Search results

on the Microseven M7WP-MIC, is there continuity between the 12v ground and the audio ground? if this is the case, it may be possible that any power adapter you use might inject noise into the audio signal due to the power adapter design. even worse, any noise on your AC line may pass through...

what does "the maximum hdd capacity varies with environment temperature" mean? looking up the hdd specs for my NVR4104/4108-P-4KS2... 1 SATA III port, up to 10 TB for a single HDD. The maximum HDD capacity varies with environment temperature thinking of getting a 10tb western...

i have an issue with the DMSS app that if i search previously recorded video and try to record it on my phone using the app, the DMSS app will only alow about one and a half minutes to be recorded. i tried to update the firmware on my NVR4108...

now with the latest version of the app, when i try to record video in the app, it only saves about one and a half minutes worth, even if i have it recording for five minutes.

didn't help.

i have audio NR off on my cams. if you go to "me" then "setting" on the dmss app, NR is there.

so far, when i playback my cams or cams from a friends house in another city over my wifi here, the app works properly. if i use the cellular data and not wifi, playback stutters. it's strange because my data speeds are faster than my home internet speeds. my cellular data speed is 114Mb down...

i really wish they just kept updating gDMSS plus. the only thing i found wrong with that app was the playback didn't work. i find the ptz on DMSS is slow to respond and some of the buttons don't respond to your finger press on the screen and you have to hit them a few times. i also really wish...

did they release an update? i'm on version 1.96.002 build date 2021.11.25 i does seem to work properly at the moment.

anyone having playback (playback of recording) issues with the DMSS android app? (live playback is fine) when i first install the app, the playback works ok for a bit then it gets screwy when i try to use it later on after using it a couple of times. when i click on a camera, click on playback...

i changed back to h264.h and am using CBR. should i use h.264 or h.264h ? what bitrate should i use for 15fps 1080p?

i have disabled WDR for night. cameras are using smartIR do you recommend against using h.265? i had just switched all my cameras over today. pretty much using highest bitrate shown, VBR level 6. also, what is the next interval up from 8.3ms for the shutter speed? 8.3ms seems a tad bit dark...

though i got WDR working by making the settings in internet explorer, WDR doesn't work while in in black and white mode at night when IR is on. this must be by design?

gives a slightly darker image. but im guessing movement will be picked up less blurry?

wittaj, that is a very informative reply. have changed my main stream settings to: h.265 smart codec off 1080p 15fps vbr quality 6 4096 max bitrate iframe 15 for conditions: wdr is set to 4 for day and night exposure mode is set to auto but maybe i should put it at shutter priority 1/60 for...

that worked. i wonder what other settings were not applied because i didn't use IE? p.s, is it normal to have your fps limited to 30 when using WDR?

i did a factory reset, updated the firmware, did a factory reset again. the WDR still doesn't work. they must have broke it in a firmware update a while back. doesn't work on any of my cameras, confirmed with version V2.800.0000015.0.R, Build Date: 2020-04-30 or later. i wonder with which...

in NVR settings/cameras, what does the H.265 auto switch setting do?

anybody notice that IPC-HDW5231R-ZE with firmware V2.800.0000015.0.R, Build Date: 2020-04-30 the WDR setting does nothing anymore? BLC and HLC work but not WDR. i'm having this issue on multiple cameras at different sites, even with IPC-HDW4231EM-ASE cameras. is this a known issue? also...

anybody notice that with V2.800.0000015.0.R, Build Date: 2020-04-30, the WDR setting does nothing?

ok, i managed to transfer the update.img to the ipcam. i go to 192.168.1.108 and i can see it has dahua firmware now. so it was a success only issue is i can't login to the camera with username: admin and password: admin i even tried password 1234, 888888, 88888888, my old password, etc...

host is alive. pc firewall and antivirus is disabled. the camera is not pingable at 192.168.1.108 or visible on the network but that is because i am connected to it via serial i am guessing. camera is also connected by ethernet. am i supposed to be using any specific version of tftp? i am...

i get the following error in putty: run up Using ambarella mac device TFTP from server 192.168.1.214; our IP address is 192.168.1.108 Download Filename 'update.img'. Download to address: 0x2000000 Downloading: * TFTP error: (0)>

this is the text i got from printenv >printenv bootargs=console=ttyS0,115200 mem=110M root=/dev/mtdblock5 rootfstype=squashfs init=/linuxrc bootcmd=sf read 0x200100 0x8000 0x8000;sf read 0x2000000 0xf0000 0x180000;bootm 0x2000000 bootdelay=3 baudrate=115200 ipaddr=192.168.1.108...

ok. that worked. when i did printenv i got a bunch of text print out on the screen. when i do "run up", it's says "link down". i have the update.img file on my desktop. is update.img supposed to be in a certain location? in the folder that is called "update.img" that is created when i...

ok, i soldered the wires on, opened putty and saw the writing update on the screen so i must have connected the wires correctly. now what do i do? i try typing on the open terminal window "printenv" but no text shows on the screen as if im not typing anything.

so first i flash with update.img through the wires i will solder to the camera pcb using putty then go to web interface and update with DH_IPC-HX1X2X-Themis_EngSpnFrn_N_V2.600.0005.0.R.20170527.bin ?

i want to use this firmware: https://dahuawiki.com/images/Files/Firmware/DH_IPC-HX1X2X-Themis_EngSpnFrn_N_V2.600.0005.0.R.20170527.bin so rename it to update.img ? what do you mean by updating each module?

i may be able to solder some wires in there. what is the procedure to upgrade? i want to make sure i understand it before i proceed with the soldering.

the 2.54mm pitch connectors i have are too thick for the holes and spaced too far apart. the holes are too close. i couldn't even hold the pins from the jumper wires i have because they were too bulky.