Search results

research the owners of the four seasons gardening center you might get a surprise

Try some spray lube and a powerful little neodymium magnet

Just installed one at work I had laying around Have you tried up the coax setting UTC I will screen shot the settings when in work tomorrow And get back to you

What I do for these little cameras I have five around the house My first thing is add it to iVMS usually get the older version as some of the new versions have problems with video out put on certain computers Add the camera using admin and the password would be admin+ the verification code...

passive mics and active mics, search box top right this has been documented a few times

5.6.0 i dare you

Lol friends have been asking about these Arlo packages they can buy to protect there workshops My response is full fenderman style ;)

5.5.71 is the latest for that ptz dome

Turn on the sub stream audio and video

Try turning off capture on the camera web GUI see if that fixes your problem

I always manually update if there’s a need this auto upgrade could get some one unstuck ,It just seemed to help the un savvy end user ( or unstick as pointed out the grey market user who knows what there objective is

I normally go to the nvr and on group open the box which shows what cameras are connected then tap open the blue square which says modify That then brings up another box with the camera and six lines down is stream key

Ok on your phone Hik-Connect you can disable it there They will txt you a code just enter it,then encryption should be disabled

There I was thinking there making life easier for the not so tech savvy users lol

Have a look and see if stream encryption is on That photo with the blank boxes hit the modify button and if it shows steam encryption key type in the key that is usually the verification code on the bottom of the nvr “ example GHVYNH”

Search top right for Europe portal Navigate to front ends look, for ptz it’s the r7 platform 5.5.71 but don’t jump straight to that one,implement each firmware upgrade one at a time

I am assuming you have activated the camera via sadap and it gave you the 192.168.1.106 ip is dhcp now off,untick the box And the password you set was the same as the nvrs.? Go to camera management and manually add the camera, not plug and play. Click on modify enter the IP address Then admin...

Can you hit the rest button and see what it goes back to

admin adminQGFYCU Then hit add camera in iVMS in the computer The firm ware is 5.5.4 for this camera on the Europe web site under the consumer camera section

You should have a box full of red squares It looks like you haven’t drawn the area

Time to move over to Andy @EMPIRETECANDY

192.0.0.64 i think its in the mini boot load up mode due to a firmware issue

Save your self some time and learn about a VPN connection Hik-Connect will require you to turn on upnp and port forwarding,and that’s not recommended They have a p2p on some firmware which doesn’t require any port forwarding Just the correct 8.8.8.8 or 8.8.4.4 Been down this road before,and...

You are aware it’s only a 4x zoom When stock was available for $720 you could buy the 20x zoom

no i haven't used this supplier seems cheaper than some other aussie suppliers

Hi Dave welcome on board I am on the other side of town where the big hole filled with gold is lol

I’m on line so if you run into bother shout out

This IP address you can not load in to a browser it will not work this way On your phone app it will work If you add this to a nvr channel under manually then you can see it For all settings click on the camera with remote management and all the settings will open up for you

Navigate to security and untick illegal log in and save Navigate to user and modify the password to what you want hit save Then in device manager delete the camera it will be back to the not added bottom part Re add the camera this time admin Your new password Then it should add with...

Next take a cable and plug into a switch or the router. Go to you computer and open up iVMS Go to device management and look for the camera it should say it not added Click on add device Give the camera a name Then type admin Then for the password use admin(your device code which is under the...