Need camera mounted 100 feet from building.

L

Lakesteve124

n3wb
Sep 16, 2024
12
2
NY
I'm about to work on a project that involves mounting a camera at a lake that will be 100 feet from the power and internet source.

Trenching seems to be the only option.

I guess my main question is what will I need in terms of cable, and specific type of cable and conduit to shield from the weather.

Will will the signal degradation be at 100 feet?

The camera has not been picked out yet, but it should have an ethernet port.

Thank you all,
 
I use solid copper 23AWG cable in PVC conduit. Almost all of my cameras are more than 100' from the POE switch, some pushing 300', with no signal problems. If you choose to run 12 volt power instead of using POE, the power cable must be heavier gauge wire because of the higher current at 12 volts vs. POE voltage.
 
  • Like
Reactions: mat200 and Lakesteve124
tigerwillow1 said:
I use solid copper 23AWG cable in PVC conduit. Almost all of my cameras are more than 100' from the POE switch, some pushing 300', with no signal problems. If you choose to run 12 volt power instead of using POE, the power cable must be heavier gauge wire because of the higher current at 12 volts vs. POE voltage.
Click to expand...
I've never used POE. Does this require a special switch or amplification? My other installation is a Foscam wi-fi HT2 mounted to the house with two screws and plugged into the wall, so this is new territory for me.

I guess I should tack on another question - Recommendations on a camera for this? It will be at a sailing club, where members will use the cam to view conditions on the lake. It will need to be year round and will be in upstate NY where temps can go -20 in the worst "polar vortex" conditions that are not very common but do happen.. Needs to be RTSP ready for streaming.
 
Last edited:
I don't consider a POE switch to be special, they are pretty common and readily available. You can also use a POE injector that goes between the switch and camera to insert power. Personally I prefer to use a POE switch, it's just simpler. The majority of cameras represented on this forum are made by Dahua, and it would be hard to find one that doesn't support POE. You might get a lot of camera recommendations. I throw out that it should be either a turret or bullet camera. My cameras have occasionally seen -20 and never had a problem with it. The kind-of standard camera recommendation is this one
EmpireTech IPC-T54IR-ZE-S3 1/1.8" CMOS 4MP IR Starlight 2.7mm–12mm Vari-Focal Turret Security Camera
or it's equivalent bullet, but with more specific info on your application, there could be a better choice. I'm assuming you're not looking for a recorder, just live streaming.
 
tigerwillow1 said:
I don't consider a POE switch to be special, they are pretty common and readily available. You can also use a POE injector that goes between the switch and camera to insert power. Personally I prefer to use a POE switch, it's just simpler. The majority of cameras represented on this forum are made by Dahua, and it would be hard to find one that doesn't support POE. You might get a lot of camera recommendations. I throw out that it should be either a turret or bullet camera. My cameras have occasionally seen -20 and never had a problem with it. The kind-of standard camera recommendation is this one
EmpireTech IPC-T54IR-ZE-S3 1/1.8" CMOS 4MP IR Starlight 2.7mm–12mm Vari-Focal Turret Security Camera
or it's equivalent bullet, but with more specific info on your application, there could be a better choice. I'm assuming you're not looking for a recorder, just live streaming.
Click to expand...
Thank you! I will look into the POE setup. The camera will be a scenic one as well, local TV already uses my other cam on their weather segments, so it needs to be good quality. The cam will stream on iPcamlive and the player will be embedded into my website with the other cam. I live within 20 minutes of both sites.
 
You must log in or register to reply here.
Top Bottom