Search results

Hi alastairstevenson, Same status here for me. How could I get out of this ? flashing the Rom ? any tips ? Rgds,

@alastairstevenson this is what I have ... i am hearing the camera booting and it is stuck like that. The bootloop last few seconds after the message [10-03 19:22:41][pid:343][UNI_IF][ERROR] ########motor app onl���� ��[?0��ap������� �� camera switchs off alone

[10-03 19:21:22][pid:343][UNI_IF][ERROR] �b�8002000���[10-�a���appweb: 1: Starting host named: "::" U-Boot 2010.06-143514 (Aug 27 2015 - 15:08:47) U-Boot code: 80700000 />?0�>¿ ����> ����?Net: Detected }A�������>�����H 0 Trying eth0 +�k��on port 0, speed 100, full duplex 9U1�ethaddr| not...

Hello @alastairstevenson, Here is what I have in loop: U-Boot code: 80700000 -> 8070F>?T >Net: Detgcte>x>eH 0 Trying eth0 +kon port 0, speed 100, full duplex 9U1ethaddr| not found tftpserver booting from sec partition... /nand/uImage to 0x80007fc0... B+ʪu5...

ok I've ordered it. I hope to finally get out of it :D

^^ah indeed, it is a 4pins 1.5mm. ^^then I need an adaptor because my 4 pins are too big to fit. ... ok I ll try to find that and test it again.

alastairstevenson, Here is what I have, check the pictures.

HI, I was overloaded so was not able to test the procedure earlier. I am getting back to it today. I am not sure about the way the pins should be connected to the camera. I check the link you shared. only 3 pins out of 4 are used correct ? first of all, I am not sure about the correct pins...

Hello alastairstevenson, I ve received the converter :) ... would you guide me to the procedure in order to fix my issue ? thx in advance :)

OK ... I ve ordered it. unfortunately, delivery is in 1 month. Could you help with the procedure ?

Looks like this is the one: https://www.amazon.fr/Convertisseur-Adaptateur-PL2303HX-Serial-Arduino/dp/B00E8C1G1I/ref=sr_1_5?s=computers&ie=UTF8&qid=1533280749&sr=1-5&keywords=PL2303HX#customerReviews Looks OK ?

Hi, I am using the Bridge Option. My Mac running the Windows VM has the following IP: 192.0.0.129 My Windows VM is 192.0.0.128 (running TFTP) My 2nd Mac has the following IP 192.0.0.130 From the 2nd Mac, I can TFTP to the 192.0.0.128 running on the Windows VM and GET the firmware file (This as...

I have a windows VM running on a Mac Mac and camera are wired to a PoE switch The windows VM is running the TFTP server

So i ve downloaded the Hikvision TFTP Server from dropbox it is fired up and it is initialized on 192.0.0.128 FW is opened as I can connect to the TFTP and type get the divicap.dav file and download the file from another laptop But the camera is not connecting to the TFTP. it is not even trying...

Hi alastairstevenson, Thanks for your answer. SADP (Thanks for the link): it shows firmware 5.5.2_Build171201 that I ve installed on the camera. I get it from DOWNLOAD PORTAL You were right IP Address was 192.168.1.64 and not the one I mentioned when I do a ping of 192.168.1.64 it is reachable...

Up - Please - Anybody could help ?

I did a factory reset, well, I am getting the IP 192.0.0.64 instead of the fixed IP I had configured. But the issue remains the same. the camera is stuck in boot loop so I cannot access to the web UI

Hi All, I have a DF8223I-AEL IP Dome Camera. I wanted to upgrade to the latest firmware IPD_R3_EN_STD_V5.5.2_Build171201 the Release Note shows that it is supported on my camera. It looks like the upgrade failed. And I can hear my camera is in booting loop. I do not have remote access to it...