SD22204UE-GN DH_SD-Eos-Civil_MultiLang_PN_Stream3_V2.810.0000000.4.R.200509

E

EMPIRETECANDY

IPCT Vendor
Nov 8, 2016
9,009
26,187
HONGKONG
Big Upgrade


Firmware for models as below ONLY.

PTZ1C203UE-GN,
PTZ1C203UE-GN-W,
SD29204UE-GN,
SD29204UE-GN-W,
SD22204UE-GN,
SD22204UE-GN-W,


New Feature Description
1 No plug-in program phase
2: High-version browsers can play live view videos without installing plugins. 2 Support：Self-diagnose device failure, and then generate a failure code (if any) for troubleshooting.
3 Add RTP and TS multicast configuration interface.
4 The duration of the preset title displaying on the screen can be set to Disable, 5s, 15s, Display Permanently, or Custom.
5 Improve the quality of recorded videos transmitted to back-end devices (such as NVRs) with ANR function.
6 Users can connect the third party platforms to play live video of the device through RTMP protocol.
7 PTZ speed configured on the web interface only applies to manual control speed.
8 Special presets serve as the shortcut for some special functions switch or calling, and they no longer represent the location of the PTZ camera.
9 Move the Auto Tracking interface from PTZ Function interface to Smart Plan interface.
10 Snapshot by location: Only snapshots for certain locations will be stored.
11 Users can set the MTU value to ensure good data transmission according to the network.
12 Safety baseline 2.1 improves the program security level from authentication, confidentiality, integrity and other aspects.
13 Even transmission strategy: Transmit TCP and UDP streams evenly to alleviate the problem of stuck screen when network bandwidth is limited.
14 Add time zone and time settings during initialization process.


Fixed Bugs Description

After users configure FTP and click test, the system prompts that operation failed. Obtain FTP and SFTP names dynamically.
 

Attachments

  • Like
  • Love
Reactions: ddy64, rubinho, aristobrat and 2 others
Love not having to use a plugin to view cameras. I'm glad they are doing away with that.

PTZ startup preset still doesn't work that well. When the camera starts up, it doesn't go to the exact PTZ location I have set. It gets close but not exactly. I'm assuming the encoders that the PTZ motors use aren't very accurate.
 
biggen said:
Love not having to use a plugin to view cameras. I'm glad they are doing away with that.

PTZ startup preset still doesn't work that well. When the camera starts up, it doesn't go to the exact PTZ location I have set. It gets close but not exactly. I'm assuming the encoders that the PTZ motors use aren't very accurate.
Click to expand...
using BI or NVR?
 
@EMPIRETECANDY, I might have the same issue that @biggen mentioned. I've had it with all of the firmware versions.

After a reboot, the camera goes too high on all presets until I manually PTZ it down. After being pointed down, it will then hit all of the presets just fine until the next reboot.

Here's what preset #1 looks like after a reboot. You can see the camera is pointing too high up and the mount is getting in the view. If I switch to any other preset now, it will also point too high. If I switch back to preset #1, it comes back to this exact view.
1.png

If I manually PTZ the camera down like this....
2.png

.. and then tell it to go to any preset (like #1 below), it's fine and stays fine until the next reboot.
3.png
 
  • Like
Reactions: weigle2 and biggen
EMPIRETECANDY said:
using BI or NVR?
Click to expand...

Neither. Just recording to camera SD card.

Its never gone back 100% to the stored power up PTZ setting. Always a bit off. I can “fix it” by manually moving it around and then pushing the PTZ preset in the camera UI. That moves it to the correct area.
 
aristobrat said:
@EMPIRETECANDY, I might have the same issue that @biggen mentioned. I've had it with all of the firmware versions.

After a reboot, the camera goes too high on all presets until I manually PTZ it down. After being pointed down, it will then hit all of the presets just fine until the next reboot.

Here's what preset #1 looks like after a reboot. You can see the camera is pointing too high up and the mount is getting in the view. If I switch to any other preset now, it will also point too high. If I switch back to preset #1, it comes back to this exact view.
View attachment 62488

If I manually PTZ the camera down like this....
View attachment 62487

.. and then tell it to go to any preset (like #1 below), it's fine and stays fine until the next reboot.
View attachment 62486
Click to expand...

This is exactly what mine does. It goes too high on power up. If I move it around and then push my PTZ Preset, it will go right to the correct location.
 
  • Like
Reactions: EMPIRETECANDY and aristobrat
aristobrat said:
@EMPIRETECANDY, I might have the same issue that @biggen mentioned. I've had it with all of the firmware versions.

After a reboot, the camera goes too high on all presets until I manually PTZ it down. After being pointed down, it will then hit all of the presets just fine until the next reboot.

Here's what preset #1 looks like after a reboot. You can see the camera is pointing too high up and the mount is getting in the view. If I switch to any other preset now, it will also point too high. If I switch back to preset #1, it comes back to this exact view.
View attachment 62488

If I manually PTZ the camera down like this....
View attachment 62487

.. and then tell it to go to any preset (like #1 below), it's fine and stays fine until the next reboot.
View attachment 62486
Click to expand...
Mine does this too. It's been a problem since I installed it. I set up Preset 1 to be P: 0.0 T: 45.0 and when I go to Preset 1, then any other preset. it positions correctly until the next reboot. It's a PITA, but it works for now.
 
EMPIRETECANDY said:
Firmware for models as below ONLY.

PTZ1C203UE-GN,
PTZ1C203UE-GN-W,
SD29204UE-GN,
SD29204UE-GN-W,
SD22204UE-GN,
SD22204UE-GN-W,
Click to expand...

So not for SD22204T-GN ? Does anybody know the difference between that one and SD22204UE-GN ?

Anyway, thanks for any information…
 
tonin said:
So not for SD22204T-GN ? Does anybody know the difference between that one and SD22204UE-GN ?

Anyway, thanks for any information…
Click to expand...
22204UE-GN is 2mp starlight.
22204T-GN is normal 2mp ptz, they don't use the same firmware
 
Thanks for the Update!
Unfortunatley I am unable to activate IVS with a SD22204UE-GN-W - The Smart Plan screen is just empty:
1604094291473.png

Or am I missing something here that would allow me to enable IVS?
Smart Codec is disabled of course...


EDIT:

Sorry, it's my first PTZ Camera... I just figured out that I have to create a preset within the PTZ Submenu first. Stupid me :(

SOLVED :)
 
Last edited:
Hey,

I tried your Firmware, but still not seeing the "auto tracking" or "smart tracking" function in IVS - Intrusion or anywhere?
I have this camera: "SD22204UE-GN" (SD22204UE-GN)

But the latest firmware from their own website is 2.800.*.

Is it not activated for this model or do i have to do something specific before it works correctly?
 
inctor said:
Is it not activated for this model or do i have to do something specific before it works correctly?
Click to expand...
Looking at the spec sheet, it lists "N/A" for Auto Tracking, so looks like that model doesn't support that feature.
 
  • Like
Reactions: weigle2
You must log in or register to reply here.
Top Bottom