Search results

Nobody?

Nobody a Link for me?

I'm looking for a recent documentation about the API for my DS-7732NI-SP Firmware V3.4.4 Build 170526. I want to capture the streams of the cameras via HTTP and paste into a web document. Where can I find a current documentary?

it works.. I have reset to Factory.

The recorder has assigned IP and password.

I try to operate this Chinese Cam on a DS-7732NI-SP1620140411BBRR45982xxxxxxxx. There is always only detection. Is not this cam on this recorder?

Any a rollback to 5.3?

I think the Problem is the Cable on the Cam, it is fixed. Ok, thanks for Help.

I have found the error, the cam loses the connection over LAN sometimes. Therefore, the Flash is canceled. The question is, why is the connection always interrupted briefly? Software or hardware error?

I Flash all Cam in this Configuration, no Problems any Time.

It is a Laptop over a POE Switch. The File ist on c:/Downloads/

I have here a DS-2CD2032-I with firmware V5.3.0 build 150513. The S / N is DS-2CD2032F-I20150325CCWR50856xxxx. There is no firmware update to 5.3.3 or 5.4.0. I could update the cam from IPC_R0_EN_STD_5.2.3_141024 to IPC_R0_EN_STD_5.3.0_150513 via the WEB GUI. More is not possible. In the log I...

No Way, I Need a Rollback...

Fu... it was flashed an R0. I have flash IPC_R6_EN_STD_5.4.5_170124 the Cam hangs in the web GUI and no Picture. From the factory was the IPC_R6_EN_STD_5.3.3_150630. I need an Downgrad to 5.3. Is there what?

Is it an RO or R6? I find the cam with both in the listing.

And a downgrad to an early Version with SSH? Do you have any other ideas? Maybe a memory chip? Is there another command to limit the error?

is there no more SSH in the 5.4 or is it not displayed with me?

The camera has worked. What caused the problem is I can not say. Can one somehow still an error log write to let to see why the camera reboots and no picture shows.

Yes. I have make a downgrad to 5.2.2 (Custom Firmware Downgrader 5.3.0 Chinese to 5.2.5 English), then the enhanced_mtd_hack (Custom Firmware Downgrader 5.3.0 Chinese to 5.2.5 English), than is the Cam in EN. It is a little tricky, it must first understand,this is not for normal user. Then over...

I have a 2CD-2342WD-i here. If I have the camera boats it is inactiv. I forgive the password, it is booting. In the web interface I have no picture, some settings are not possible. After some time, it booted itself by itself new and has no password and no assigned IP more. What could be the problem?

Thanks, now I understand it. @alastairstevenson many thanks

Thank you, it runs again.

so, now I made the changes and from 0x09 to 0xFC, that must be 244. Then calculate the checksum. Does it look better now? What happens if the checksum is wrong and I copy it back to the cam? Copy to the cam bit the command (cp /mnt/nfs00/mtdblock6 /dev), then overwrites the original file? Do I...

In a other Tread I have found " Select 0xF4 (244) bytes from ...." in the Picture are 0xF4 Bytes? Then is the calculated Checksum 0D01. If that is correct, then why is in the original file by 0x04 and 0x05 E4 0B. Sorry, I just do not understand it

Sorry, I have to translate this into German everything, so some things is not to be understood correctly. I did not quite understand this with the Checksum. I put the cursor before offset 09 and let me display the checksum? I do not understand exactly where the value of the 0xF4 bytes ist. Start...

ok, I understand that correctly. I have installed The cam boot in Minisystem. I hack it with the "enhanced mtd hack" to EN. How flash the 5.3.0 on the Cam? About TFTP? Do I boot the cam with the 5.3.0 .dav File, reboot, than the 5.4.0 ->5.4.5 all behind each other over TFTP?

I thought you always had to come to exactly the checksum you had before the change. I know the bios adjust for wlan module with hp.

I have Flash the Customer EN from Second Link and the Language is in Chines. I have Check the CN File with Tool and the Language is 02 inside.

I am now sitting 3 hours at the camera. had downgraded to 5.2.5 CH, since she ran into Chinese. After that I installed digicap_brickfix540_EN, camera booted in the Minisystem. Have then upgrade to DS-2xx2_5.4.5_170123 made. Cam has bootloop. What was wrong now?

a question about checksum Before I change the original mtdblock6 hav it checksum 16 FD24 I change 0x10 to 0x01 for EN 0x64 to 0x07 0x65 to 0x98 for devType = 38919 Then is the Checksum FC2B Is it true that I must have the checksume FD24 again after the changes?