Search results

A comparison (mounting templates overlayed on each other) and side by side photos would go a LONG way towards selling the new S3 product on Amazon. (While you are at it, put the horizontal field of view in degrees in the Amazon page for the 2.8/3.6/6.0, not everyone wants to calculate the FoV.)...

Please read your own post... You are clearly not replying to the OP about 'what does it gain me' in anything you write. You are stating you don't know where the firmware is. This is the very first request of all three posts. You state that I should not upgrade until I read it. I cannot read it...

We have 3 people looking for firmware. Your time would be better spent writing an article for the Wiki here on the general subject of firmware since there are none. OK? Before you jump to yet another conclusion about overheating, please note it it takes a week (or more) to heat up but then...

The 'mansplaining' is unneeded and not appreciated. Your reply is way off-topic. If you want to start a new thread titled 'updates are personal', please feel free...

ditto - I looked in 'downloads' here... but do not see anything that looks correct. I have one camera that pixelates the bottom 10% of the camera after runnign for a week and needs to be power cycled to get steady video again... Device Type IPC-T2431T-AS-3.6mm System Version...

BINGO.... initially during the PoE problem I was local, but to continue troubleshooting from home, I used RDP... and this feature added to the problem... I have changed to unrestricted. Thank you so much!!!

Interestingly, the delay is down to 7-8 seconds.... but that still seems like a lot... AND the clock on the camera in BI only updates every 5 seconds... That does nto seem to be normal.. I did a factory reset less than 2 weeks ago, and have only changed network settings, toggled the PTZ...

Yours is the closest answer... I originally assumed power issue since it was an action that drew power that caused the reset, and turning illuminators off saves power. The Cisco switch has automatic PoE negotiation, and can recognize a class 4(30W) device, however it defaults to 802.3af and the...

restarting, rebooting... Yes, that is on my list for the day, but a port cannot cause an 18-20 second delay in video, that is a LOT of data in a buffer, and a switch just doesn't have the ability.

I never said the camera settings were resetting, I said the whole camera was resetting... and that does not explain the long delay in the video feed!

maybe the log should show something more informative than 'abort'???? 85 2023-04-08 16:04:32 System Application started up 86 2023-04-08 16:04:32 System Abort 87 2023-04-08 15:53:26 admin Login 88 2023-04-08 15:52:54 System Certificate Management...

FYI - I have been a Cisco CCIE for over 20 years... I know a bit about networking....

attempting to move it in either Chrome or BlueIris cause the problem....

23AWG, 30 ft long, checked with fluke nettool... Like I said, it worked fine for a week... edit - you see where my Cisco switch can supply 30watts per port, but is only beign asked to supply 15.4Watts, correct?

I have issues with the camera resetting if I change position from the web interface or from BlueIris. The web ui kicks me out and I see 'No Signal' Error80000274d (Failed to connect) in BlueIris Camera purchased about a week ago, I set it up by reading this thread and worked fine until...

Yes, bluetooth would provide more granularity, and I can use it also, and I am sure if someone implemented an interface to BI, it would be as easy to do one as the other... The issue is sensors... WiFi AP's are ubiquitous.. I am a Cisco CCIE and have worked with Wireless location for many...

Anyone hear of such a thing? What a great plugin/program to have. Yes, there might be hundreds of addresses at any given moment in time, but with a little work, you could narrow it down to a dozen and alert if they came back in the future for a positive visual ID...

Sorry, I meant to include 'at a lower cost' because it does need all the fancy stuff that required the cpu and software. I want the big sensor, but 12 $250 cameras is a big hunk of change.

Do you think they will make a camera with the big sensor, but not all the features for the people that use their NVR for those features?

I have a Frontier supplied Arris NVG468MQ router (it is my only router) and a new Dahua NVR, and have the same question. I can use either device I suppose for the DDNS, but neither seems to be a perfect fit... any hints on configuring for ipctddns? Here is the dahua(I don't think it will...

I figured it out... instead of double-clicking to add to the view, right click and select 'Main Stream'. (you cannot change existing view from sub-stream to main stream, and if you change from main to sub, it locks up that view window)

yeah, I am a long time BI user, but thought I would try a 8-channel AI NVR for a new system... might have bitten off more than I wanted to chew.... wish they could port BI to run on the NVR!

I have read that 300 page thread it a few times, do you have a more particular pointer? edit - that thread was extremely helpful in getting the DB2 working in the Dahua NVR to begin with, along with teaching me direct links to snapshots and how to access with VLC player. I just don't see...

I can see my Nelly's DB2 that is connected to my NVR-4208-8P-i in smartPSS when I have 2x2 display, but not 3x3 or 4x4, I assume it is looking for a substream that is not there. Anyone have a hint as to how to get it to show up? Since the DB2 is connected outside of the NVR's private network, I...

I upgraded my readers to do the crimping, and did it while waiting on package to arrive from andy, also had time to carefully run the cable to all the locations in the eave while the soffit was off when getting a new roof, and took my time, 16 cable ends crimped with not one failing the...

I think I resolved it, I deleted the cameras, then I powered down the NVR, and even unplugged it for 10 seconds, then powered it back up and went to do a few other things to let it do it's thing... when I went back in, the cameras were auto added and were using the ports... the links go to the...

I had 2 of 6 brand new IPC-T5442TM-AS cameras show up as 37777 instead of Port3 and Port4. Interestingly, this only happened after I did the update on my brand new NVR-4208-8P-i to the latest version suggested in the NVR web interface. More detail - After initial (no pnp) setup and adding one...