Recent content by Dudleydogg

  1. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    but it misses, thats what i saw why it took me a minute to figure out, I would get detections then it would gag and miss a few and recover. I did what the guys suggested above and working good now.
  2. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    thank you guys I believe I have it working again getting tags at my gate no problem service not crashing during detection.
  3. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    I did a clean install and it finally shows modules after restarting service but i have this .net one just in limbo
  4. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    I have to ask this one also, Code Project was in the Wind, Shut down, Blue Iris leaning to another Blue Candle option, then all sudden Code project has update and Modules install again, and their site no longer says Woe is me were done, any one see any news about this are they back or just a new...
  5. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    so i have been using Yolo 5.6.2 but its also prompts for yolo .net did any one else also install those versions of Yolo?
  6. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    Currently re-installing with the tic box to remove all data and modules
  7. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    Thank you i will give that a try, I did update .net so far its holding but waiting for a car to go past the gate and see if it dings. Thank you for the comments.
  8. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    I did install over it not a clean install, even kept the modules, Bad Idea? should I do new version again clean install then pick my modules?
  9. Dudleydogg

    Updated to the Latest Version of the Code Project,Server version: 2.9.5 Crashes each time object is detected

    I updated today and stopped getting reliable information. Each time I check the status, it's in a "Lost Contact" State. Has anyone else updated and has a similar issue? I just updated .Net even though the installer did some other versions also to see if that was it. also downloaded previous...
    • Dudleydogg
    • Thread
    • blueiris alerts codeproject ai
    • Replies: 19
    • Forum: AI
  10. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    you can access a cloud key or docker container running your controller locally. it just wont ever update and you would need local user/pass
  11. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    Funny Story, I put the cloud key on same vlan as all the hik cameras, it found them and adopted and Logged in, then I put cloud key back on original vlan and they all stayed connected.
  12. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    so for those who ran into my issue where I could not "Manually adopt" always failed, I put the cloudkey on same vlan as the cameras, meaning I lose all my other network gear, Ignore that adopt all the cameras, then change the IP back to original cloud key vlan and all the HIK cameras re...
  13. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    Ok so i got the Hikvision camers to work but I realize there are no detections whatsoever its just constant record, is what also same for everyone?
  14. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    OK i put a couple cameras on same vlan and sure enough the populated clicked adopt and failed till I enabled the username&token option. i have only 2 cameras that have that feature in onvif so I either need all new HIK LOL or switch to UI and be done with it.
  15. Dudleydogg

    HUGE RUMOR: Unifi Protect will support ONVIF cameras (like from HIK/Dahua)

    all the cameras communicate with vlan 1 because all my viewers are on vlan 1, I can ping the camera from the Unifi ssh console, The error is instantaneous. like its didn't even try to authenticate just instant "invalid credentials" ill put a camera on same vlan as uniif and see if anything kicks
See more
Top Bottom