Recent content by AlbertoIt

  1. AlbertoIt

    PoE Switch vs PoE NVR

    I will try to compare Poe nvr and nvr+Poe switch. Poe nvr: +It is a little easier to setup (almost plugnplay) +If you think to add a ups battery you need just one for the nvr. less flexible placement (this depends on how many cameras you have) because all cameras cable must be connected to...
  2. AlbertoIt

    How do I get streams to display on my doorbell monitor?

    Do you mean how to find out the cameras IP address? Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  3. AlbertoIt

    VTNS1060A

    Question answered in this thread: Need help with VTO2202F-P Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  4. AlbertoIt

    Need help with VTO2202F-P

    In fact that's the problem. At the end I found this draw and that's exactly what I did. Thanks catcamstar, you're always helpful. By the way, the vto2202f has a much better camera than the older vto's! Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  5. AlbertoIt

    VTNS1060A

    Hello guys, in my intercom system I have the vtns1060a switch. Now i'm going to replace my broken vto2000a with a vto2202f-p. The doubt is can I connect the new vto to the vtns directly? I have this doubt because I have found the draw below. Apparently the vtns is a passive switch so could be...
  6. AlbertoIt

    Need help with VTO2202F-P

    Ok, I'm definitively an idiot...I was trying to connect to a non Poe port of the switch...it seems to be ok connecting in the right port. But I still have a question. Could I damage this vto if I connect to the vtns1060a? I'm asking because I found this (see picture) in a UK website. Inviato...
  7. AlbertoIt

    Need help with VTO2202F-P

    Hello guys. I have bought a new VTO2202F-P that was intended to replace my broken VTO2000A. I wanted to test it before mounting in its place so I connected it to my VTNS1060A but it didn't show anything....then I tried to connect to a Poe switch and nothing happened as well. Finally I tried to...
  8. AlbertoIt

    Powering 2-Wire VTH1550CHW-2 without VTNC3000A

    I'm not expert but I don't think it is possible because, besides the powering matter, the vth's couldn't communicate with the vto without the vtnc. Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  9. AlbertoIt

    PFA 137 vs PFA 130e

    My mistake sorry, you are completely right. I have just checked twice with accessories selector and they are compatible. Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  10. AlbertoIt

    PFA 137 vs PFA 130e

    According Dahua accessories selector they're not compatible but if you say so I believe :) Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  11. AlbertoIt

    PFA 137 vs PFA 130e

    Are you sure that the pfa130e is compatible with hdw5231r-ze? Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  12. AlbertoIt

    How to wire from VTH/Door for unlocking my front door ? (2 VTH and 1 VTO)

    Yes, you don't need an extra unlock button unless you don't want to have one (i.e. nearby the door as I have). Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  13. AlbertoIt

    How to wire from VTH/Door for unlocking my front door ? (2 VTH and 1 VTO)

    Yes but remember that vto can't give power to the electric lock, so you need a power source too. Inviato dal mio Redmi Note 5 utilizzando Tapatalk
  14. AlbertoIt

    How to wire from VTH/Door for unlocking my front door ? (2 VTH and 1 VTO)

    The electric lock is controlled by vto not directly by vth, so you have to connect it to the vto. Inviato dal mio Redmi Note 5 utilizzando Tapatalk
Top