Recent content by rdxny

  1. R

    2025 New Arrivals From EmpireTech

    will this have animal alerts in IVS?
  2. R

    Using the "experience database" in the 5442 s3 cams

    no one has any knowledge of this (below) ? Just trying to figure this out! @steve1225 @Wildcat @wittaj ???? This seems to be working, though it will take a while to see if it is really learning anything. One question remains: When I first tried it, when I selected a clip in the Experience...
  3. R

    Using the "experience database" in the 5442 s3 cams

    Damn, so it is! I missed that, and it wasn't needed with BI.. so... Many thanks, now working, I will begin trying to work the experience database now:) Much appreciated, you and Steve!
  4. R

    Using the "experience database" in the 5442 s3 cams

    I normally record OnVif to BI. I was able to record "general" full time to the sd card, but I still can't figure out where to tell the Web Setup to record events to the sd card... they aren't showing up... . I dont see any destination setting in the IVS portion...
  5. R

    Using the "experience database" in the 5442 s3 cams

    ok, will try that! No way to do both? ah, ok then, that seems to be the source of my issues now. I'll reconfigure it and test. I was thinking a full res full time record on cards that recycled itself would be handy, in addition to the continuous sub plus alerts I use now on BI. Continuous...
  6. R

    Using the "experience database" in the 5442 s3 cams

    hmmm.. might be getting closer: If I search in record: search video, they all show when using "all" or General". But if I select tripwire or intrusion (the two zones I have set up in IVS), I get nothing. So I guess my IVS is set to send to Onvif but not going to the sd card? (set for General...
  7. R

    Using the "experience database" in the 5442 s3 cams

    Yes, I think I am doing that! The clips show (as local storage) in the record: search.... I THINK they are on the sd card tho I see no sure way to confirm that, other than it says "local storage" and the sd card free space drops accordingly. They clips just dont show in the experience database...
  8. R

    Using the "experience database" in the 5442 s3 cams

    Steve: The events show in the Record: Search just fine. But nothing shows in the Ai/IVS/Global/ Experience Database/Details/import videos/search. Following Andy's video, that's where I need to select a clip to learn?... And I see no way in the main record/search part, where the clips do show...
  9. R

    Using the "experience database" in the 5442 s3 cams

    Thanks Steve, I don't have an NVR (just blue Iris)... IVS is set up to send to BI thru OnVif. So My web setup doesn't show AI-View Events-IVS level... Ai just goes to rule config and global, which are both set up (i think.. below... they work with BI), I just don't seem to be populating the...
  10. R

    Using the "experience database" in the 5442 s3 cams

    I'm trying to set up the Experience Database in my 5442 s3 cams (with the 12/24 firmware) to do the self learning to filter animals better. I installed an SD card to the cams, and following Andy's video, I can see the clips in the Record/ search video tab in the web setup. (time plan set...
    • rdxny
    • Thread
    • Replies: 16
    • Forum: Dahua
  11. R

    IPC-T54IR-ZE-S3 Motion Detection via IVS not working properly

    I think you might be confusing the box size and boundaries. The Min box square just defines the trigger size. Anything smaller than the box won't trigger (in theory). It doesn't matter where that box is when you draw it, just how big. The boundaries for tripwires or intrusion are another...
  12. R

    IPC-T54IR-ZE-S3 Motion Detection via IVS not working properly

    Thanks Wittaj, I do set Min to avoid squirrels, just trigger on deer. But that isn't reliable... subject size varies with distance, so a large min size might be appropriate close to cam, but too big further away. I'll try 0,0 and see how that works. Yorkman, the min size box is just to the...
  13. R

    IPC-T54IR-ZE-S3 Motion Detection via IVS not working properly

    Wittaj: Why min size of 0,0? Wouldn't that give more triggers (of small animals) than a larger min size?
  14. R

    I need help with the IPC-Color4K-T180

    Well, probably! I also had tried many things, mostly regarding the ethernet cable, with no change till I read this thread: https://ipcamtalk.com/threads/ipc-color4k-t180-intermittent-no-signal-in-bi.72212/page-3 That one setting allowed me to go from dozens or more connection errors a day to...
  15. R

    I need help with the IPC-Color4K-T180

    I had the same issue with that same cam, solved by checking "on" the "Decoder Compatibility Mode" in BI video settings
See more
Top Bottom