Search results

Thank you for your quick response I am doing them one at a time as above and accessing them through a browser with there IP address. After posting I changed the second cameras IP address and then rebooted NVR and hey presto the video feed has appeared on the second one. The only thing is it...

Well guys resetting them has gave me access to them but having issues getting them back on the NVR. First one goes on fine but when adding the second on the status it just says connecting and will not connect but I can connect to it through web browser. Any suggestions?

Yeah that's why I want nothing to do with them could just about replace all the cameras and NVR at that price. Will do will take what photos I can but all the cameras are at height so might just be blurry photos of me falling back to earth.lol

Quarterly I believe

Haha I shall pay you in gratitude and GIFs ........ But the forum does not let me upload GIFs. Lol

They start at £200 for remote support

Thankyou guys shall get this done tomorrow and when the company phones me again asking if I want to take out the maintenance package I can politely tell them where they can go.

Take it factory reset on the cameras is on the boards in the cameras? I.e. hold button disconnect power, keep holding button power up again.

I have recently bought a property with 4 Hik vision cameras and NVR with the property I have reset the admin password on NVR but do not have the camera passwords to allow me to connect them the previous owner was in a maintained contract with a company which I have no obligation to continue with...

Yes I can

Although when I first add it it says username or password is incorrect. Is it possible there is a previous password from previous owners stopping me connecting?

Thankyou for this. This is what I have been doing but it is still saying network is unreachable. Apart from it does not bring up a box to set admin password.

It is a hikvidion ds-7604NI-k1/4 with 4 POE ports but cameras are connected from switch to LAN port. I I quiet sure it will be the settings are not set to work from the LAN port I have attached photo of I.P on the NVR screen of the cameras and of the added devices I just can not figure out...

Hi everyone Got a strange one and hope you can all help. Got a four camera set up. They are all at a distance from NVR (all hik vision) so have two POE switches in the system. Other day it came up with no link on all four cameras on monitor and hik vision app. Checked all switches all...

Oh that stuff I used was direct burry luckily I had buried a duct under the ground to run it in which has saved me a lot of time and head ache the day The CCA must work on short runs or you would think it would not even be on the market. That said I would not use it on short runs now either so...

@wittaj and @looney2ns I said I was going to hold you both responsible if the new cable did not work so I had better give you the credit for the camera working. Ripped out the CCA wire and replaced with fully copper run direct from the original switch and tada the camera works, no lag, no...

I am planning to do away with the second switch and run cable direct from original switch now as it should be able to handle a 85m run on the copper IMO.

Thanks guys. Well I have just ordered 100m of 23AWG pure copper cat 6 cable and done an accurate measurement and it is only 85m from the original switch so I shall install new cable and if it doesn't work can I hold you both responsible for it???? ;);)

You know those times you ask a question and think you know the answer your going to get but hope someone gives you another well this is the answer I wasn't wanting. :facepalm::facepalm::facepalm::facepalm:

Aww naw. I really don't want to run new cable would a decent switch make it work?

It is Cat 6 24 gauge CCA terminated to 568B RJ45s.

How could I check/correct this? Can I manually program the port on the switch?

You are probably right but even without the camera plugged into the new switch it is kicking the three cameras off the original switch

They are all PTZs

Thanks for the reply. Please see below for equipment models: NVR. Hik vision DS-7604NI-K1/4P Original switch. ip com f1109p New switch yuanley ys2041g-p So the feed from the original switch comes back to the house and into a Netgear TL-SG105 switch which then...

Hi everyone First time posting here looking for a bit of help have a 3 camera setup all hard wired using poe. So it is NVR to a 8 port POE with three cameras they all work great trying to add a fourth which is around 100m from first switch when tried the cera would power on and go through...