Search results

current settings. What should they be set to?

Ok I was able to figure it out thanks to another user @catcamstar posted the following. See the photo as I saved it as a screenshot. Basically you go into your settings>system>storage tab and tell it to record or save the intelligent recordings for whatever channel you’re wanting. I only want...

yes on the NVR itself I can see the IVS triggered events just not on the app

Any updates to this? I seem to have the same issue when trying to filter my LPR during the daytime since setting up IVS rules.

More samples with the help of @bigredfish

Ok guess I got confused by the part number change. Thanks!

Hate to dig up an old thread but hey I searched…. I have one of the HFW5241E-Z12E’s and a friend of mine would like to get one for his house. Where might one pick another one up? Is there a better version that’s basically the same?

Ignore the cables as I ran out of zip ties for the moment but she’s hung! Still have to adjust the cameras some but I’m finally on the final stretch

I don’t have studs on the piece I’m screwing into though. The span is too short and the only studs are in the corners. Weight of the NVR is close to 10 pounds

where did you get that mount? I am wanting to do the same in my closet. Also, are you mounted in a stud or just using wall anchors?

Took the NVR to work and a co-worker is creating me some wall mounts for it. Looks a bit overkill but I guess he doesn’t want it to fall :)

I don’t know for sure but it seems like they would fit in a junction box

originally in the wall, but I’ve scrapped the BNC setup and just finished pulling cat6 cables to each camera and will go with Poe

Major update for anyone still reading and may care. I was able to finish the pulls tonight basically solo as my wife had errands to run and couldn’t help. I’m thankful for the help and the push to get these done! Not finished but the hard part is done and just have to finish the ends.

Ok small update. I pulled 2 more cables tonight making it 3-3 for the cat6 swap. Have 3 more to go with one being super easy, and 2 harder ones. one question for you guys. Pulling the harder ones, do I pull from the outside into the closet, or from the closet to the outside? Does it matter? I’m...

Originally it was but I upgraded the cable when I installed them. Lesson learned I guess but now I get to try and pull new cable before the summer heat hits!

These were the connectors

I’m not exactly sure. It would work sporadically which was throwing me off. I used this when I had the analog system

I bought a box of vertical cable cat6 plenum reasonably cheap on eBay. Thank you all for the help and support!

thank you for taking the time out of your day and trying to help me! Not anyone’s fault except the cable I guess didn’t want to cooperate

Ok so after many trials and error @bigredfish and I came to the conclusions that my current wire will not work. Unfortunately I am going to have to pull new wire and hope for the best. I have one half of a run so far but have a question for you guys. The box of cat6 I’m using is in the attic...

my apologies. Thanks for the response

Ok for another test could I plug in the 12v connector I have at the cameras location? I still have those ran when I used the analog cameras. would the Poe know that it only needs the signal and not the power? Would I mess something up trying that external power? edit: I took the camera back...

sorry I was testing the first adaptive camera which is port 3. Port 1 is my LPR camera which I ended up running cat6 and connects just fine. Camera 2 I can’t reach so right now is on pause

my cable and connectors are 75 ohm

I tried resetting the camera in port 3 and doesn’t do anything. I can see in the Poe screen it has its current wattage consumption though.

This is what I followed when ordering. 1st example https://images.app.goo.gl/RaFK6e4XKSMsX5LS7

sorry I guess I got caught up with the lingo. I saw a post about keeping my rg59 cable and using ip cameras via epoe. I then bought a NVR and those LR1002’s for each run. Did I buy something I don’t need?

Just for testing purposes could I plug them back into port 1 and see if they appear? Guess I couldn’t reset them that way as I wouldn’t keep them in that port