Recent content by tazman
-
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
You're right. I never noticed that point before, but with the new firmware if you do not use IE, it tries to tell the web browser is not suppoted. Of course I'm using linux :) but never mind I have a wmware with window and IE ;) So now, the CN firmware for the G0 (version 5.89) is in the box... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
well done, That's new, now with new firmware you have the "not supported page"... I did not have it before and always use chrome :) well now I have: Which sounds good ;) Do you know the default password... and how to change language ? -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
using IE, I have a 404 and the cam try to publish the notSupported.asp page (which should tell me this device is not supported, i guess) Nothing on SADP -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
same result, it goes into the cam, the update has been done, uncompressing kernel is ok but during the boot you have a lot of errors It's like hardware is compliant with firmware ? -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
For serial that's DS2CD3145F-IWS 832701229 and the previous firmware (because there's no more fimware in it) was 5.5.0_170728 -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
HKVS # upf Erasing [env] . Erasing at 0x160000 -- 100% complete. done Erasing [sys0] . Erasing at 0xb60000 -- 100% complete. done Erasing [sys1] . rasing at 0x1360000 -- 100% complete. done Erasing [app0] . Erasing at 0x3960000 -- 100% complete. done Erasing [app1] . Erasing at 0x5f60000 --... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
Hi, thank you. This firmware is uploaded and accepted by the cam but... The linux kernel does not work fine, ioctl et db are not working and you have a lot of error Using a browser and trying to access to the webserver into the cam I have : http://192.168.1.64/notSupported.asp ==> Access Error... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
About features supported by the booloader, here are the commands: ? - alias for 'help'␍␊ base - print or set address offset␍␊ bootss - boot from snapshot image␍␊ cmp - memory compare␍␊ cp - memory copy␍␊ crc32 - checksum calculation␍␊ ddr - ddr training function␍␊ format... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
When I power on the ip cam I have the following: U-Boot 2010.06-209953 (Jul 29 2016 - 10:09:34)␍␊ ␍␊ NAND: 128 MB␍␊ *** Warning - bad CRC or NAND, using default environment␍␊ ␍␊ Hit Ctrl+u to stop autoboot: 3 <0x08><0x08><0x08> 2 <0x08><0x08><0x08> 1 <0x08><0x08><0x08> 0 ␍␊ ETH0... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
To be honest I don't know. I tried to check on the xls sheets coming from hikvision but this model is not present. May be on the PCB ? Do you know where ? I tried to upload several G0, G1 and so on firmwares as well, without success. Sometime i've go a missmatch message and sometime a message... -
T
Hikivision - IP Cam - How to Force a firmware into an IP CAM
Hello, I have Hikvision cameras bought from Aliexpress: DS-2CD3145F One of them is no more working since I decided to try to flash the firmware with a new. Actually, using the RS232 and U-Boot I used a command which clear all the partitions (what I saw) and try to download a new firmware. The...