John Williamson's latest activity
-
John Williamson replied to the thread HIK camera toggles between night mode and non night mode every 10 seconds.Two things to try: In Image > Display Settings make sure you have the 'Light Brightness Control set to Auto and not Manual at 100%... -
John Williamson reacted to Pike25lb's post in the thread Pyronix enforcer alarm bell warning with
Like.
Thanks John I deleted it relearn it now has 100% signal hopefully that has fixed my issue -
John Williamson replied to the thread Hikvision camera settings.15 metres? The standard works cherry picker only used to do about 10 or 12... Are the cameras connected to a Hikvision NVR? If so...
-
John Williamson replied to the thread Pyronix enforcer alarm bell warning.Yeah while it's in fault like that you'll only see 0. When you relearn at the panel you should see 100. Once it's back in its final...
-
John Williamson replied to the thread Pyronix enforcer alarm bell warning.Pop the module out, delete it and relearn it at the control panel before reinstalling it. Once reinstalled run the signal strength test...
-
John Williamson replied to the thread Pyronix enforcer alarm bell warning.It's the battery. I've seen this happen on a few of my sites. No low battery warning, just a poll fail or supervision fault. If you...
-
John Williamson reacted to Afranze's post in the thread New 2CD2387G2-LISU/SL not auto switching to supplement light with Like.
No the problem I found was it wasnt detecting motion. Where the camera was pointing and where the motion was happening was on both very...
-
-
John Williamson replied to the thread Britain is Lost.I've had a brief look through some of the tweets and posts linked. Most of it is complete crap, lies and misinformation. I'm astounded...
-
Can't seem to quote specific replies on this forum(?). Nobody is being jailed for memes, stop peddling garbage designed for the...
-
John Williamson replied to the thread New 2CD2387G2-LISU/SL not auto switching to supplement light.It's likely your cameras are staying in colour as the shutter speed is set too slow and there's sufficient light. I think (not tried)...
-
John Williamson reacted to machineage's post in the thread Cams / NVR Arrived - Have I Made a Mistake :-/ with Like.
It's late here - but I've managed to install one of the cams! :) There's no way I could have gotten this far without the help of...
-
John Williamson replied to the thread DS-2CD2387G2P-LSU/SL - Power Supply?.LSU/SL has internal mic and speaker. As already mentioned: For main stream set to Video and Audio For sub stream set to Video and...
-
John Williamson reacted to alastairstevenson's post in the thread Cams / NVR Arrived - Have I Made a Mistake :-/ with Like.
Not on the hub web GUI, unless they've added that capability on the Hub 5 after user feedback. It's possible on a rather cryptic URL...
-
John Williamson replied to the thread Cams / NVR Arrived - Have I Made a Mistake :-/.They're fine.
-
John Williamson replied to the thread Cams / NVR Arrived - Have I Made a Mistake :-/.Network wise, no so long as you've set the IP, Gateway and DNS
-
John Williamson replied to the thread Cams / NVR Arrived - Have I Made a Mistake :-/.You can change the default range on the VM Hubs but it's best to leave it. What you might want to do now is to change the IP address of...
-
John Williamson replied to the thread Cams / NVR Arrived - Have I Made a Mistake :-/.As others have said this is simply caused by the NVR IP address being on a different subnet: Just alter the IP address of the MacBook...
-
John Williamson reacted to machineage's post in the thread Cams / NVR Arrived - Have I Made a Mistake :-/ with Like.
They actually arrived into the UK in just two working days - it was the weekend that held up delivery. Incredible service from...
-
John Williamson replied to the thread Cams / NVR Arrived - Have I Made a Mistake :-/.Only 5 days total to the UK? That's great service. I was going to order a couple of these cameras myself but have been put off by the...
