Recent content by UmDaMan

  1. U

    A tip on how to repair your ethernet cable on your Dahua Camera when animals attack! :)

    Yea. I have never used the connector on my cameras. just guessed it was some sort of power input for if you did not have a POE network switch.
  2. U

    A tip on how to repair your ethernet cable on your Dahua Camera when animals attack! :)

    A few weeks ago, while I was on vacation, I noticed that one of my cameras had stopped working. After some investigation, I discovered that a squirrel had mistaken the cable for a snack! After searching for a replacement, I found the perfect solution on Aliexpress.com...
  3. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    Yea the other issue from my July 2019 build which is what I had before updating, all the other FW's that I tried to go that were newer than July 2019 something happened with the HDMI output. I no longer get a video on my monitor that uses an HDMI to DVI adapter. But works on monitors that...
  4. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    OMG! It's 100% NVR firmware related! FW: DH_NVR5XXX-4KS2_MultiLang_V4.001.0000006.0.R.210208.bin No good. I even updated the problem camera to General_IPC-HX5XXX-Volt_MultiLang_NP_Stream3_V2.800.15OG004.0.R.201203.bin, and that did not fix the disconnecting every 3-5min. I decided to go back to...
  5. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    Ok, I'm going to let it sit for an hour. On the NVR itself I do not see a refresh, only on the web interface. So maybe I will get lucky and they will get moved to the bottom. If not something for sure is wrong with this current FW release.
  6. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    I have deleted them all from the bottom list. Now they all just show up on the top section. They do not automatically move below. Also the one that I did the factory reset isn't even showing up anymore. I'm almost thinking it might be time to go back to an older firmware, to see if the...
  7. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    After I upgraded my NVR firmware and finding the disconnecting issue with Cam1, I did a factory reset on the NVR to see if that issue with CAMERA 1 would go away. When I did that my only option was to add all the cameras manually as they were not adding automatically. So that is why I figured...
  8. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    On my first attached image you will see 3 & 5 RED, as I swapped the ports. I waited and nothing changes. Its like each port is looking for the camera with the IP that you see listed on each port. Port 1 original was 10.1.1.65. I did finally get it to find the camera, I forgot my IP on my NVR...
  9. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    Right for some reason it's not doing this. After factory reset of the camera I plugged into Port 1, left it there for 5-10 min. Nothing happens. Never discovers any new devices. I've refreshed many times, and it never shows that it found the camera.
  10. U

    IPC-HFW5442E-ZE Factory Reset now NVR will not find the camera.

    My NVR Model: NVR5208-8P-4KS2E FW: DH_NVR5XXX-4KS2_MultiLang_V4.001.0000003.1.R.200813 IPC-HFW5442E-ZE FW: V2.800.0000000.17.R Build Date: 2020-06-20 IPC-HFW5442E-ZE FW: V2.800.0000000.0.R Build Date: 2019-05-21 So I wanted to do a factory rest on my camera with the build 2020-06-20...
  11. U

    Dahua NVR virtual host not working to access attached POE cameras

    I have the following cameras: (2) IPC-HFW5442E-ZE IPC-HDW2431TM-AS-S2 IPC-T2431TM-AS-S2 IPC-HFW2231T-ZS Yes I have hit the refresh many times. I waited for an hour. When at the top section before adding, they are also at the port 37777. I think when you first get the cameras they are I...
  12. U

    Dahua NVR virtual host not working to access attached POE cameras

    I'm having the same issue. I did a factory reset seeing if it was resolve a couple bugs I have been having since FW build July 2019, on my NVR I re-configured everything, but the cameras do not move to the bottom by their selves. When I move them down manually they are all at port 37777 vs...
  13. U

    NVR5208-8P-4KS2E , No HDMI output after Upgraded to V4.001.0000006.0, Build Date: 02-08-2021

    NVR5208-8P-4KS2E I upgraded the firmware on my NVR, previous was a 2019 build. I should have wrote down the exact date! I upgraded to the following: v4-001-0000006-0-r-210208.55064 (V4.001.0000006.0, Build Date: 02-08-2021) After the upgrade, I lost my HDMI output. Now only VGA output works...
  14. U

    NVR5208-8P-4KS2E Can you configure a BEEP sound on IVS detections?

    Yes works perfect!
  15. U

    NVR5208-8P-4KS2E Can you configure a BEEP sound on IVS detections?

    I was looking all over. I just didn't dig deep enough into the configs. Thanks for your help! Thanks!
See more
Top Bottom