Search results

Works, thanks. I did make some additions: silent and max 1 second: url="http://${ip}/cgi-bin/ptz.cgi?action=start&channel=0&code=GotoPreset&arg1=0&arg2=${preset}&arg3=0" curl --digest -u "${user}:${pass}" -s -g -m 1 -- "${url}"

Well, you may not understood the why of the question, but you surely gave the answer with that example curl command. Whether from a very formal manual, or a practical example how-to, one needs to know the syntax. Much appreciated. So, is there a proper formal manual for this sort of stuff...

hmm.. I got it pre-owned. Local equivalent of craigslist. I guess lack of traceability will work against me. Any methods to determine if it is said "hacked-to-english" model?

Hello I would like to send some control parms to the Dahua SD59225UN-HNI and SD5A225XA-HNI Specifically, I would like to disable auto-tracking at 08h00 and re-enable at 18h00, or when user presses a button if they leave everything unattended for the day. And maybe also have some hardware...

I know right? Which is why I was not worried too much when I could by this "ntsc version" for a bargain. However, whether I can replace the firmware.... I do not want to end up with a brick. So to repeat the question, anyone know if this firmware also applies to the SD59225UN-HNI

Anyone know if this also works for SD59225UN-HNI instead of SD59225U-HNI I want to be careful, but this website also directs me to the same firmware even if I enter SD59225UN-HNI And this brochure shows the difference of the N is it is a NTCS instead of PAL. To be honest, I am in a PAL country...

That "abnormal" sounded familiar, but not for me: go to first page and search for post by user epcjay. If you have the same, you may have forgot to tell us you use the web-page for NVR control. I advise to do it directly with the PC client or the android client. I would not trust the...

I have the 19 from the Chinese website, but remember, it is not made English. If you do a full factory reset, your interface would go Chinese And why would you want 19 anyway, if you are OK with running the risk if reverting to chinese, you may as well go to 21?

It is working for me on a non-HikVision camera, using OnVif driver. (a XM camera)

Even on the official Chinese website there is no update since V3.0.21 build170417, so since over a year. Its been running fine for me, in English, but I surely make sure I am never going to do a full reset. I did grab that 18 though, just in case, thanks, because the current English fallback I...

Yeah that's normal. Both red and both black are connected together to the 12V barrel connector. The Black is also connecter to the base of both Ethernet status LED's. The small connector is supposed to be on the camera board and the big one goes on the InfraRed LED board as it uses more power...

Awesome! Now lets hope with such protocol information, companies like Hikvision see their wait to include the protocol.

don't use wifi, make sure you are on the same cabled network (no routing, level 2 switch only) (edit: Also, no VMware, Wine, BootCamp and such virtual stuff.)

With the ip and reset tool for this camera, you can do a factory reset. I suspect that would also reset the password.

Often that is also called POE, but official POE is 48v DC directly into the RJ45 pins, and it needs an extra piece of electronics inside the camera. I also have two of those. What is sometimes confusing is that even those real POE camera's also have a 12V DC jack next to the RJ45, so you could...

Sorry. I actually have the exact same camera: Version: V4.02.R12.00006510.10010.1407 BuildTime: 2014-10-23 16:54:02 But I cannot test: I put that camera's on a separate non-routable VLAN segment. I can only view them indirectly through the NVR. So I cannot test the snapshot, not unless I am...

I am a bit busy now, so cannot spend too much time. But I want to warn you: there are many variant camera's, all with slightly different firmware, and if you burn the wrong one, you brick the camera. So as you are not too skilled (by your own estimates) do not burn firmware unless someone you...

Well, it works for me, and many other people also report it as working. Maybe your camera simply does not have it. but you could try adding a password, but I am not sure of the format. I would use one of these two...

http://192.168.1.10/webcapture.jpg?command=snap&channel=1 thanks to the wonderful security features, no user or password is needed.

I made that mistake once. Tape is *not* enough, no matter how many layers: RJ45 8Pin Interface Ethernet IP68 Waterproof Cable Plug Socket Wire Connector | eBay

So what you are saying is that if I use the same language flag change on the native Chinese firmware (using the same tool as for the camera firmware), it will not reset to Chinese anymore, not even after a factory reset? Did you actually try a factory reset? Are you aware of CmdrBond's warning...

Yes, it would be nice if the NVR had a ping diagnostics. Or if the camera config would report "connection timeout" instead of always "parameter error". I guess a hint is how long it takes to go to parameter error, it obviously is a timeout rather than a wrong parameter. We should check if it...

Still the wrong link, sorry. And I see I clicked on the wrong line, the 78 instead of the 71/78 Fixed the post above to ensure people do not download the wrong one. Anyway: Final links: List of firmwares Actual firmware

No, but I did grab it just in case. Building up quite the collection. Not planning to apply it because we are in business season, and all is working. Your link did not work for me. I got it from here though. Oddly, my file is labeled with 170418 in stead of 170417 ??? Can you hash the...

Well, I do not see anything wrong with your network either. Was kind of hoping you accidentally set a 252 netmask instead of a 255 one. I do wonder why you have a 1460 MTU? Why did you set that? It should not matter. I have a 1492 MTU myself, but that is because I have the camera's on a VLAN...

Are you saying the 34567 cameras worked, before changing IP? If so, that rather significant. Possibly even deserved to be mentioned on your very first post. It leads me to think of one of two possible issues: - Again a network error. What IP and subnet mask is your NVR on. Are you overlooking...

Ok, weird. Mine really work: (The one with parameter error is indeed offline) My next guesses: (sorry of they are obvious and tried already) - You really sure the password is OK? Try a password without funny characters, I had some problems with that once - Are camera and nvr on the same...

HIK camera, I have no experiance. But the fact you are unable to make a HIK camera work on a HIK NVR hints that you may have a network problem. You sure your cables and IP addresses are correct? In which case you should ignore the rest of this post. But otherwise: As to the 34567 camera's ...

Nice and true generic advise, but I was asking to know specifically about Dahua NVR and Sofia (port 34567) IPC's As mentioned, HikVision NVR and port 34567 IPC do actually work for ONVIF motion detect. Which in my view is the most important feature (other then actually getting video) Another...

How does the Dahua work with non-brand IP camera's in regard to features like motion detect? I have a small 8-channel mini NVR, of which I believe it is from the same root at Dahua (after reading the Dahua manual with schreenshots, I recognise some of them), and that device did support Onvif...