Recent content by iveco300

  1. I

    Older Dahua Webcam visible in BlueIris but their webpages are not loading

    hello I have the same problem after updating the firmware on a ptz when it is connected to nvr no longer works the webgui instead just restore and connect the cam directly to the pc works.
  2. I

    hello I maybe understood the problem I restored connected directly to the cam with the pc then I...

    hello I maybe understood the problem I restored connected directly to the cam with the pc then I entered the webgui and it worked. when i reconnect the cam to the nvr the problem comes up again so i think it is nvr's fault it seems almost a security lock with https certificates.
  3. I

    small criticism but before releasing updates dahua does not check if they work ??

    small criticism but before releasing updates dahua does not check if they work ??
  4. I

    hello thanks for the answer but I have tried and tried several times it doesn't work and I...

    hello thanks for the answer but I have tried and tried several times it doesn't work and I noticed that the metadata also doesn't work. is there a particular procedure for updating? i tried via nvr then with configtool but nothing. if you have the previous firmware i try to go back. thanks
  5. I

    hello andy I would need help about a ptz 6al433xa I updated the firmware found on the site dahua...

    hello andy I would need help about a ptz 6al433xa I updated the firmware found on the site dahua DH_SD-Prometheus_MultiLang_NP_Stream3_V2.812.0000032.2.R.220804 after the reboot I reported the standard settings but when I enter with the web page I have no video streaming. while through nvr or...
  6. I

    prometheus firmware

    these are the files in the folder which one should I use for updating?
  7. I

    prometheus firmware

    I downloaded the new firmware for sd6al433xa heavy 800 mega bytes with the entire two files .bin one update.bin and the other allupdate.bin which one should i use? someone knows
  8. I

    NEW SD59225U-HNI Latest New Firmware SD-Eos_MultiLang_PN_Stream3_V2.812.0000007.0.R.210706

    hello everyone yesterday I updated with this latest firmware DH_SD-Eos_MultiLang_PN_Stream3_V2.812.0000009.0.R.211011 the ptz 59430 and I could no longer enter the interface web.la cam starts and I see it on the network but I can not enter I tried all tftp, configtool, uart ssh nothing closes...
  9. I

    Pink image

    ciao a me la stessa cosa è successa solo che si è fermato con il filtro chiuso, quindi immagini normali durante il giorno ma nessun infrarosso di notte
  10. I

    SD59225U-HNI startup motor skipping

    Hello to all. for a couple of days I have the same problem and in my opinion due to the latest firmware update. what do you think?
  11. I

    Firmware downgrades via RS232?

    Yes you can go back to old firmware with tftp without rs232. Watch post where it is explained how to do
  12. I

    Review-I'll be the guinea pig for the new SD59225U-HNI PTZ.

    Has anyone tried to verify with the integrated upgrade if there are updates? I am at 09/2016 firmware
  13. I

    IR ranging issue's with SD59225U-HNI after firmware update.

    updating I now reported that they know about bug i and they are about to fix it. I hope this is so because the new firmware works fine except IR. with 2016 firmware the autotrack is non-existent ..
  14. I

    IR ranging issue's with SD59225U-HNI after firmware update.

    I received the news from my reseller and says these cams do not have to update. but then why publish new firmware for these cams ??? it seems ridiculous to me
  15. I

    Sd59230 can't get smooth video recording

    Another proof that you can download the video on PC and check if it is slider. If it is fluid it means there is a LAN network problem See also how many mega bytes and video If there are so many in tot seconds, there are probably too many details or too much saturation. .
Top