DAHUA IPC-HDBW4231F-AS Bootloop

PinguMx · Sep 18, 2024

Hello all,

I have a Dahua camera that went into a boot loop after a firmware upgrade. I tried flashing the firmware via the serial port using the TFTP method, but had no luck.

I flashed the firmware DH_IPC-HX5X3X-Rhea_MultiLang_NP_Stream3_V2.800.0000029.0.R.221220, but I’m not sure if it’s the correct one for this camera (I can’t find it online). The camera was bought in Europe, so it shouldn’t be a Chinese model.

From the log on the serial port, I see that a segmentation fault caused the boot loop, but I’m unsure what led to the segfault.

Does anyone have any hints on what the issue could be? Could it be the wrong firmware?

Serial log attached.

▒
U-Boot 2010.06-svn6390 (Feb 19 2020 - 12:04:41)
I2C: ready
DRAM: 118 MiB
gBootLogPtr:00b80008.
spinor flash ID is 0x1940ef
partition file version 2
rootfstype squashfs root /dev/mtdblock5
gParameter[0]:node=bootargs, parameter=console=ttyS0,115200 mem=116M root=/dev/m tdblock5 rootfstype=squashfs init=/linuxrc.
TEXT_BASE:01000000
Net: PHY:0x001cc816,addr:0x00
s3l phy RTL8201 init

partition file version 2
rootfstype squashfs root /dev/mtdblock5
MMC: sdmmc init
Using ambarella mac device
Download Filename 'upgrade_info_7db780a713a4.txt'.
Downloading: *
Retry count exceeded; starting again
Try again use backup_serverip
*** ERROR: `serverip' not set
Failed to get info.txt
Fail to get info file!
Init error!
Using ambarella mac device
Download Filename 'failed.txt'.
Downloading: *
Retry count exceeded; starting again
Support backupVer:255
state:ff,err_count:04
Adjust Memory Allocation, dram_size=0x7400000, dsp_ram.start=0x7600000, dsp_ram.size=0x8a00000
fail to load bootargsParameters.txt
fail to load bootargsParameters.txt file
hmagic=0xffffffff
Before write boot backup version page, it should be erased!!!
SPI probe: 32768 KiB W25Q256FV at 0:0 is now current device
Wrong Image Format for bootm command
ERROR: can't get kernel image!
try:kload 0x2000000 succeed!
Verifying Checksum ... OK
partition file version 2
rootfstype squashfs root /dev/mtdblock5
curVer:V1.4 <= newVer:V2.0,verCompare success!
UBOOT_commonSwRsaVerify run successfully!
Loading Kernel Image ...OK
OK
partition file version 2
rootfstype squashfs root /dev/mtdblock5
fail to load bootargsParameters.txt
fail to load bootargsParameters.txt file
Adjust Memory Allocation, dram_size=0x7400000, dsp_ram.start=0x7600000, dsp_ram.size=0x8a00000
crashflasg:1, logmagic:54410011.

Starting kernel ...
partition file version 2
rootfstype squashfs root /dev/mtdblock5
half-boot found, check bst
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpu
Linux version 3.10.73 (jenkins@centos235) (gcc version 5.2.1 20151005 (Linaro GCC 5.2-2015.11-2) ) #2 PREEMPT Mon Mar 30 19:28:42 CST 2020
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Ambarella S3L (Flattened Device Tree), model: Ambarella S3L Olive Board
os ----- 200000 , 7400000
logmem start:757e000, size:80000.
network type:1.
init gLogRamRes: start=0x757e000;size=0x80000
Memory policy: ECC disabled, Data cache writeback
Ambarella: AHB = 0xe0000000[0xe0000000],0x01000000 0
Ambarella: APB = 0xe8000000[0xe8000000],0x01000000 0
Ambarella: PPM = 0x00000000[0xdfe00000],0x00200000 9
Ambarella: AXI = 0xf0000000[0xf0000000],0x00030000 0
Ambarella: DRAMC = 0xdffe0000[0xef000000],0x00020000 0
Ambarella: DBGBUS = 0xec000000[0xec000000],0x00200000 0
Ambarella: DBGFMEM = 0xee000000[0xee000000],0x01000000 0
Ambarella: IAVMEM = 0x07600000[ ],0x08a00000
Ambarella: FBMEM = 0x00000000[ ],0x00000000
CPU: All CPU(s) started in SVC mode.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 29464
Kernel command line: console=ttyS0,115200 mem=116M root=/dev/mtdblock5 rootfstype=squashfs init=/linuxrc
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 116MB = 116MB total
Memory: 112860k/112860k available, 5924k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0x87800000 - 0xff000000 (1912 MB)
lowmem : 0x80000000 - 0x87400000 ( 116 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x803b6e08 (3772 kB)
.init : 0x803b7000 - 0x803d3504 ( 114 kB)
.data : 0x803d4000 - 0x803feca0 ( 172 kB)
.bss : 0x803feca0 - 0x80423538 ( 147 kB)
NR_IRQS:240
sched_clock: 32 bits at 90MHz, resolution 11ns, wraps every 47721ms
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 812.64 BogoMIPS (lpj=4063232)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x802d44b0 - 0x802d44f4
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
L310 cache controller enabled
l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32020000, Cache size: 131072 B
ambarella-pinctrl e8009000.pinctrl: Ambarella pinctrl driver registered
ambarella-gpio gpio.0: Ambarella GPIO driver registered
bio: create slab <bio-0> at 0
ambarella-dma e0005000.dma: Ambarella DMA Engine
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource ambarella-cs-timer
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 220
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
e8005000.uart: ttyS0 at MMIO 0xe8005000 (irq = 61) is a ambuart
ambarella-uart e0032000.uart: Serial[1] use txdma
ambarella-uart e0032000.uart: Serial[1] use rxdma
e0032000.uart: ttyS1 at MMIO 0xe0032000 (irq = 80) is a ambuart
Ambarella read-only mtdblock
mtd .name = amba_spinor, .size = 0x2000000 (32MiB) .erasesize = 0x00010000 (64KiB) .numeraseregions = 0
16 ofpart partitions found on MTD device amba_spinor
Creating 16 MTD partitions on "amba_spinor":
0x000000000000-0x000000040000 : "MinBoot"
0x000000080000-0x0000000c0000 : "U-Boot"
0x0000000c0000-0x0000000e0000 : "hwid"
0x0000000e0000-0x0000000f0000 : "partition"
0x000001040000-0x000001200000 : "Kernel"
0x000001b80000-0x000001fd0000 : "romfs"
0x000001200000-0x000001880000 : "web"
0x0000000f0000-0x000001000000 : "user"
0x000001a70000-0x000001aa0000 : "updateflag"
0x000001aa0000-0x000001b10000 : "config"
0x000001880000-0x0000018a0000 : "product"
0x0000018a0000-0x000001970000 : "custom"
0x000001000000-0x000001040000 : "half-boot"
0x000001b10000-0x000001b80000 : "backup"
0x000001970000-0x000001a70000 : "data"
0x000001fd0000-0x000002000000 : "dgs"
winbond flash, rdsr3:e0
SPI NOR Controller probed
PPP generic driver version 2.4.2
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-ambarella: AMBARELLA-EHCI Host Controller driver
ambarella-ehci e0018000.ehci: EHCI Host Controller
ambarella-ehci e0018000.ehci: new USB bus registered, assigned bus number 1
ambarella-ehci e0018000.ehci: irq 66, io mem 0xe0018000
ambarella-ehci e0018000.ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.10.73 ehci_hcd
usb usb1: SerialNumber: AmbUSB
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1763 buckets, 7052 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
ThumbEE CPU extension supported.
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
devtmpfs: mounted
Freeing unused kernel memory: 112K (803b7000 - 803d3000)

mount: mounting /dev/mtdblock10 on /mnt/pd/ failed: Invalid argument
dh_keyboard:0
touch: /mnt/mtd/Config/ppp/pppoe-enable: No space left on device
touch: /mnt/mtd/Config/ppp/pap-secrets: No space left on device
touch: /mnt/mtd/Config/ppp/pppoesessionctx: No space left on device
touch: /mnt/mtd/Config/ppp/pppoe-redial_time: No space left on device
touch: /mnt/mtd/Config/dial-ip: No space left on device
libphy: Ambarella MII Bus: probed
ambarella-eth e000e000.ethernet: Ethernet PHY[0]: 0x001cc816!

[OSA-DRV] OSA Build on Apr 16 2019 at 00:50:27.
[OSA-DRV] SVN NUM: 21764.

[OSA-DRV] Char device create OK !

[OSA-DRV] Monitor Task pid=110 tid=110

[LOG-DRV] LOG Build on Apr 24 2019 at 08:02:09.
[LOG-DRV] SVN NUM: 16867.

[LOG-DRV] ramStart:0x757e000;ramSize:0x80000;select:1
[LOG-DRV] ramStart:0x87383000;ramSize:0x80000;select:1
[OSA-DRV] Char device create OK !
[LOG-DRV] coreId = 0, logLevel = 2
[LOG-DRV] coreId = 1, logLevel = 2
[LOG-DRV] coreId = 2, logLevel = 2
[LOG-DRV] coreId = 3, logLevel = 2
[LOG-DRV] coreId = 4, logLevel = 2
[LOG-DRV] coreId = 5, logLevel = 2
00:00:01|[DH_Binder] Binder.ko Build on Apr 17 2019 at 11:57:05.
00:00:01|[DH_Binder] SVN NUM: 4577.

00:00:01|[DH_Binder] NameServer Initial OK !
00:00:01|[DH_Binder] Create binder memory pool(size:1044480) OK!
00:00:01|[DH_Binder] Create binder memory pool(size:1044480) OK!
00:00:01|[DH_Binder] Binder Initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[DH_Binder] SR driver initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[DH_Binder] NS driver initial OK !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[DH_Binder] Binder driver initial OK !
00:00:01|[SPF] SPF Build on Apr 19 2019 at 01:49:51.
00:00:01|[SPF] SVN NUM: 16926.

00:00:01|[SPF] SIL initial OK !
00:00:01|[SPF] SPF initial ok !
00:00:01|[OSA-DRV] Char device create OK !
00:00:01|[SPF] SPF Proc Create OK!!!
00:00:01|[SPF] SPF driver initial ok !
00:00:01|[prc] PRC Driver Build on Feb 22 2019 at 01:42:21.
00:00:01|[prc] SVN NUM: 20335.

00:00:01|[prc] Start to init module!
00:00:01|[SPF] Dai 2 register OK !
00:00:01|[prc] Success to init module!
00:00:02|[pdc]

PDC Build on Apr 25 2019 at 01:11:21.
00:00:02|[pdc] SVN NUM: 11361.

00:00:02|[pdc] BASE_LINE: 240
00:00:02|[pdc] OSA_kProcCreate OK
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] PDC_PartionInit ok!!
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] defog = 0
00:00:02|[pdc] binderFlag: 0x3, funcap: 0x18538b,0x1070a00,0x0,0x0
00:00:02|[pdc] videoOut Channel is 0
00:00:02|[pdc] Find Product: IPC-HDBW4231F-AS.
00:00:02|[pdc] Config size 8296 !
00:00:02|[pdc] SenCfg not match
00:00:02|[pdc] SenExtCfg Match OK,pExtCfgParams->pCfg: 7f1afbec
00:00:02|[pdc] SenCfgSize: 0 Bytes
00:00:02|[pdc] SenExtCfgSize: 864 Bytes
00:00:02|[pdc] Init spiBus0 Successed!
00:00:02|[pdc] Init spiBus2 Successed!
00:00:02|[pdc] Init I2CBus0 Successed!
00:00:02|[pdc] Init I2CBus3 Successed!
00:00:02|[pdc] PDC_MODULE_RESET_STATE
00:00:02|[pdc] Reboot system counter 1!
00:00:02|[pdc] ircut types = [1]
00:00:02|[pdc] ircut types = [5]
00:00:02|[pdc] ircut types = [6]
00:00:02|[pdc] ircut types = [7]
00:00:02|[pdc] ircut types = [8]
00:00:02|[pdc] ircut types = [2]
00:00:02|[pdc] ircut[0] = 1
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] PDC_pinInit As Usual!
00:00:02|[pdc] Get reset pin: 22 OK !
00:00:02|[pdc] Get comPort Cfg ok changeGio=65535 !0sa
00:00:02|[pdc] PDC_comInit OK!
00:00:02|[pdc] codecMask 00000080
00:00:02|[SPF] codecType 128 register OK !
00:00:02|[pdc] NAU8810 Proc Add File ok!
00:00:02|[pdc] In pdc: 0x2
00:00:02|[SPF] Set logicChn OK !
00:00:02|[pdc] Try RtcDev: SocRtc
00:00:02|[prc] PRC_rtcCreate OK
00:00:02|[pdc] phyaddr = 75fe000, memLen = 2000
00:00:02|[pdc] DDRdata crc incorrect, Load from sramFile
00:00:02|[pdc] phyaddr = 75fe000, memLen = 2000
00:00:02|[pdc] DDRdata crc incorrect, Load from sramFile
00:00:02|[pdc] A B OK
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[pdc] ERROR (SRAM_writeFile|492): SRAM_writeFile failed
00:00:02|[pdc] ERROR (SRAM_fileCopy|1202): SRAM_writeFile: failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[pdc] ERROR (SRAM_writeFile|492): SRAM_writeFile failed
00:00:02|[pdc] ERROR (SRAM_fileCopy|1202): SRAM_writeFile: failed!
00:00:02|[pdc] ERROR (SOC_sramFilesSync|424): SOC_sramFilesSync Fail
00:00:02|[pdc] ERROR (SOC_check|460): SOC_sramFilesSync Fail
00:00:02|[pdc] ERROR (PDC_rtcInit|1089): Can't get the rtc 5 !
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] OSA_kProcAddFile

dcRtc OK!
00:00:02|[pdc] smartIr light count:1
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] OSA_kProcAddFile

dcKey OK!
00:00:02|[pdc] key num = 1
00:00:02|[pdc] PDC_MODULE_SENSOREXT
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] SramFile init ok !
00:00:02|[pdc] Both of Chief and Backup File CRC check OK!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:02|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:02|[pdc] ERROR (SRAM_writeFile|492): SRAM_writeFile failed
00:00:02|[pdc] ERROR (PDC_sramWrite|1583): SRAM_writeFile: write chief failed!
00:00:02|[pdc] ERROR (PDC_recordInit|895): Fail to write record!
00:00:02|[OSA-DRV] Char device create OK !
00:00:02|[pdc] ERROR (PDC_drvInit|209): PDC Driver Initial Failed !
00:00:03|[pdc] FlashTotalSize = 0x2000000
00:00:03|[pdc] The cmd 3221510149 is invalid
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:03|[pdc] Both of Chief and Backup File CRC check OK!
00:00:03|[pdc] SramFile_devRelease OK!
CATEGORY = 2
IPC Device
insmod: can't insert '/usr/lib/modules/crypt.ko': unknown symbol in module, or unknown parameter

[OSA-APP] OSA Build on Apr 16 2019 at 00:50:18.
[OSA-APP] SVN NUM: 21632.

[libpdi] libpdi.so Build on Nov 9 2019 at 09:12:10.
[libpdi] SVN NUM: 68279.
[libpdi] PDI product has 1 configs!!!
[libpdi] Sensor has 1 sensor(s)
[libpdi] PDI product Init OK!
[libpdi] PDI hwid Get OK!
net eth0: adv: sym 1, asym: 1
[libpdnet eth0: lp: sym: 0, asym: 0
i] PDI run in netinit
[libpdi] partionNum=16
[libpdi] Get fpga upgrade cfg failed, use default
00:00:03|[pdc] FlashTotalSize = 0x2000000
00:00:03|[pdc] The cmd 3221510149 is invalid
[libpdi] Get bootsupportswitchpart failed.
[libpdi] Support backup partition !!!
[libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000
[libpdi] gFlashCtrlObj.isSupportSwitchPart:0
[libpdi] gFlashCtrlObj.bootFromBack:0
[libpdi] gFlashCtrlObj.bootVersion:2
[libpdi] WARN : Device has no crypt chip!
[libpdi] ERROR (PDI_recordInit|282): Record device is not exists
[libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
[libpdi] phyaddr= 0x75fe000, memLen= 0x2000
00:00:03|[pdc] Both of Chief and Backup File CRC check OK!
[libpdi] Can't open /dev/pdcMcu
[libpdi] PDI_mcuCreate fail
[libpdi] can't find commLen cfg
[libpdi] PDI run in netinit
[libpdi] PDI_eventInit Wrapper OK!!!
[libpdi] run with no coprocessor!
[libpdi] PDI run in netinit
[libpdi] PDI_notifyInit Wrapper OK!!!

[Systools]: Build on Apr 17 2019 at 12:03:37.
[Systools]:SVN NUM: 60434.

init eth0 to default
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[pdc] ERROR (SRAM_writeFile|492): SRAM_writeFile failed
00:00:03|[pdc] ERROR (PDC_sramWrite|1583): SRAM_writeFile: write chief failed!
00:00:03|[pdc] ERROR (SramFile_devIoctl|2026): ioctl : PDC_sramWrite failed !
00:00:03|[libpdi] ERROR (PDI_sramFileWrite|162): Fail to PDI_sramFileWrite!
00:00:03|[libpdi] ERROR (PDI_setFlieFlag|199): PDI_sramFileWrite failed !
00:00:03|[libpdi] ERROR (NET_disableRoute|5312): PDI_setFlieFlag failed
00:00:03|[libpdi] set eth0 as defaultEth
IP: <192.168.1.108> netmask: <255.255.255.0>
phyAddr=0x0
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
00:00:03|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:03|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:03|[libpdi] ERROR (SaveEthAttrInFile|1705): Fail to write ip paramenters
00:00:03|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:03|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:03|[libpdi] ERROR (SaveEthAttrInFile|1705): Fail to write ip paramenters
netinit uses obsolete (PF_INET,SOCK_PACKET)
Gateway: <192.168.1.1>
00:00:03|[libpdi] SetGateWay success
00:00:03|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:03|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:03|[libpdi] ERROR (SaveEthAttrInFile|1705): Fail to write ip paramenters
00:00:03|[libpdi] hMcu is null
00:00:03|[pdc] SramFile_devRelease OK!

[OSA-APP] OSA Build on Apr 16 2019 at 00:50:18.
[OSA-APP] SVN NUM: 21632.

[libpdi] libpdi.so Build on Nov 9 2019 at 09:12:10.
[libpdi] SVN NUM: 68279.
[libpdi] PDI product has 1 configs!!!
[libpdi] Sensor has 1 sensor(s)
[libpdi] PDI product Init OK!
[libpdi] PDI hwid Get OK!
[libpdi] PDI run in netinit6
[libpdi] partionNum=16
[libpdi] Get fpga upgrade cfg failed, use default
00:00:03|[pdc] FlashTotalSize = 0x2000000
00:00:03|[pdc] The cmd 3221510149 is invalid
[libpdi] Get bootsupportswitchpart failed.
[libpdi] Support backup partition !!!
[libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000
[libpdi] gFlashCtrlObj.isSupportSwitchPart:0
[libpdi] gFlashCtrlObj.bootFromBack:0
[libpdi] gFlashCtrlObj.bootVersion:2
[libpdi] WARN : Device has no crypt chip!
[libpdi] ERROR (PDI_recordInit|282): Record device is not exists
[libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
[libpdi] phyaddr= 0x75fe000, memLen= 0x2000
00:00:03|[pdc] Both of Chief and Backup File CRC check OK!
[libpdi] Can't open /dev/pdcMcu
[libpdi] PDI_mcuCreate fail
[libpdi] can't find commLen cfg
[libpdi] PDI run in netinit6
[libpdi] PDI_eventInit Wrapper OK!!!
[libpdi] run with no coprocessor!
[libpdi] PDI run in netinit6
[libpdi] PDI_notifyInit Wrapper OK!!!

[Systools]: Build on Apr 17 2019 at 12:03:37.
[Systools]:SVN NUM: 60434.

IPV6: only init eth0
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[OSA-DRV] ERROR (OSA_fileWrite|605): write failed, ret:-28
00:00:03|[pdc] ERROR (SRAM_writeFile|456): OSA_fileWrite: len = -1 failed!
00:00:03|[pdc] ERROR (SRAM_writeFile|492): SRAM_writeFile failed
00:00:03|[pdc] ERROR (PDC_sramWrite|1583): SRAM_writeFile: write chief failed!
00:00:03|[pdc] ERROR (SramFile_devIoctl|2026): ioctl : PDC_sramWrite failed !
00:00:03|[libpdi] ERROR (PDI_sramFileWrite|162): Fail to PDI_sramFileWrite!
00:00:03|[libpdi] ERROR (PDI_setFlieFlag|199): PDI_sramFileWrite failed !
00:00:03|[libpdi] ERROR (NET_disableRoute|5312): PDI_setFlieFlag failed
"netinit6 help" for help
eth0:
MAC: <3c:ef:8c:f0:74:a0>
00:00:03|[libpdi] hMcu is null
00:00:03|[pdc] SramFile_devRelease OK!

[OSA-APP] OSA Build on Apr 16 2019 at 00:50:18.
[OSA-APP] SVN NUM: 21632.

[libpdi] libpdi.so Build on Nov 9 2019 at 09:12:10.
[libpdi] SVN NUM: 68279.
[libpdi] PDI product has 1 configs!!!
[libpdi] Sensor has 1 sensor(s)
[libpdi] PDI product Init OK!
[libpdi] PDI hwid Get OK!
[libpdi] PDI run in syshelper
[libpdi] partionNum=16
[libpdi] Get fpga upgrade cfg failed, use default
00:00:03|[pdc] FlashTotalSize = 0x2000000
00:00:03|[pdc] The cmd 3221510149 is invalid
[libpdi] Get bootsupportswitchpart failed.
[libpdi] Support backup partition !!!
[libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000
[libpdi] gFlashCtrlObj.isSupportSwitchPart:0
[libpdi] gFlashCtrlObj.bootFromBack:0
[libpdi] gFlashCtrlObj.bootVersion:2
[libpdi] WARN : Device has no crypt chip!
[libpdi] ERROR (PDI_recordInit|282): Record device is not exists
[libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:03|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
[libpdi] phyaddr= 0x75fe000, memLen= 0x2000
00:00:03|[pdc] Both of Chief and Backup File CRC check OK!
[libpdi] Can't open /dev/pdcMcu
[libpdi] PDI_mcuCreate fail
00:00:03|[SEN-DRV] Sensor Build on Apr 19 2019 at 05:42:16.
00:00:03|[SEN-DRV] SVN NUM: 21615.

00:00:03|[SEN-DRV] pInfo->nAdjSensorNum=3
00:00:03|[SEN-DRV] pObj->sensorType= 74
00:00:03|[SEN-DRV] call SEN_drvCoreGetClkSrcObj(2, 0)
[libpdi] can't find commLen cfg
[libpdi] PDI run in syshelper
[libpdi] PDI_eventInit Wrapper OK!!!
[libpdi] run with no coprocessor!
[libpdi] PDI run in syshelper
[libpdi] PDI_notifyInit Wrapper OK!!!

[Systools]: Build on Apr 17 2019 at 12:03:37.
[Systools]:SVN NUM: 60434.

Fail to get env coremnt!
Syshelper: WdtSatrtTime = 60(s), appauto = 1, hctosystime = 1500
00:00:03|[prc] Set WdtTimeout To WdtTimeoutMax:47721, instead !
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[systools] appauto 's flag = 1
00:00:03|[systools] please wait sonia to send net info
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[pdc] ERROR (RTC_readTime|362): rtc has trouble!
00:00:03|[pdc] ERROR (RTC_ioctl|525): Fail to read time!
00:00:03|[libpdi] ERROR (PDI_rtcReadTime|240): Fail to ioctl rtc
00:00:03|[systools] ERROR (PDI_syshelperClockToSys|2218): Fail to get rtc time
00:00:03|[SEN-DRV] WARN (SEN_drvCoreCreateSensorDev|1099): Modify hwid SetSensorId 74,0
00:00:03|[SEN-DRV] Sensor 74 Init OK. type:1
00:00:03|[SEN-DRV] pAdjSensors[0],instId=0
00:00:03|[SEN-DRV] SEN_drvCoreInitAdjSensorList over
00:00:03|[SEN-DRV] sensor ID[0] already Alloc
00:00:03|[OSA-DRV] Char device create OK !
00:00:03|[IVF-Drv] IVF Driver(SVN:21909) Build on Apr 18 2019 at 12:35:50.
00:00:03|[IVF-Drv] ERROR (IVF_drvInit|695): Invalid data struct defined(72:368:48:400)!
00:00:03|[OSA-DRV] Char device create OK !
00:00:03|[IVF-Drv] [Linux-KERNEL][IVF_platResInit]dspGrade:0, dspSums:1
00:00:03|[IVF-Drv] IVF Driver install successfull!
00:00:04|[AmbaVideo] AmbaVideo Build on Apr 23 2019 at 02:00:16.
00:00:04|[AmbaVideo] SVN NUM: 22033.

00:00:04|[AmbaVideo] config chan num:1
Vout notice: vout0:0 probed!
Vout notice: vout1:1 probed!
00:00:04|[AmbaVideo] ambpriv_dsp_device = 86ffa8c0
Amber VIN: vin0: probed!
Amber VIN: vin1(virtual): probed!
00:00:04|[AmbaVideo] sensor:74
Amber VIN: IMX290 init(4-lane lvds)
Vout notice: CVBS:0@1 probed!
Vout notice: DBus-All:1@0 probed!
amba_debug_init 248:248.
[: 1: unknown operand
cap_fast =
00:00:04|[sdcard] SD/SDIO/MMC Driver (sdcard.ko) SVN_NUM : 22606
00:00:04|[sdcard] Version: 2.0.00, Build Date: May 17 2019, Time: 03:34:33
00:00:04|[sdcard] SD Memory Card Power En Gpio = 109, Detect Gpio = 65535, hostId = 0
00:00:04|[sdcard] Not Support Wifi Card !
00:00:05|[sdcard] host0 MMC_CAP_NEEDS_POLL
00:00:05|[sdcard] SD Clock: base[48MHz], min[195312Hz], max[50000000Hz].
ambarella-sd e0002000.sdmmc0: 1 slots @ 50000000Hz
00:00:05|[sdcard] SD Clock: base[48MHz], min[195312Hz],net eth0: lp: sym: 0, asym: 0
max[50000000Hz].
libphy: e000e000.etherne:00 - Link is Up - 100/Full
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ambarella-sd e001f000.sdmmc2: 1 slots @ 50000000Hz
map_size = 0x500000, nr_item = 3
addr_offset = 0x00000000, filename = orccode.bin
addr_offset = 0x00300000, filename = orcme.bin
addr_offset = 0x003a0000, filename = default_binary.bin
mmap returns 0x76960000
loading /usr/lib/firmware/orccode.bin...addr = 0x76960000, size = 0x1ad538
loading /usr/lib/firmware/orcme.bin...addr = 0x76c60000, size = 0x3392c
loading /usr/lib/firmware/default_binary.bin...addr = 0x76d00000, size = 0x619c0
===============================================
ucode (S3L) version = 2022/1/12 281966.281888
===============================================
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
hwid_value =IPC-HDBW4231F-AS:01:02:05:4A:21:00:01:0E:01:00:04:2D0:00:00:00:00:00:01:00:00:100
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
product_name =IPC-HDBW4231F-AS
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
lens_type =0
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
fvideo_chip = 74
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
00:00:06|[libpdi] hMcu is null [OSA-APP] OSA Build on Apr 16 2019 at 00:50:18. [OSA-APP] SVN NUM: 21632. [libpdi] libpdi.so Build on Nov 9 2019 [libpdi] partionNum=16 [libpdi] Get fpga upgrade cfg failed, use default [libpdi] Get bootsupportswitchpart failed. [libpdi] Support backup partition !!! [libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000 [libpdi] gFlashCtrlObj.isSupportSwitchPart:0 [libpdi] gFlashCtrlObj.bootFromBack:0 [libpdi] gFlashCtrlObj.bootVersion:2 [libpdi] WARN : Device has no crypt chip! [libpdi] ERROR (PDI_recordInit|282): Record device is not exists [libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL [libpdi] phyaddr= 0x75fe000, memLen= 0x2 [libpdi] PDI_notifyInit Wrapper OK!!! [Systools]: Build on Apr 17 2019 at 12:03:37. [Systools]:SVN NUM: 60434. hwidValue == 0
vout_support =0
cap_vout =
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
dspChip = 33
S3LM= 1
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
sysbackup_value =1
close cvbs and vout

/usr/etc/IPCimod: line 126: /usr/bin/data/amba_debug: not found
[OSA-APP] OSA Build on Apr 16 2019 at 00:50:18.
[OSA-APP] SVN NUM: 21632.

[libpdi] libpdi.so Build on Nov 9 2019 at 09:12:10.
[libpdi] SVN NUM: 68279.
[libpdi] PDI product has 1 configs!!!
/usr/etc/IPCimod: [libpdi] Sensor has 1 sensor(s)
[libpdi] PDI product Init OK!
[libpdi] PDI hwid Get OK!
[libpdi] PDI run in backupd
[libpdi] partionNum=16
[libpdi] Get fpga upgrade cfg failed, use default
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:06|[pdc] The cmd 3221510149 is invalid
[libpdi] Get bootsupportswitchpart failed.
[libpdi] Support backup partition !!!
[libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000
[libpdi] gFlashCtrlObj.isSupportSwitchPart:0
[libpdi] gFlashCtrlObj.bootFromBack:0
[libpdi] gFlashCtrlObj.bootVersion:2
[libpdi] WARN : Device has no crypt chip!
[libpdi] ERROR (PDI_recordInit|282): Record device is not exists
[libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:06|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
[libpdi] phyaddr= 0x75fe000, memLen= 0x2000
00:00:06|[pdc] Both of Chief and Backup File CRC check OK!
[libpdi] Can't open /dev/pdcMcu
[libpdi] PDI_mcuCreate fail
line 126: /usr/bin/data/amba_debug: not found
start sshd
[libpdi] can't find commLen cfg
[libpdi] PDI run in backupd
[libpdi] PDI_eventInit Wrapper OK!!!
[libpdi] run with no coprocessor!
[libpdi] PDI run in backupd
[libpdi] PDI_notifyInit Wrapper OK!!!

[Systools]: Build on Apr 17 2019 at 12:03:37.
[Systools]:SVN NUM: 60434.

00:00:06|[systools] Boot support backup version 2
00:00:06|[libpdi] Read: blkIndex: 0,pageIndex: 0,byteIndex: 0 ,fLag: ffffffff
00:00:06|[libpdi] Read: blkIndex: 0,pageIndex: 1,byteIndex: 0 ,fLag: ffffffff
00:00:06|[libpdi] Read: blkIndex: 0,pageIndex: 2,byteIndex: 0 ,fLag: ffffffff
00:00:06|[libpdi] Read: blkIndex: 0,pageIndex: 3,byteIndex: 0 ,fLag: ffffffff
00:00:06|[systools] Do not need backup!!!
00:00:06|[libpdi] hMcu is null
00:00:06|[pdc] FlashTotalSize = 0x2000000
00:00:07|[pdc] The cmd 3221510149 is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] Both of Chief and Backup File CRC check OK!
audioin = 1
00:00:07|[pdc] FlashTotalSize = 0x2000000
00:00:07|[pdc] The cmd 3221510149 is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] Both of Chief and Backup File CRC check OK!
sensor_id 74
00:00:07|[pdc] FlashTotalSize = 0x2000000
00:00:07|[pdc] The cmd 3221510149 is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:07|[pdc] Both of Chief and Backup File CRC check OK!
wifi = 0
------cap_wifi = 0
unzip: can't open /mnt/pd/product.zip, /mnt/pd/product.zip.zip, /mnt/pd/product.zip.ZIP
/usr/local/etc/sshd_config line 20: Deprecated option KeyRegenerationInterval
/usr/local/etc/sshd_config line 21: Deprecated option ServerKeyBits
/usr/local/etc/sshd_config line 33: Deprecated option RSAAuthentication
/usr/local/etc/sshd_config line 40: Deprecated option RhostsRSAAuthentication
cp: can't stat '/usr/data/osd.bmp': No such file or directory
cp: can't stat '/var/tmp/product/ProductTransform': No such file or directory
cp: can't stat '/var/tmp/product/CustomTemplate': No such file or directory
cp: can't stat '/var/tmp/product/CustomPathSensitive': No such file or directory
cp: can't stat '/var/tmp/product/ProductPathSensitive': No such file or directory
cp: can't stat '/var/tmp/product/DefaultAccount': No such file or directory
cp: can't stat '/var/tmp/product/MaskConfig.json': No such file or directory
product=IPC-HF4231E
cp: can't stat '/var/tmp/product/IPC-HF4231E/*': No such file or directory
sed: /var/tmp/pd/ProductDefinition: No such file or directory
ln: /mnt/mtd/3A/aew_para.zip: No space left on device
unzip: can't open /mnt/mtd/3A/aew_para.zip, /mnt/mtd/3A/aew_para.zip.zip, /mnt/mtd/3A/aew_para.zip.ZIP
Default manual len in manual
manual
IPC-HDBW4231F-AS
cp: can't stat '/mnt/web/osd.bmp': No such file or directory
cp: can't stat '/var/tmp/osd.bmp': No such file or directory
cap_dsp = DSP
appauto=1

[OSA-APP] OSA Build on Apr 16 2019 at 00:50:18.
[OSA-APP] SVN NUM: 21632.

[libpdi] libpdi.so Build on Nov 9 2019 at 09:12:10.
[libpdi] SVN NUM: 68279.
[libpdi] PDI product has 1 configs!!!
[libpdi] Sensor has 1 sensor(s)
[libpdi] PDI product Init OK!
[libpdi] PDI hwid Get OK!
[libpdi] PDI run in sonia
[libpdi] >>logChn[0]

hyChip[0]:33, phyChn[0]:2
[libpdi] Vin has 1 Cfg(s)
[libpdi] Vout has 1 Cfg(s)
[libpdi] partionNum=16
[libpdi] Get fpga upgrade cfg failed, use default
00:00:12|[pdc] FlashTotalSize = 0x2000000
00:00:12|[pdc] The cmd 3221510149 is invalid
[libpdi] Get bootsupportswitchpart failed.
[libpdi] Support backup partition !!!
[libpdi] Flashtype = 0x3,patSize = 0x40000,rwSize = 0x10000,ersSize = 0x10000
[libpdi] gFlashCtrlObj.isSupportSwitchPart:0
[libpdi] gFlashCtrlObj.bootFromBack:0
[libpdi] gFlashCtrlObj.bootVersion:2
[libpdi] WARN : Device has no crypt chip!
[libpdi] ERROR (PDI_recordInit|282): Record device is not exists
[libpdi] ERROR (PDI_preInit|198): PDI_recordInit execute Error and return OSA_EFAIL
00:00:12|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
00:00:12|[pdc] WARN (MISC_ioctl|2021): The cmd is invalid
[libpdi] phyaddr= 0x75fe000, memLen= 0x2000
00:00:12|[pdc] Both of Chief and Backup File CRC check OK!
[libpdi] Can't open /dev/pdcMcu
[libpdi] PDI_mcuCreate fail
[libpdi] can't find commLen cfg
[libpdi] PDI_eventInit OK!!!
[libpdi] run with no coprocessor!
[OSA-APP] pdi_notify_thr Task pid=333 tid=335
[libpdi] PDI_notifyInit suce!
[00:00:14 info Infra 333 Unknown:0][*] 0.0.0.0 Built in 0/ 0/ 0 [*]
Reflector::register: type=CDefaultOsdBuilder
[00:00:15 info Infra 333 Unknown:0]Some [Manager] files are not commit to SVN server. It compied wtih local modified files.
[00:00:16 info Infra 333 Unknown:0]Some [Infra2] files are not commit to SVN server. It compied wtih local modified files.
[libvsf] libvsf.a svn num: 22559 Last Build:Jun 27 2019 03:44:43
00:00:17|[Binder-Lib] libbinder.so Build on Apr 17 2019 at 11:57:00.
00:00:17|[Binder-Lib] SVN NUM: 4577.

00:00:17|[libvsf] ****VSF FRAMEWORK
00:00:17|[libvsf]

00:00:17|[libvsf] /usr/bin/sonia Build on Jun 27 2019 at 03:44:43.
00:00:17|[libvsf] SVN NUM: 22559.

00:00:17|[libvsf] VSF_cfgGetFisheyeCaps: product line 2, model 319; Fish eye type 0, lens mounts 0, corrections 0, DPTZ commands 0.
00:00:17|[libvsf] Initialized server config. Product line 2, model 319. Supporting mask 0x8103019
00:00:17|[libvsf] VSF_shmInit succeed
00:00:17|[libvsf] Node VSF_Node_0x05010000 created
00:00:17|[libvsf] VSF_ctrlInit succeed
00:00:17|[AEW] AEWB ALG Build on May 8 2019 at 00:36:14.
00:00:17|[AEW] SVN NUM: 61247.

00:00:17|[AEW] AMBA LIB: Version:2.5.15 modTime:0x20171212
00:00:17|[AEW] the aew cfg ver: 1.032
00:00:17|[AEW] the aew cfg date time is: 2019-04-22 12:35:14
00:00:17|[AEW] the aew cfg subVer is: 60617.000
00:00:17|[AEW] the aew cfg chipName is:

00:00:17|[AEW] the aew cfg pdtName is: IPC-HF5231E
00:00:17|[AEW] OK, use cfg:/var/tmp/aew_para.bin
cp: can't create '/mnt/mtd/3A/aew_para.zip': No space left on device
00:00:17|[AEW] between 2A and sonia msg creat OK
00:00:17|[H3A] H3A Build on Apr 17 2019 at 01:12:40.
00:00:17|[H3A] SVN NUM: 53046.

Fail to get env icrtype!
00:00:17|[libpdi] [ICR]isReverse = 0
00:00:17|[libpdi] [ICR]aewType = 0
00:00:17|[libpdi] [ICR]nDevNum = 1
00:00:17|[pdc] needReverse = 0
00:00:17|[pdc] ....turn into DAY mode....
00:00:17|[libpdi] aDex = 1.000000
00:00:17|[libpdi] bDex = 0.000000
00:00:17|[ICR] ICR Build on Apr 18 2019 at 06:57:31.
00:00:17|[ICR] SVN NUM: 60453.

00:00:17|[ICR] icr is created successful!
00:00:17|[ICR] adc is created successful!
00:00:17|[ICR] adc type: 4.
00:00:17|[ICR] adc state get successful!
00:00:17|[ICR] adcState=b5db5d00, c2bAdcThr=a000000, realDncMode=1
00:00:17|[ICR] the icr cfg ver: 1.006
00:00:17|[ICR] the icr cfg date time is: 2019-04-18 14:57:32
00:00:17|[ICR] the icr cfg subVer is: 60453.000
00:00:17|[ICR] the icr cfg chipName is: s3l
00:00:17|[ICR] the icr cfg pdtName is: imx290
00:00:17|[ICR] OK, use icr cfg:/var/tmp/3A/icr_para.bin
00:00:17|[AE] SmartIR Build on Apr 17 2019 at 12:27:05.
00:00:17|[AE] SVN NUM: 60438.

00:00:17|[OSA-APP] ERROR (OSA_fileOpen|216): Open /var/tmp/ir_lens_para.bin failed
00:00:17|[AE] ERROR (APP_commCfgReadCheckParam|89): Open /var/tmp/ir_lens_para.bin file failed
00:00:17|[AE] APP_commCfgReadCheckParam /var/tmp/ir_lens_para.bin failed!
00:00:17|[AE] APP_commCfgLoad /var/tmp/ir_lens_para.bin failed!
00:00:17|[OSA-APP] ERROR (OSA_fileOpen|216): Open /var/tmp/0/ir_lens_para.bin failed
00:00:17|[AE] ERROR (APP_commCfgReadCheckParam|89): Open /var/tmp/0/ir_lens_para.bin file failed
00:00:17|[AE] APP_commCfgReadCheckParam /var/tmp/0/ir_lens_para.bin failed!
00:00:17|[AE] Use default zoomPrioFarLightOnPosThr = 365
00:00:17|[libpdi] ERROR (PDI_irisInit|274): Can't open /dev/pdcIris
00:00:17|[libpdi] ERROR (PDI_irisCreate|709): PDI_irisInit err!
create iris handle failed
00:00:17|[libpdi] ERROR (PDI_irisInit|274): Can't open /dev/pdcIris
00:00:17|[libpdi] ERROR (PDI_irisCreate|709): PDI_irisInit err!
00:00:17|[AEW] ERROR (Drv_aewIrisAdaptorCreate|44): PDI_irisCreate Failed!
00:00:17|[AEW] ERROR (DRV_aeCreate|61): create iris handle failed,file: ../src/algae_adaptor/s3l/drv_aew_ae_adaptor.c func: DRV_aeCreate
00:00:17|[AE] Eyebot AE Build on Apr 17 2019 at 12:27:05.
00:00:17|[AE] SVN NUM: 60438.

00:00:17|[AE] the cfg ver: 1.007
00:00:17|[AE] the cfg date time is: 2019-04-17 20:27:07
00:00:17|[AE] the cfg subVer is: 60438.000
00:00:17|[AE] the cfg chipName is: s3l
00:00:17|[AE] the cfg pdtName is: imx290
00:00:17|[AE] OK, use cfg:/var/tmp/3A/ae_eyeBot_para.bin
00:00:17|[OSA-APP] ERROR (OSA_fileOpen|216): Open /var/tmp/ae_eyeBot_lens_para.bin failed
00:00:17|[AE] ERROR (APP_commCfgReadCheckParam|89): Open /var/tmp/ae_eyeBot_lens_para.bin file failed
00:00:17|[AE] APP_commCfgReadCheckParam /var/tmp/ae_eyeBot_lens_para.bin failed!
00:00:17|[AE] APP_commCfgLoad /var/tmp/ae_eyeBot_lens_para.bin failed!
00:00:17|[OSA-APP] ERROR (OSA_fileOpen|216): Open /var/tmp/0/ae_eyeBot_lens_para.bin failed
00:00:17|[AE] ERROR (APP_commCfgReadCheckParam|89): Open /var/tmp/0/ae_eyeBot_lens_para.bin file failed
00:00:17|[AE] APP_commCfgReadCheckParam /var/tmp/0/ae_eyeBot_lens_para.bin failed!
00:00:17|[pdc] Get motor cfg failed !
00:00:17|[libpdi] pLensType = 0
00:00:17|[AEW] lensType = 0, it's not Hall Lens
00:00:17|[AE] PID DC IRIS Build on Apr 17 2019 at 12:27:06.
00:00:17|[AE] SVN NUM: 60438.

00:00:17|[AEW] aewb creat over
00:00:17|[libvsf] Node VSF_Node_0x01010000 created
00:00:17|[libvsf] VSF_aewInit
Connection established with kernel.
00:00:17|[libvsf] Node VSF_Node_0x09010000 created
00:00:17|[libvsf] LANG is not SimpChinese
00:00:17|[libvsf] VSF_drvSysInit
00:00:17|[libvsf] VSF_drvVinInit
00:00:17|[libvsf] VSF_drvVoutInit
00:00:17|[libvsf] VSF_drvEncInit
00:00:17|[libvsf] VSF_drvStrmInit
00:00:17|[libvsf] VSF_drvPmInit
00:00:17|[libvsf] VSF_drvOsdInit
00:00:17|[libvsf] VSF_drvYuvInit
00:00:17|[libvsf] VSF_drvRoiInit
00:00:17|[libvsf] i = 1 width 720 height 576
00:00:17|[libvsf] nPrdtLineId = 2, nSensorId = 74, nHwVersionId = 0
00:00:17|[libvsf] numStream: 3
00:00:17|[libvsf] VIN channel0 create done
00:00:17|[libvsf] start to enter idle
00:00:17|[libvsf] VSF_drvEncGotoIdle done
00:00:17|[libvsf]
Find Vin Source imx290 00:00:17|[libvsf] it supports:
00:00:17|[libvsf] 1920x1080P 60 RGB 12bits 16:9 AUTO rev[0]
00:00:17|[libvsf] 1920x1080P 60 RGB 12bits 16:9 AUTO rev[0]
00:00:17|[libvsf] Active src 0's mode is:
00:00:17|[libvsf] 1920x1080P 25 RGB 12bits 16:9 AUTO rev[0]
00:00:17|[libvsf] init_vin done
00:00:17|[libvsf] Buffer Resource Limit mode=0 [1920 1080] [704 576] [1280 720] [320 240]
00:00:17|[libvsf] stream Resource Limit [1920 1080] [704 576] [1280 720] [1920 1080]
00:00:17|[libvsf] mode = 0, rotate_enable = 0, iso_type = 2, debug_enable = 0, rawEn = 0
00:00:17|[libvsf] encode Set fmt type 1 width 1920 height 1080 source 0 id 0
00:00:17|[libvsf] encode Set fmt type 1 width 704 height 576 source 1 id 1
00:00:17|[libvsf] encode Set fmt type 1 width 1280 height 720 source 2 id 2
00:00:17|[libvsf] encode Set fmt type 2 width 1920 height 1080 source 0 id 3
00:00:17|[AEW] ../src/s3l/alg_mutualS3l.c::ALG_Mutual_Get_3A_LoopMode:493 LoopMode=1
00:00:17|[AEW] get amba sensor id=12307
00:00:17|[AEW] get amba vin_mode=131091, vin_fps=20480000
00:00:17|[AEW] get the product info: sensor id is 74, product type is 319.
00:00:17|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:17|[libpdi] pIcrAewType = 0
00:00:17|[AEW] File[../src/s3l/mw_sensor_param.c] Line[179], icrAewType=0
00:00:17|[AEW] Global_GetMwSensorParam()->sensor_id is 74
wb_param is cfg_wb_param!
00:00:17|[AEW] lensType = 0
00:00:17|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[AEW] ====Global_GetWmSysRes()->isp_pipeline=2====

>> pipline:2, hdr_mode:0, method:0, expo_num:1, raw_pitch:0
>> main:size 1920x1088, raw:1920x1088, resolution:12

00:00:18|[AEW] get amba sensor id=12307
00:00:18|[AEW] get amba vin_mode=131091, vin_fps=20480000
00:00:18|[AEW] get the product info: sensor id is 74, product type is 319.
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[libpdi] pIcrAewType = 0
00:00:18|[AEW] File[../src/s3l/mw_sensor_param.c] Line[179], icrAewType=0
00:00:18|[AEW] Global_GetMwSensorParam()->sensor_id is 74
wb_param is cfg_wb_param!
00:00:18|[AEW] lensType = 0
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[AEW] ====Global_GetWmSysRes()->isp_pipeline=2====

>> load_cc_bin_customer_loop:590 load cc binary done.
>> enable_cc_customer_loop:543 enable cc binary done.

DSP DRAM Used: 28 MB, Limited: 103 MB.
DSP DRAM Used: 73 MB, Limited: 103 MB.
00:00:18|[AEW] ../src/s3l/alg_mutualS3l.c::ALG_Mutual_Get_3A_LoopMode:493 LoopMode=1

>> AAA start done!

00:00:18|[libvsf] WARN (VSF_drvEncEnablePreview|1186): set lite store parame is fail
00:00:18|[libvsf] enable preview done
00:00:18|[OSA-APP] smartH26x_Tsk Task pid=333 tid=344
00:00:18|[libvsf] streamId:0, old:0x0, fps:0, new:1920x1080,25
00:00:18|[libvsf] vin:25,1920,1080, sensor:25,1920,1080
00:00:18|[libvsf] start to enter idle
00:00:18|[AEW] ../src/s3l/alg_mutualS3l.c::ALG_Mutual_Get_3A_LoopMode:493 LoopMode=1

>> AAA stop done!

00:00:18|[libvsf] VSF_drvEncGotoIdle done
00:00:18|[libvsf] encode Set fmt type 1 width 1920 height 1080 source 0 id 0
00:00:18|[libvsf] encode Set snap fmt type 2 width 1920 height 1080 source 0 id 3
00:00:18|[AEW] ../src/s3l/alg_mutualS3l.c::ALG_Mutual_Get_3A_LoopMode:493 LoopMode=1
00:00:18|[AEW] get amba sensor id=12307
00:00:18|[AEW] get amba vin_mode=131091, vin_fps=20480000
00:00:18|[AEW] get the product info: sensor id is 74, product type is 319.
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[libpdi] pIcrAewType = 0
00:00:18|[AEW] File[../src/s3l/mw_sensor_param.c] Line[179], icrAewType=0
00:00:18|[AEW] Global_GetMwSensorParam()->sensor_id is 74
wb_param is cfg_wb_param!
00:00:18|[AEW] lensType = 0
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[AEW] ====Global_GetWmSysRes()->isp_pipeline=2====

>> pipline:2, hdr_mode:0, method:0, expo_num:1, raw_pitch:0
>> main:size 1920x1088, raw:1920x1088, resolution:12

00:00:18|[AEW] get amba sensor id=12307
00:00:18|[AEW] get amba vin_mode=131091, vin_fps=20480000
00:00:18|[AEW] get the product info: sensor id is 74, product type is 319.
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[libpdi] pIcrAewType = 0
00:00:18|[AEW] File[../src/s3l/mw_sensor_param.c] Line[179], icrAewType=0
00:00:18|[AEW] Global_GetMwSensorParam()->sensor_id is 74
wb_param is cfg_wb_param!
00:00:18|[AEW] lensType = 0
00:00:18|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:18|[AEW] ====Global_GetWmSysRes()->isp_pipeline=2====

>> load_cc_bin_customer_loop:590 load cc binary done.
>> enable_cc_customer_loop:543 enable cc binary done.

DSP DRAM Used: 28 MB, Limited: 103 MB.
DSP DRAM Used: 73 MB, Limited: 103 MB.
00:00:18|[AEW] ../src/s3l/alg_mutualS3l.c::ALG_Mutual_Get_3A_LoopMode:493 LoopMode=1

>> AAA start done!

00:00:18|[libvsf] WARN (VSF_drvEncEnablePreview|1186): set lite store parame is fail
00:00:18|[libvsf] enable preview done
00:00:18|[libvsf] source buffer config: buffer 1, size 704x576, input 1920,1080 (0,0)
00:00:18|[libvsf] encode Set fmt type 1 width 704 height 576 source 1 id 1
00:00:18|[libvsf] source buffer config: buffer 2, size 1280x720, input 1920,1080 (0,0)
00:00:18|[libvsf] encode Set fmt type 1 width 1280 height 720 source 2 id 2
00:00:18|[libvsf] encode Set fmt type 2 width 1920 height 1080 source 0 id 3
00:00:18|[libvsf] VSF_algEncInit
00:00:18|[libvsf] overlay: offset = 0x7c00000, virt:0x70c24000, size = 0x200000
00:00:18|[libvsf] OSD mem addr 0x70c28000, size 2080768; max OSD count 5; mem free ticks 15; osdMemReduce 0.dspSum 1,isMulChipOsd 0
00:00:18|[OSA-APP] malgFree Task pid=333 tid=345
00:00:18|[libvsf] Initializing OSD module done.
00:00:18|[libvsf] stream_matrix_num = 2, single_matrix_size = 0x20000!
00:00:18|[OSA-APP] roiTsk Task pid=333 tid=346
00:00:18|[libvsf] VSF_algRoiInit
00:00:18|[libvsf] VSF_algPmInit
00:00:18|[libvsf] VSF_algDptzInit
00:00:18|[libvsf] Packet phyaddr:0x7600000, virtaddr:0x6ebe5000, size:0x600000
00:00:18|[libvsf] WARN : not support appStrmId Id 3
00:00:18|[libvsf] VSF_algPktInit
00:00:18|[OSA-APP] heartB_Tsk Task pid=333 tid=349
00:00:18|[libvsf] VSF_encInit
00:00:18|[OSA-APP] debug Task pid=333 tid=351
00:00:18|[libvsf] VSF_dbgInit
00:00:18|[libvsf] isSupportVad 1
00:00:18|[libvsf] yuvParam.intelliPoolNum 0
00:00:18|[libvsf] Node VSF_Node_0x06010000 created
00:00:18|[libvsf] VSF_dtcInit
00:00:18|[libivf] IVF library(SVN:21909) Build on Apr 18 2019 at 20:35:48.
00:00:18|[IVF-Drv] Process ['sonia':333] open IVF driver!
00:00:18|[libivf] [Linux-USER][IVF_platResInit]dspGrade:0, dspSums:1
00:00:18|[pdc] Get motor cfg failed !
00:00:18|[libpdi] pLensType = 0
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libivf] IVF_entryProces(0) Task pid=333 tid=353
00:00:18|[libivf] IVF_entryProces(1) Task pid=333 tid=355
00:00:18|[libivf] IVF_entryProces(3) Task pid=333 tid=356
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libvsf] VSF_algIntelliTask Task pid=333 tid=360
00:00:18|[libvsf] VSF_algIntelliInit
00:00:18|[libvsf] VSF_intelliInit ~~~~~~~~~~~~~ 1788
00:00:18|[libpdi] createVideoInput: channel(id) 0, channels: 1
00:00:18|[libpdi] createVideoInput_IPC pVideoInput->priv=0x31f5cc8, priv = 0x31f5cc8
00:00:18|[libpdi] id:0 getConfig fun[1]: 0x18538b bnd: 0x0, bndLen:0x0
00:00:18|[libpdi] id:0 getConfig fun[1]: 0x1070a00 bnd: 0x0
00:00:18|[libpdi] getConfig fun[2]: 0x0
00:00:18|[libpdi] getConfig fun[3]: 0x0
00:00:18|[libpdi] bndFlag: 0x3
00:00:18|[DH_Binder] WARN : Two port 0x14d2aa8 - 0x14d2aa4 on the same process !
00:00:18|[DH_Binder] WARN : Two port 0x14d2aa9 - 0x14d2aa2 on the same process !
00:00:18|[libvsf] VSF_intelliInit
00:00:18|[libvsf] VSF_init fastEnable[0]
00:00:18|[AEW] begin start aewb, SVN NUM=61247, build in May 8 2019 00:36:14......

>> ======= [DONE] mw_start_aaa =======

00:00:18|[AEW] amba mw aaa is started ok.
00:00:18|[AEW] start amba mw is OK
00:00:18|[AEW] adj_set_freeze_enable 0
00:00:18|[AEW] ALG_aewStart:standard=0
00:00:18|[AEW] encWidth = 1920,encHeight = 1080,realWidth = 1920,realHeight = 1080,n_x=0,n_y=0,n_r=0
00:00:18|[AEW] aeTagRatio=100, productType=319
00:00:18|[pdc] Get motor cfg failed !
00:00:18|[libpdi] pLensType = 0
00:00:18|[libpdi] ERROR (PDI_irisInit|274): Can't open /dev/pdcIris
00:00:18|[libpdi] ERROR (PDI_irisCreate|709): PDI_irisInit err!
create iris handle failed
00:00:18|[libdsp] ITS_intelliCapRun(3) Task pid=333 tid=359
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libdsp] ITS_intelliCapRun(1) Task pid=333 tid=358
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libdsp] ITS_intelliCapRun(0) Task pid=333 tid=357
00:00:18|[libiva] [ANLS_cfgGetChannelInfo] prodName IPC-HDBW4231F-AS
00:00:18|[libivf] IVF_nodeTskRun Task pid=333 tid=354
open_pwm_proc error
: No such file or directory
!!! [src/mw_image.c: 1050]dc_iris_enable error

00:00:18|[libvsf] isLongExp:0, expFps=25
00:00:18|[libvsf] VSF_COM_SET_LONG_EXP
00:00:18|[libvsf] VSF_drvEncAdjustByLongExp isLongExp:0, expFps:25
00:00:18|[AEW] ERROR (Drv_aewIrisAdaptorAdjustSize|131): hIris is NULL!
00:00:18|[AEW] ALG_awbReset

a_wb_gain->r=1.500000,pa_wb_gain->b=1.500000
ALG_awbReset:currWbGain.r_gain=1536,currWbGain.b_gain=1536
00:00:18|[libpdi] smartIr Type:1
00:00:18|[AE] ledCount:1,ledNUM:0
00:00:18|[AE] irPipeId:0 ,IR-is~ok~!!!!!!!!!!!-Enable OK,i_count=0,i_ircount=1
00:00:18|[AE] irPipeId:0 ,aewWLCheck-ledCount=1,ledType=1,
00:00:18|[AE] Set SD/IPC LIGHT_TYPE[1] DutyRation: 0, Frequence:50000
00:00:18|[AE] SMARTIR:the state is inited to closed!
00:00:18|[pdc] Get motor cfg failed !
00:00:18|[libpdi] pLensType = 0
00:00:18|[AEW] File[../src/alg_isp.c],Line[237] lensType=0
00:00:18|[AEW] File[../src/alg_isp.c],Line[245] funcValue=0
00:00:18|[AEW] File[../src/alg_isp.c],Line[246] funcLscFlag=0 ,funcGrGbFlag=0
00:00:18|[AEW] pa_lensTypePara->grgbmismatchCorrEn = 0
00:00:18|[AEW] restart aew time normal =120 ms
00:00:18|[libvsf] VSF_dtcStart
00:00:18|[libvsf] VSF_start
Start videoDaemon ok
00:00:18|[libvsf] Detection execute cmd:0x8
00:00:18|[AEW] start AEW is OK ......
00:00:18|[libpdi] getPtzType
00:00:18|[AEW] currWdrType=0,currAeFlag=8
00:00:18|[libvsf] wdrType:0
00:00:18|[AEW] OpSetWdr set wdr type to : 0
00:00:18|[AEW] ALG_CustomerLoopThread Task pid=333 tid=361
00:00:18|[AEW] ALG_AutoIRThread Task pid=333 tid=362
00:00:18|[libvsf] VSF_COM_SET_WDR_TYPE
00:00:19|[AEW] ERROR (Drv_aewIrisAdaptorAdjustSize|131): hIris is NULL!
00:00:19|[AE] ALG_AutoExposeThread Task pid=333 tid=364
00:00:19|[AEW] ERROR (Drv_aewIrisAdaptorAdjustSize|131): hIris is NULL!
00:00:19|[AEW] ERROR (Drv_aewIrisAdaptorAdjustSize|131): hIris is NULL!
00:00:19|[AE] ALG_aewLightCtrMutexMap-lightsCtrlNoMutex=0,ctrlMode=3
00:00:19|[AE] ALG_aewSmartWLIrModeMap-IrWLMode[0]=3,Mode[1]=3,lamp0=0,lamp1=0
00:00:19|[AE] manual-ratio-IR-near=0,middle=0,far=0,WL=[0-0-0],correction0~1=[0-0]
00:00:19|[AEW_DRV] OpStopDtc Called.
00:00:19|[ICR] b2c FilterDelay smartIrFlag:0,b2cIrwaitingTime:0,maxb2cIrwaitingTime:1500
00:00:19|[pdc] ....turn into DAY mode....
00:00:19|[libvsf] Detection execute cmd:0x8
00:00:19|[AEW_DRV] setDayNightColor Called. dncMode:1
00:00:19|[ICR] ICR:the state is inited to color icr!
00:00:19|[ICR] ERROR (ALG_icrAppSet|1126): The c2bSensitivityLevel =0 does not suppourted, use Mid Sensitivity!
00:00:19|[ICR] WARN (ALG_icrAppSet|1204): ByGain: the param of day night cut is unsuitable
00:00:19|[AEW] set awb mode is OK...
00:00:19|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:0.000,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:19|[AEW] Global_GetHdrPipeLine=0, lastHdrPipeLine=255
00:00:19|[AEW] change tone
00:00:19|[AEW] ../src/s3l/mw_sensor_param.c::chooseCurParam:80 curParamType=0
00:00:19|[AEW] Set cfa▒▒sc...adj params to 1 OK!
00:00:19|[AEW] set adj prarms is OK...
00:00:19|[AEW] set static bpc calibration OK...
00:00:19|[AEW] set night color mode is OK...
00:00:19|[AEW] saturation=40,pa_algColor->saturation=50
00:00:19|[AEW] curr sat level =40
00:00:19|[AEW] get curvParam is error...
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] shparEnb: 1,sharp_ratio: 1.200000,sharp_level: 50
00:00:19|[AEW] set sharpness & 2dnr is OK...
00:00:19|[AEW] mwMctfLevel =6, ktnfLevel =50
00:00:19|[AEW] ktnf enable=1
00:00:19|[AEW] set ktnf is OK...
00:00:19|[AEW] set vd rotate is OK...
00:00:19|[AEW] set vstd is OK...
00:00:19|[AEW] set 3D.bin is OK && currGammaTable = 0
00:00:19|[AEW] currWdrType=0,currAeFlag=8
00:00:19|[libvsf] wdrType:0
00:00:19|[AEW] OpSetWdr set wdr type to : 0
00:00:19|[ICR] ERROR (ALG_icrAppSet|1126): The c2bSensitivityLevel =0 does not suppourted, use Mid Sensitivity!
00:00:19|[ICR] WARN (ALG_icrAppSet|1204): ByGain: the param of day night cut is unsuitable
00:00:19|[libvsf] VSF_COM_FLIP_ROTATE
00:00:19|[libvsf] same view
00:00:19|[libvsf] set pView 0 0 0
00:00:19|[libvsf] set Dtc pView 0 0 0
00:00:19|[libvsf] VSF_COM_SET_WDR_TYPE
00:00:19|[AEW] set awb mode is OK...
00:00:19|[AEW] saturation=40,pa_algColor->saturation=50
00:00:19|[AEW] curr sat level =40
00:00:19|[AEW] get curvParam is error...
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] shparEnb: 1,sharp_ratio: 1.200000,sharp_level: 50
00:00:19|[AEW] set sharpness & 2dnr is OK...
00:00:19|[AEW] set awb mode is OK...
00:00:19|[AEW] saturation=40,pa_algColor->saturation=50
00:00:19|[AEW] curr sat level =40
00:00:19|[AEW] brt = 50, sat = 40, hue = 50, crt = 50
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] set awb mode is OK...
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] set awb mode is OK...
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:7.898,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] curr gam level =50
00:00:19|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:11.297,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:13.836,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] set night color mode is OK...
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:15.685,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:20|[AEW] curr gam level =50
00:00:21|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:17.178,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:21|[AEW] pa_algColor->contrast = 50, pa_autoClrPara->crtLevel = [50, 50],
pa_algColor->saturation = 50, pa_autoClrPara->satLevel = [50, 50],
pa_algColor->brightness = 50, pa_autoClrPara->brtLevel = [50, 50],
pa_algColor->gamLevel = 50, pa_autoClrPara->gamLevel = [50, 50],
, senGain:19.176,pa_autoClrPara->minSenGain:24.000,pa_autoClrPara->maxSenGain:30.000,
00:00:21|[AEW] saturation=40,pa_algColor->saturation=50
00:00:21|[AEW] curr sat level =40
00:00:21|[AEW] set night color mode is OK...
[00:00:22 trace Unknown 333 Unknown:0]main( /usr/bin/sonia AEWB DSP EX2)
[00:00:22 info Unknown 333 Unknown:0]Pack Environment
HDCameraS2L/Trunk @ 1289998:1293607M
[00:00:22 trace Unknown 333 Unknown:0]app lib info
[00:00:22 info Infra 333 Unknown:0][*] Function 1.1.0.1181017 Built in 2022/ 1/25 [*]
[00:00:22 info Infra 333 Unknown:0][*] Manager 1.1.0.1242031 Built in 2022/ 6/ 7 [*]
[00:00:22 info Infra 333 Unknown:0][*] NetApp 3.0.0.863260 Built in 2020/ 3/16 [*]
[00:00:22 info Infra 333 Unknown:0][*] Storage 1.0.1.858284 Built in 2020/ 3/11 [*]
[00:00:22 info Infra 333 Unknown:0][*] Function 1.1.0.1181017 Built in 2022/ 1/25 [*]
[00:00:22 trace Unknown 333 Unknown:0]app lib info
[00:00:22 info StreamApp:848461 333 StreamApp.cpp:20][StreamAppComponent] initStreamAppServerComponent
[00:00:22 info StreamSvr:843511 333 Framestate.cpp:10][StreamSvrComponent] initStreamSvrFrameStateComponent
[00:00:22 info StreamApp:848461 333 InitStreamAppComponentLibrary.cpp:44][StreamAppComponent] register all Component
[00:00:22 info StreamApp:848461 333 StreamApp.cpp:20][StreamAppComponent] initStreamAppServerComponent
[00:00:22 info StreamSvr:843511 333 Framestate.cpp:10][StreamSvrComponent] initStreamSvrFrameStateComponent
[00:00:22 info StreamApp:848461 333 DHEncrypt.cpp:11][StreamAppComponent] initStreamAppPrivateFrameEncryptComponent
[00:00:22 info StreamApp:848461 333 RtspRealStream.cpp:28][StreamAppComponent] initStreamAppRtspStreamSourceComponent
[00:00:22 info StreamApp:848461 333 QuickMulticast.cpp:19][StreamAppComponent] initStreamAppQuickMulticastComponent
[00:00:22 info StreamApp:848461 333 TalkbackClient.cpp:16][StreamAppComponent] initStreamAppHttpTalkClientComponent
[00:00:22 info StreamApp:848461 333 TsMulticastService.cpp:10][StreamAppComponent] initStreamAppTsMulticastServiceComponent
[00:00:22 info StreamApp:848461 333 UdpMulticastService.cpp:7][StreamAppComponent] initStreamAppUdpMulticastServiceComponent
[00:00:22 info StreamApp:848461 333 TalkbackSvr.cpp:23][StreamAppComponent] initStreamAppHttpTalkbackSvrComponent
[00:00:22 info StreamSvr:843511 333 TransformatBase.cpp:9][StreamAppComponent] initStreamSvrParseCreaterComponent
[00:00:22 info StreamApp:848461 333 MikeyAdapter.cpp:21][StreamAppComponent] initStreamAppDHEncryptClientComponent
[00:00:22 info StreamApp:848461 333 SslSvr.cpp:9][StreamAppComponent] initStreamAppSSlSvrComponent
[00:00:22 info StreamApp:848461 333 DataSrcBufferManager.cpp:10][StreamAppComponent] initStreamAppDataSrcBufferComponent
[00:00:22 info StreamApp:848461 333 QuickMulticast.cpp:19][StreamAppComponent] initStreamAppQuickMulticastComponent
[00:00:22 info StreamApp:848461 333 TsMulticastService.cpp:10][StreamAppComponent] initStreamAppTsMulticastServiceComponent
[00:00:22 info StreamApp:848461 333 TalkbackSvr.cpp:23][StreamAppComponent] initStreamAppHttpTalkbackSvrComponent
[00:00:22 info StreamSvr:843511 333 TransformatBase.cpp:9][StreamAppComponent] initStreamSvrParseCreaterComponent
[00:00:22 info StreamApp:848461 333 RtspWebsocketSession.cpp:12][StreamAppComponent] initStreamAppRtspWebSocketComponent
[00:00:22 info StreamApp:848461 333 RtmpPushClientImpl.cpp:12][StreamAppComponent] initStreamAppRtmpPushClientComponent
[00:00:22 info StreamApp:848461 333 DHEncrypt.cpp:11][StreamAppComponent] initStreamAppPrivateFrameEncryptComponent
[00:00:22 info StreamApp:848461 333 DhtsSvr.cpp:11][StreamAppComponent] initStreamAppUdtSvrComponent
[00:00:22 info StreamSvr:843511 333 DhtsSockConvert.cpp:10][StreamSvrComponent] initStreamSvrDhtsSockComponent
ethNum = 1
[00:00:22 trace NetProtocol:1242262 333 arp.cpp:38]initNetProtocolArpComponentLibrary!
[00:00:22 trace NetProtocol:1242262 333 arp.cpp:38]initNetProtocolArpComponentLibrary!
[00:00:22 trace NetProtocol:1242262 333 IPv6ConflictCheckNew.cpp:1045]initNetProtocolIpv6ConflictCheckNewComponentLibrary!
[00:00:22 info InterVideoONVIF:1250972 333 OnvifInterVideo.cpp:217]initOnvifMetaStreamComponentLibrary called!
i called
Storage this = 0x14e7d94
i called
122 I register FileManager Factory in storage clsid=Local ret=1
[00:00:22 trace libStoragePosix 333 UserConfig.cpp:30]insight@CUserConfig setConfig table:{
"EventsMap" : {
"AlarmLocal" : "A",
"Card" : "C",
"Manual" : "F",
"Marked" : "K",
"Timing" : "R"
}
}

[00:00:22 trace Manager 333 Unknown:0]CConsole::registerCmd had been register!!
[00:00:22 trace Infra 333 Unknown:0]CThreadManager::CThreadManager()>>>>>>>>>
00:00:22|[pdc] pCbparams->OpSetBeep = null
00:00:22|[libpdi] pWrapper->beep = NULL
00:00:22|[libpdi] >-------System3_getSystemInfo------->
Fail to get env dvname!
Fail to get env devOEM!
Fail to get env authcode!
00:00:22|[libpdi] Get authcode error
Fail to get env productDate!
Fail to get env peripheral!
00:00:22|[libpdi] Can't open /dev/pdcFinger
00:00:22|[libpdi] deviceChannel[0]: IPC
00:00:22|[libpdi] deviceType: IPC-HDBW4231F-AS
00:00:22|[libpdi] processorType: 33
00:00:22|[libpdi] hardwareVersion: 1.00
00:00:22|[libpdi] appAutoStart: 1
00:00:22|[libpdi] deviceClass: IPC
00:00:22|[libpdi] noPtz: 1
00:00:22|[libpdi] noSdCard: 0
00:00:22|[libpdi] noRTC: 0
00:00:22|[libpdi] bandWidth: 80
00:00:22|[libpdi] channelNum: 1
00:00:22|[libpdi] fingerPrintCnt 0
00:00:22|[libpdi] frontFaceRecognition 0
00:00:22|[libpdi] noCardReader 1
00:00:22|[libpdi] <-------System3_getSystemInfo-------<
[00:00:22 trace SecurityUnit:811372 333 CipherManager.cpp:45]the input num:3.
***
Program Build at :Aug 22 2022 02:15:40
***
[DHTS][Src/queue.cpp:1887]: CSchedManager init success
[DHTS][Src/api.cpp:244]: dhts lib startup, Status 1
[00:00:22 trace Infra:838285M 366 Thread.cpp:115]ThreadBody Enter name:Sock_Timer_Thread, id:366, prior:N64, stack:0x57d57c4c
[00:00:22 trace Infra:838285M 365 Thread.cpp:115]ThreadBody Enter name:MemoryUsage, id:365, prior:N64, stack:0x58557c4c
[00:00:22 info NetFramework:1094663 333 Debug.cpp:68]<NetFrameWork Debug>-------------------------------------------------------------------------------
[00:00:22 info NetFramework:1094663 333 Debug.cpp:69]<NetFrameWork Debug>- NetFrameWork Build:2022-07-26-13:54:54, Version:1094663 -
[00:00:22 info NetFramework:1094663 333 Debug.cpp:70]<NetFrameWork Debug>-------------------------------------------------------------------------------
[00:00:22 trace Infra:838285M 376 Thread.cpp:115]ThreadBody Enter name:NetFramework0, id:376, prior:N64, stack:0x52769c4c
[00:00:22 trace Infra:838285M 375 Thread.cpp:115]ThreadBody Enter name:NetFramework0, id:375, prior:N64, stack:0x52f69c4c
[00:00:22 trace Infra:838285M 374 Thread.cpp:115]ThreadBody Enter name:NetFramework0, id:374, prior:N64, stack:0x53769c4c
[00:00:22 trace Infra:838285M 373 Thread.cpp:115]ThreadBody Enter name:NetFramework0, id:373, prior:N64, stack:0x53f69c4c
[00:00:22 trace Infra:838285M 371 Thread.cpp:115]ThreadBody Enter name:Timer_Thread, id:371, prior:N64, stack:0x54f69c4c
[00:00:22 trace Infra:838285M 372 Thread.cpp:115]ThreadBody Enter name:NetFramework0 daemon, id:372, prior:N64, stack:0x54769c4c
[00:00:22 warn NetFramework:1094663 372 ThreadPool.cpp:329]InitConsoleDebug ok! run happy.
[00:00:22 trace Infra:838285M 370 Thread.cpp:115]ThreadBody Enter name

hts_IoDispatcher, id:370, prior:N64, stack:0x55769c4c
[00:00:22 info NetFramework:1094663 370 DhtsDispatcher.cpp:201]CDhtsIoCollecter::ThreadProc thread start...
[00:00:23 info NetFramework:1094663 333 NetThread.cpp:98]Create NetFramework thread pool success!
[00:00:23 info Unknown 333 Unknown:0]CPacketManager: malloc total:26214400 pagesize:1024blockCount:25600 ManagermentSize:512300
[00:00:23 info Unknown 333 Unknown:0]AddrRange:0x4fe6a400/0x5176a400)
[00:00:23 trace Infra:838285M 377 Thread.cpp:115]ThreadBody Enter name:RedirServer, id:377, prior:N64, stack:0x51f69c4c
[00:00:23 error Manager 333 CommonConfigManager.cpp:1773]CCommonConfigManager::readFileSec /var/tmp/pd/CustomConfig is not exist!
[00:00:23 warn Manager 333 CommonConfigManager.cpp:284]CCommonConfigManager::CCommonConfigManager() read customConfig file failed.
[00:00:23 error Manager 333 CommonConfigManager.cpp:1773]CCommonConfigManager::readFileSec /var/tmp/pd/CustomPathSensitive is not exist!
[00:00:23 error Manager 333 CommonConfigManager.cpp:292]CCommonConfigManager::CCommonConfigManager() read customConfigEncrypt file failed.
[00:00:23 warn Manager 333 CommonConfigManager.cpp:305]CCommonConfigManager::CCommonConfigManager() read sensitive config file failed.
[00:00:23 warn Manager 333 FileLog.cpp:1739]CFileLog::getLogsFromFiles,open(/mnt/mtd/Log/log.zip) failed
[00:00:23 warn Manager 333 FileLog.cpp:180]CFileLog::config,get logs from file(/mnt/mtd/Log/log.zip) failed
[00:00:23 warn Manager 333 FileLog.cpp:1739]CFileLog::getLogsFromFiles,open(/mnt/mtd/Log/logbackup.zip) failed
[00:00:23 error Manager 333 FileLog.cpp:183]CFileLog::config,get logs from bak file(/mnt/mtd/Log/logbackup.zip) failed
[00:00:23 warn Manager 333 FileLog.cpp:1739]CFileLog::getLogsFromFiles,open(/mnt/mtd/Log/log0.zip) failed
[00:00:23 warn Manager 333 FileLog.cpp:180]CFileLog::config,get logs from file(/mnt/mtd/Log/log0.zip) failed
[00:00:23 warn Manager 333 FileLog.cpp:1739]CFileLog::getLogsFromFiles,open(/mnt/mtd/Log/logbackup0.zip) failed
[00:00:23 error Manager 333 FileLog.cpp:183]CFileLog::config,get logs from bak file(/mnt/mtd/Log/logbackup0.zip) failed
00:00:23|[libpdi] >-------System3_getSystemInfo------->
Fail to get env dvname!
Fail to get env devOEM!
Fail to get env authcode!
00:00:23|[libpdi] Get authcode error
Fail to get env productDate!
Fail to get env peripheral!
00:00:23|[libpdi] Can't open /dev/pdcFinger
00:00:23|[libpdi] deviceChannel[0]: IPC
00:00:23|[libpdi] deviceType: IPC-HDBW4231F-AS
00:00:23|[libpdi] processorType: 33
00:00:23|[libpdi] hardwareVersion: 1.00
00:00:23|[libpdi] appAutoStart: 1
00:00:23|[libpdi] deviceClass: IPC
00:00:23|[libpdi] noPtz: 1
00:00:23|[libpdi] noSdCard: 0
00:00:23|[libpdi] noRTC: 0
00:00:23|[libpdi] bandWidth: 80
00:00:23|[libpdi] channelNum: 1
00:00:23|[libpdi] fingerPrintCnt 0
00:00:23|[libpdi] frontFaceRecognition 0
00:00:23|[libpdi] noCardReader 1
00:00:23|[libpdi] <-------System3_getSystemInfo-------<
[00:00:23 warn Manager 333 Unknown:0]init:93 use default cmos def path!
[00:00:23 info Manager 333 Unknown:0]use default CMOS definition!
00:00:23|[pdc] ERROR (RTC_readSram|291): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|450): Fail to read sram!
00:00:23|[libpdi] ERROR (PDI_rtcReadSram|157): Fail to ioctl rtc
[00:00:23 warn Manager 333 Unknown:0]readCmos:183 read CMOS failed: Label
[00:00:23 warn Manager 333 Unknown:0]initCMOS:252 read cmos LABEL failed!
[00:00:23 info Manager 333 Unknown:0]Src/MagicBox.cpp:CMagicBox:433 m_realDeviceType(IPC-HDBW4231F-AS)
00:00:23|[pdc] ERROR (RTC_readSram|291): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|450): Fail to read sram!
00:00:23|[libpdi] ERROR (PDI_rtcReadSram|157): Fail to ioctl rtc
[00:00:23 warn Manager 333 Unknown:0]readCmos:183 read CMOS failed: ExitTime
[00:00:23 error Manager 333 Unknown:0]Src/MagicBox.cpp:553 readCMOS CMOS_EXIT_TIME failed.
00:00:23|[pdc] ERROR (RTC_readSram|291): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|450): Fail to read sram!
00:00:23|[libpdi] ERROR (PDI_rtcReadSram|157): Fail to ioctl rtc
00:00:23|[libpdi] ERROR (PDI_getStartUpFlag|259): Fail to read rebootState from rtc
00:00:23|[libpdi] read RTC_SRAM_REBOOT = 0
00:00:23|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:23|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:23|[libpdi] ERROR (PDI_getStartUpFlag|268): Fail to write data to rtc
00:00:23|[pdc] ERROR (RTC_readSram|291): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|450): Fail to read sram!
00:00:23|[libpdi] ERROR (PDI_rtcReadSram|157): Fail to ioctl rtc
00:00:23|[libpdi] ERROR (PDI_startUpFlagCkCrc|367): read: RTC_SRAM_STARTFLAG failed
00:00:23|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:23|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:23|[libpdi] ERROR (PDI_setStartUpFlag|335): Fail to write data to rtc
00:00:23|[pdc] ERROR (RTC_writeSram|329): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|508): Fail to write sram !
00:00:23|[libpdi] ERROR (PDI_rtcWriteSram|208): Fail to ioctl rtc
00:00:23|[libpdi] ERROR (PDI_setStartUpFlag|343): Fail to write data to rtc
00:00:23|[libpdi] PDI_getStartUpFlag: 0
[00:00:23 info Manager 333 Unknown:0]CMagicBox::CMagicBox() getStartUpFlag 0
[00:00:23 warn Manager 333 Unknown:0]CMagicBox::setSubModuleInfo fail!
[00:00:23 info Manager 333 Unknown:0]CMagicBox:

nConfigAutoMaintain day = [2], hour = [2], min = [0], enable = [true]
00:00:23|[pdc] ERROR (RTC_readSram|291): rtc has trouble!
00:00:23|[pdc] ERROR (RTC_ioctl|450): Fail to read sram!
00:00:23|[libpdi] ERROR (PDI_rtcReadSram|157): Fail to ioctl rtc
[00:00:23 warn Manager 333 Unknown:0]readCmos:183 read CMOS failed: DSTTune
[00:00:23 warn Manager 333 Unknown:0]startDstTune readCmos failed! Load from config bDSTEnable: 0
[00:00:23 info Manager 333 Unknown:0]CMagicBox::startDstTune readCMOS DstTune flag is 0.
[00:00:23 error Manager 333 Unknown:0]CMagicBox::readFileSec /var/tmp/pd/ProductDefinition is not exist!
[00:00:23 error Manager 333 Unknown:0]CMagicBox::config read productDefinition file failed.
[00:00:23 error Manager 333 Unknown:0]CMagicBox::readFileSec /var/tmp/pd/ProductPathSensitive is not exist!
[00:00:23 error Manager 333 Unknown:0]CMagicBox::config read productDefinitionEncrypt file failed.
[00:00:23 warn Manager 333 Unknown:0]CMagicBox::CMagicBox() load product definition Resolution file failed.
[00:00:23 warn Manager 333 Unknown:0]CMagicBox::CMagicBox() load product definition language file failed.
[00:00:23 info Manager 333 Unknown:0]CMagicBox::m_systemInfo.noPtz == [1]
[00:00:23 info Manager 333 Unknown:0]CMagicBox::m_systemInfo.noSdCard == [0]
[00:00:23 info Manager 333 Unknown:0]CMagicBox::m_systemInfo.bandWidth == [80]
[00:00:23 info Manager 333 Unknown:0]Src/MagicBox.cpp:config:2404 set PD Device to IPC-HDBW4231F-AS
[00:00:23 error Manager 333 LanguageShorthand.cpp:50]CLanguageShorthand file is not exist!
[00:00:23 error Intelli- 333 Dh3Init.cpp:85]Please use initIntelliComponentLibrary() instead of function (initIntelliComponentLibraryIPC)!
[00:00:23 info Intelli- 333 Dh3Init.cpp:57]enter initIntelliComponentLibrary .......
[00:00:23 info Intelli- 333 Dh3Init.cpp:14]Dh3InitSD configLib
[00:00:23 info Intelli- 333 Dh3Init.cpp:21]Dh3InitSD configLib2
[00:00:23 trace Intelli- 333 HeatMap.cpp:189]isSupportHeatMap: bSupport[0]
[00:00:23 warn Manager 333 CommonConfigManager.cpp:472]CCommonConfigManager::getConfig FishEyeMode is Json::nullValue!
[00:00:23 trace Infra:838285M 378 Thread.cpp:115]ThreadBody Enter name:WatchDog, id:378, prior:N1, stack:0x4fdeac4c
00:00:23|[prc] Set WdtTimeout To WdtTimeoutMax:47721, instead !
safe_abn_unlocked_ioctl : No such cmd 1074033412
00:00:23|[libpdi] ERROR (System_setSafeAbnormalMonitorParam|9108): System_setSafeAbnormalMonitorParam : Failed to set monitor param
[00:00:23 warn Manager 333 AlarmManager.cpp:246]CAlarmManager:

nConfigSafetyAbnormalAlarm, 246, setSafetyAbnormalMonitorParam failed
[00:00:23 error SecurityUnit:811372 333 CipherManagerImpl.c:441]open file failed,the errstr:No space left on device.
[00:00:23 error Manager 333 UserManager.cpp:2285]CUserManager::writeFileSec fail m_cipherMnager
[00:00:23 error Manager 333 UserManager.cpp:87]Src/Compat/UserManager.cpp:87 param format error
[00:00:23 error SecurityUnit:811372 333 CipherManagerImpl.c:441]open file failed,the errstr:No space left on device.
[00:00:23 error Manager 333 UserManager.cpp:2285]CUserManager::writeFileSec fail m_cipherMnager
[00:00:23 trace Manager 333 Unknown:0]CConsole::registerCmd had been register!!
[00:00:23 error SecurityUnit:811372 333 CipherManagerImpl.c:441]open file failed,the errstr:No space left on device.
[00:00:23 error Manager 333 UserManager.cpp:2285]CUserManager::writeFileSec fail m_cipherMnager
[00:00:23 error SecurityUnit:811372 333 CipherManagerImpl.c:441]open file failed,the errstr:No space left on device.
[00:00:23 error Manager 333 UserManager.cpp:2285]CUserManager::writeFileSec fail m_cipherMnager
[00:00:23 trace Manager 333 Unknown:0]CConsole::registerCmd had been register!!
[00:00:23 warn Infra:838285M 333 Thread.cpp:411]this:0x323b720 too small stack size, StackSize:1024, adjust to 16k
[00:00:23 trace Manager 333 FileLog.cpp:191]CFileLog::attachFilter
[00:00:23 warn Manager 333 CommonConfigManager.cpp:472]CCommonConfigManager::getConfig Network is Json::nullValue!
[00:00:23 warn Manager 333 Unknown:0]CMagicBox::getDeviceSubClass DeviceSubClass empty !
[00:00:23 trace Manager 333 TelnetHelper.cpp:84]CTelnetConfigHelper:

nConfigTelnet(), m_cfgtelnet: null

[00:00:23 trace Manager 333 TelnetHelper.cpp:90]ConfigTelnet={
"Enable" : false
}

[00:00:23 trace Infra:838285M 379 Thread.cpp:115]ThreadBody Enter name:Console, id:379, prior:N1, stack:0x4f5eac4c
00:00:23|[libpdi] ERROR (NET_setTelnet|5816): telnetd is not exist!
[00:00:23 error Manager 333 TelnetHelper.cpp:123]setTelnet interface failed !!!!!!!!,123,Src/Helper/TelnetHelper.cpp
[00:00:23 error Manager 333 SSHDHelper.cpp:78]CSShConfigHelper::start, get ProductDefinition[SupportSSH] Failed || SupportSSH is false.
00:00:23|[libpdi] WARN : Device has no crypt chip!
00:00:23|[libpdi] English
[00:00:23 error Manager 333 Locales.cpp:154]Src/Locales.cpp:154 system has no supportLanguages.
====================== assert failed ==========================
backtrace f is NULL
Assert(0) failed
File <---> Src/Locales.cpp
Function <---> virtual bool Dahua::Manager::CLocales::config(const Json::Value&)
Line <---> 155
backtrace f is NULL
====================== assert failed ==========================
backtrace f is NULL

Time : Thu Jan 1 00:00:23 1970

=========================== TRACE START ===================================
Tid:333, Exception type : Assert failed
ARM_lr:76dcbd4b, ARM_pc:76dcbcde ARM_sp:7e80fd68.
[00010000-0119d000] sonia,0000018f 00000875
[011ac000-01489000] sonia,0000038f 00100873
[76266000-76267000] libutils.so.0,0000018f 00000075
[76276000-76277000] libutils.so.0,0000038f 00100073
[76279000-76291000] libgcc_s.so.1,0000018f 00000075
[762a0000-762a1000] libgcc_s.so.1,0000038f 00100071
[762a1000-762a2000] libgcc_s.so.1,0000038f 00100073
[762a2000-7630d000] libm.so.6,0000018f 00000075
[7631c000-7631d000] libm.so.6,0000038f 00100071
[7631d000-7631e000] libm.so.6,0000038f 00100073
[7631e000-76410000] libstdc++.so.6,0000018f 00000075
[76420000-76425000] libstdc++.so.6,0000038f 00100071
[76425000-76427000] libstdc++.so.6,0000038f 00100073
[76429000-764a8000] libimg_dsp_s3l_hf.so,0000018f 00000075
[764b7000-764b9000] libimg_dsp_s3l_hf.so,0000038f 00100073
[764ee000-765aa000] libimg_algo_s3l.so,0000018f 00000075
[765b9000-765c2000] libimg_algo_s3l.so,0000038f 00100073
[76948000-76953000] libalgicr.so,0000018f 00000075
[76962000-76965000] libalgicr.so,0000038f 00100073
[76965000-76968000] libalgh3a.so,0000018f 00000075
[76978000-76979000] libalgh3a.so,0000038f 00100073
[76979000-769be000] libalgae.so,0000018f 00000075
[769cd000-769d2000] libalgae.so,0000038f 00100073
[769d2000-769d6000] libaewdrv.so,0000018f 00000075
[769e5000-769e6000] libaewdrv.so,0000038f 00100073
[769e6000-769e9000] libpdbt.so,0000018f 00000075
[769f8000-769f9000] libpdbt.so,0000038f 00100073
[769f9000-76a12000] libamp.so,0000018f 00000075
[76a21000-76a23000] libamp.so,0000038f 00100073
[76a26000-76a7b000] libaew.so,0000018f 00000075
[76a8a000-76aad000] libaew.so,0000038f 00100073
[76b0b000-76b1d000] libz.so.1,0000018f 00000075
[76b2d000-76b2e000] libz.so.1,0000038f 00100073
[76b2e000-76b2f000] librpc.so,0000018f 00000075
[76b3e000-76b3f000] librpc.so,0000038f 00100073
[76b3f000-76c16000] libc.so.6,0000018f 00000075
[76c26000-76c28000] libc.so.6,0000038f 00100071
[76c28000-76c29000] libc.so.6,0000038f 00100073
[76c2c000-76c55000] libnl.so,0000018f 00000075
[76c64000-76c67000] libnl.so,0000038f 00100073
[76c67000-76c71000] libQRCode.so,0000018f 00000075
[76c80000-76c81000] libQRCode.so,0000038f 00100073
[76c81000-76c85000] libzzip.so,0000018f 00000075
[76c94000-76c95000] libzzip.so,0000038f 00100073
[76dcbcde]
[00ac3cf6] [00ab3cf6] sonia
[00ac423e] [00ab423e] sonia
[005c4d82] [005b4d82] sonia
[005b5e06] [005a5e06] sonia
[00044600] [00034600] sonia
[7e8147f8]
signr=11
img_get_statistics(1198): wait statistics timeout, statistics_ready = 1
Segmentation fault
####application exit:139, system will reboot!
upgrade forbidden
Date&Time: Apr 24 2019 08:01:55
Revision: 55769
Enter 'help' for a list of commands (dsh)

#ambarella_sd_irq SD_NIS_INSERT

Search

Search

DAHUA IPC-HDBW4231F-AS Bootloop

PinguMx

n3wb