Search results for query: static route 3 things

  1. The following words were not included in your search because they are too short, too long, or too common: 3
  1. alastairstevenson

    [Help] - Cannot use SMTP on my HFW5442T-ASE (Loryta IPC-B5442T-ASE) but can use on my NVR...

    Not necessarily so, as the song goes. https://ipcamtalk.com/search/135569/?q=static+route+3+things&c[users]=alastairstevenson&o=date And I'd expect Dahua NVRs to behave in the same way. It would be interesting if someone could check this out ...
  2. alastairstevenson

    ISAPI Unauthorized?

    Given virtual host is active, as you have proven, you should be able to access the NVR PoE-connected cameras directly with a small change to your network routing, instead of going via the NATed connection. This should work better. 3 things required: The PoE-connected camera needs to have the...
  3. alastairstevenson

    Gmail Setup .... 3Test" Fails

    This is what you need as the way to gain normal access to cameras connected to NVR POE ports, and for them to access the internet to send email etc ... 3 things needed - Virtual Host enabled on the NVR. Cameras must have the NVR PoE interface as the default gateway, usually 192.168.254.1 To do...
  4. alastairstevenson

    Accessing Hikvision API to change setting on DS-2CD2342WD-I ??

    It might be worth trying this when accessing the cameras directly at their actual IP address as opposed to using the NVR NATed address. There is a way to gain normal access to cameras connected to NVR POE ports - 3 things needed - Virtual Host enabled on the NVR. Cameras must have the NVR PoE...
  5. alastairstevenson

    I can not access to NVR connected camera

    Assuming that you are using the NATted connection provided by the NVR Virtual Host facility : If it's the NATted access that's getting in the way of the ISAPI call, it may be worth experimenting with direct access to the cameras at their actual, not NAT, address. To do this you need 3 things...
  6. alastairstevenson

    Trying to set up nethdd with SMB, not working at all!!

    There is a way to gain normal access to cameras connected to NVR POE ports ... 3 things needed - Virtual Host enabled on the NVR. Cameras must have the NVR PoE interface add the default gateway, or 192.168.254.1 To do this you'll need to have the PoE channel in manual mode to stop the NVR...
  7. alastairstevenson

    How to get Hikvision camera connected to POE ports of Hikvision NVR to access WAN (WWW) ?

    Yes, that's correct. For a Hikvision NVR, 3 things needed to let PoE-connected cameras access the internet so they can send email, access ntp etc. - Virtual Host enabled on the NVR. - Camera default gateway=NVR PoE interface IP address. You have this already, you have them set to 192.168.254.1...
  8. alastairstevenson

    2 hikvison nvrs

    It can also be done with cameras that are connected to NVR PoE ports, if the NVR has the 'Virtual Host' facility, and if a 'static route' is added to the LAN gateway. Multiple how-to posts on the topic. I have a 7816N-E2/8P as a primary NVR with a 7816N-E2 and a QNAP NAS both accessing the...
  9. alastairstevenson

    How do I access camera on different subnet?

    Do you have 13Virtual Host' enabled on the NVR. That's fine for camera web GUI access. If you want to go further, for full access: If this is 'how to access Hikvision NVR PoE-connected cameras from the LAN', there are quite a few posts on the topic. The essence is as follows:
  10. alastairstevenson

    Full access to cameras via Hikvision NVR?

    Multiple how-to posts on this topic - example:
  11. alastairstevenson

    DS-2CD2335FWD-I - Hikvision Ultra Low Light 3M camera

    If you're inclined to experiment - you can access PoE-connected cameras directly on a Hikvision NVR. 3 things required : Enable 'Virtual Host' - the tick box under web GUI Network | Advanced Settings | Other. This implicitly activates the Linux kernel 'IP_forward' (not to be confused with port...
  12. alastairstevenson

    SOLVED, FTP picture upload through the NVR ?!

    You need 3 things configured to allow Hikvision PoE-connected cameras to reach the internet: Assuming the NVR firmware is new enough to have this feature, activate 23Virtual Host'. From what I recall, it's under Network Configuration, Advanced Settings. This provides a set of direct-access links...
  13. alastairstevenson

    LTS virtual host with Dahua camera

    Does it work with any other cameras on the NVR? I have 3 non-Hik cameras on a Hikvision 7816 NVR which work OK when their HTTP port is set to 80, but not other values. What's the HTTP port on your Dahua? Assuming Virtual Host on the LTS firmware operates in the same way as the Hikvision...
  14. alastairstevenson

    Recording one hikvision NVR on another?

    That's not a valid configuration - the channel numbers don't refer to the NVR channels, I think they are used on some of the higher-end IP cameras. There are a couple of things you may be able to do. Do you need to connect the cameras to the 2nd NVR as cameras (eg with motion detection), or as...
  15. alastairstevenson

    Camera snapshot interval FTP from behind the NVR

    3 things needed: First. The cameras on the PoE ports will have an invalid default gateway set - if using 'Plug30Play31 the GW will be set the same as the NVR LAN NIC. This is not accessible to the cameras - the default GW needs to be on the same subnet as the camera itself. On the assumption that...
  16. alastairstevenson

    Expert Motion Detection

    OK, a couple of things to check. In the camera, with an internet time service such as time.windows.com set as the NTP service - check if the 32Test33 button gives 34success35. If so - that36s a good indication that both name resolution and connectivity are working OK. If not - try replacing the...
  17. alastairstevenson

    Anyone changed the NVR default network to avoid static routes on router Fend/Alastai?

    Re: Anyone changed the NVR default network to avoid static routes on router Fend/Alas I must admit I have not tried changing the NVR PoE network IP addresses to be in the same range as the LAN addresses to see what would happen. I suspect to make that work, you37d have to connect one of the PoE...
  18. alastairstevenson

    email alerts to attach image on DS-7108N-SN/P or get camera to communicate outside?

    Re: email alerts to attach image on DS-7108N-SN/P or get camera to communicate outsid Yes, that38s correct. But you39ll probably need to have the PoE port configured as 'Manual' instead of 'Plug43Play' so the NVR doesn't change it back to be the same as the NVR default gateway. But you need a...
  19. alastairstevenson

    Remote access cameras on NVR

    From one of a few recent discussions on that topic: And a how-to from a while back. If you have 'Virtual Host' you don't need to activate the kernel 'IP forwarding', handy as it's back to default after a reboot...
  20. alastairstevenson

    My first attempts have failed..

    When the camera is on the separate network segment that the PoE ports use, by default it's traffic will not reach the internet. You need routing information and name resolution for that to work. I would guess that if you set an internet time source (eg time.windows.com) in the camera config, the...
  21. alastairstevenson

    Hikvision DS-7616NI-SE/P Firmware Update

    Hello aster1x - I don53t mean to confuse, apologies. But I do admit that I like tinkering around with these things, so what I did on my setup may not be suitable or useful to all. But hey, it works OK for me, as my NVR is on top of some wall cupboards in a utility room on the end of a gigabit...
Top