Search results

I am on 5.7.7.10 now and the issue is fixed. Haven't gotten the update for 5.7.7.11 yet but I would hope it remains fixed in that version.

I did not know that existed, thank you.

That does seem to be it, I didn't have the option for 5.7.7.5 though as I was on 5.7.7.7 so I dropped back to 5.7.6.8 and all is working again.

The last few days all of my alerts have started being cancelled as "occupied". When I review the AI analysis the moving vehicle is identified in the first couple of sample images with a confidence greater then my setting, then after the vehicle leaves the frame the sample images start showing...

Did they fail the same way? Reboot loop?. I just had a fourth camera fail, I was beginning to suspect maybe an issue with the Cisco 3750X powering the cameras, except the fourth camera that failed was at a different site that is using a Juniper EX2200. It's even a different brand of Cat5e...

It's been reset about 5 times. It does have a 12vdc plug, but I don't have any 12v 1a bricks, plenty of 12v 2a but no 1a. I'll have to see if I can find one as you said, that's about the last thing to test, but if that fixes the camera is still not usable for me so it would just be trying to...

Have tested with two different POE switches, with different cable runs at two different sites. The original installation site with a Cisco POE switch, and at my house on my desk with an Ubiquiti POE switch. The Cisco switch at the original installation site is a 48 port 3750X that is currently...

No SD Card in the camera, Chrome/IE/Edge all have the same behavior. This camera was not previously added on my BI server but I input the IP/creds and ran the find/inspect Opening 192.168.1.90 port 80... HTTP Get / request... OK ONVIF GetSystemDateAndTime 2022-02-24T03:44:25.000Z Requesting...

The video preview just stays on this black screen with the spinning circle The log shows this sequence repeating endlessly

I mean no video directly in the WebGUI of the camera, not even attached to BlueIris, so no watch dog restarting the camera either.

Just had a third camera with the same symptoms. Video never loads and the camera reboots every ~80 seconds.

find/inspect appears to run without issue, but still no video in either BI or the cameras WebUI

I have 15 of the Dahua 2431's running in Blue Iris and it's been working great for over a year. This week two of them started showing no signal in the Blue Iris console. I can ping their IP address, and I can access the WebGUI, but the video preview is just a black screen. I've tried rebooting...

I'm not too concerned with plates just an alert of a vehicle/person coming through. I plan to add another camera in a different spot that may be better for capturing plates. I can try changing some things one at a time to see if it improves. Reading the description, it does sound like HLC would...

So is there a Zone crosses config there or just a single zone in use and trigger on any motion in it? I will try unchecking the object travels tonight and see if that makes a difference. The camera is a Dahua 2231, all of the settings are default right now as I didn't configure anything other...

Ironically it triggered going up this time but not until I was almost entirely out of Zone C, and did not trigger on the way back down. Min Object Size: 204 Min Contrast: 18 Object Travels: 100px Feed: 1080p Object Size Exceeds: Unchecked Crosses Zone: B-C Zones in previous post Make time: 0.5...

These are zones B and C and I have the object crosses zones setup as "B-C", I also have zone "F" setup as the entire image so there's no blind spots where motion won't be detected at all based on Youtube guides I always see posted here but don't have zone "F" anywhere on the crosses zones...

I'm getting an alert when coming down the driveway now but not going up. It doesn't detect motion soon enough in the bottom zone before it crosses into the upper zone. I'm getting a lot of false positives from bugs flying around though with the contrast difference all the way down. Is there...

That's what that check box means. I've been trying to figure that out since setting up the zones yesterday. I had an understanding based on the description, but now that you mention the yellow box disappearing and I see it in action it makes sense now. Thank you. Will uncheck it, getting late to...

I'm having some trouble getting motion detection to work with dark vehicles at night. I setup some zones in the middle of the driveway and a trigger when an object crosses between the zones going either up or down the drive. This is working great during the daytime, and has eliminated pretty...

Anybody? I still haven't gotten this working. I have a pending out of warranty support ticket in with Q-See to see if they can provide it but I don't have high hopes for an answer there.

I removed everything and pressed OK so it would save and then opened it back up to do the inspect. Below on the left you can see what the settings were before the inspect and on the right the inspect dialog. The only thing under the "RTSP port detected!" that is partially cut off is "done"...

I tried dropping the :85 and that did not work either. Here is the config.

Hello, I'm trying to add cameras that are connected to a Q-See QS4816 DVR. The mobile app from Q-See for that model has not been updated in years and has not been supported in the last few version of iOS. I am in the process of slowly replacing these cameras with some Dahua IP cams and using...