Recent content by MythicFrost

  1. M

    Reset intercom/doorbell password

    Hi guys, I'm hoping you might have an idea of how I can reset my intercom (x2) & doorbell, so I can get them working over WiFi again (e.g., being able to answer the call on the phone). I downloaded the hikvision software (IVMS-4200) onto my computer, connected, then I changed the default...
  2. M

    5.5.6 - March 12, 2022 - Major UI3 browser client release, timeline playback is now available!

    Yeah, it usually uses sub stream when viewing all of them at once since they are small, but one I select one and it takes up the full viewport, it normally goes to high quality but recently it stays sub stream quality.
  3. M

    5.5.6 - March 12, 2022 - Major UI3 browser client release, timeline playback is now available!

    I also noticed recently I have been unable to view the main stream. I only see the sub stream (low quality) even when solo viewing a single cam.
  4. M

    Can a VLAN be setup on a single port on the EdgeRouterX for a single computer?

    Thank you! Just setting the PVID to 5 for that port (no VLANID) put it on to the desired VLAN I wanted.
  5. M

    Can a VLAN be setup on a single port on the EdgeRouterX for a single computer?

    Hi, I thought it would be possible to plug my desktop into ETH4 and have it setup as a VLAN, but I've failed doing that for the last couple of hours. I finally get internet working through ETH4 but my IP is in the 192.168.1.1/24 range which is the switch0's IP range. My understanding was the...
  6. M

    Can't see cam on network

    Thank you! I'll give it a read.
  7. M

    Can't see cam on network

    Ohhh yeah that sounds like a real headache. I'd like to avoid that!
  8. M

    Can't see cam on network

    Will do, thanks! I may need to do some tinkering with the DHCP server for the range but I think I can do that without issue.
  9. M

    Can't see cam on network

    Roger that. Thanks for the tip! I'll make sure to leave them as static and I'll set them on a range that can't be used.
  10. M

    Can't see cam on network

    Just curious why that is? They will be on a VLAN that drops all traffic to the internet/network with the blue iris rig as an exception. That was my plan, anyway.
  11. M

    Can't see cam on network

    Yep, I'm going one step at a time. Next up I will try and see if I can make the device get assigned its IP over DHCP otherwise I can set a static IP for it on 192.168.20.x. But basically I'm in the middle of fixing how my whole network will work.
  12. M

    Can't see cam on network

    Yep, I disconnected WiFi. Although the cam is still connected to the switch (as I don't have anything to power it without the PoE). It's working nicely now. Thanks for your help! Now I just need to figure out how to focus it... haha.
  13. M

    Can't see cam on network

    Considered that but don't know how to power it without PoE Yep, just did that! I tried the switch's IP and it didn't work, so I tried setting it to something on the 192.168.1.x network and pinged the camera. Going to run ConfigTool now. Thanks for your help!
  14. M

    Can't see cam on network

    WiFi connects on 192.168.20.x. Router divies out 192.168.1.x, 192.168.10.x, and 192.168.20.x depending on how devices are connected. I opened command prompt and ran arp -a which showed what I believe is the network interface of my WiFi and of my switch. Listed under the switch is...
  15. M

    Can't see cam on network

    Hi, I just picked up an EmpireTech IPC-T5442T-ZE from Amazon. I have BlueIris freshly installed on my PC (it is an iMac running Windows 10). I have connected my (unmanaged) NETGEAR GS108LP into the PC via Ethernet. (It is connected to WiFi for internet.) I have a cat5e cable (temporary)...
See more
Top Bottom