras listed under Alerts

    I see all the cameras when I go to all clips. Of course that doesn't show just alerts, but the whole recording. At this point I imagine it has something to do with the age of the cameras and tweaking the sensitivity settings.
  4. M

    Not all cameras listed under Alerts

    The 2 SWAN bullet cameras in my Garage are the only ones I can't reliably get to show an Alert in the Alerts view. They are fairly old from 2016 so I might just look into replacing them with something nicer/newer. Still baffled why the reolink/Garage cameras have folders in the Alerts folder...
  5. M

    Not all cameras listed under Alerts

    Nope, I double/triple checked and all Cameras are set to the "New" folder. Yes, I verified everything this morning. So Driveway is showing alert clips, it just doesn't have a folder under "Alerts". However I have 2 other cameras in the garage and neither is showing in the clips section when...
  6. M

    Not all cameras listed under Alerts

    You bet, here is some more info. BI Version = 5.8.1.3 Using CPAI only on my older cameras. It is not being used on the reolink, garage or Driveway (screenshots of below). Let me know if I need to drill down deeper in any of these.
  7. M

    Not all cameras listed under Alerts

    I have 7 cameras currently setup, but not all of them have a folder under alerts. Looking at the Alerts folder (as set in Storage) I only see Garage & reolink. The reolink has nothing but *.dat files and Garage has a couple of *.dat files and a whole lot of JPEG's. Haven't been able to find...
  8. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    Good to know. I only run 1 SSD and 1 Purple drive, but nice to have an option to add a second one if ever needed.
  9. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    Yes, thank you! Will check if there are any updated GPU drivers. Also will look into i5-8500 Ho Elitedesk G4 800 SFF. Appears they are really cheap PC's. I know my Optiplex is getting quite old.
  10. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    CAM8 is the new one and I haven't adjusted the FPS/Key yet.
  11. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    So I set hardware accelerated decode to No, re-enabled the camera and now it's showing. Is there any reason to re-enable this setting?
  12. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    I can't imagine adding 1 camera would cause the system to become unstable. Especially since I disabled one the new one is currently replacing. But here we go: Dell Optiplex 9010 i7-3770 16GB RAM C Drive = 840 EVO (250GB) Cameras are all at 15 FPS Hardware Decode is set to Default for all...
  13. M

    Adding new camera (IPC-T54IR-ZE-S3) causes BI to flicker/unstable

    I purchased a couple of IPC-T54IR-ZE-S3 to add/upgrade my current list of cameras. The camera is initialized/configured and working. Going into BI I put in the IP and click on Find/Inspect which comes back with Once I enable the camera BI starts becoming almost unusable. The clips on the side...
  14. M

    Looking for camera upgrade suggestions

    Looks like IPC-T54IR-ZE S3 is a good one to go with.