vto2000a
-
S
Dahua VTO2000A FW4.3 SIP connection problems with VTH1510CH
I have a 2-wire setup (ip-gateway) with 1x VTO (modular) at front door and 3x VTH for each floor. The default factory image was v3.12x (non-SIP) and has been upgraded to v4.3 SIP. The upgrade from 1 of 3 VTH devices failed but could be recovered using TFTP method. Upgrade Steps: - upgraded... -
R
VTO2000A + VTH1560BW - video issues when calling VTO->VTH, opposite direction is ok
Hi all, I have following setup: Outside: VTO2000A - firmware V4.300 (new one with SIP) Inside: VTH1560BW - firmware V4.300 (new one with SIP) Wired with CAT6 and CAT5 cable. After firmware upgrade I performed factory reset on both. Both see each other in terms of configuration, no apparent... -
Cannot make calls between Dahua VTO2000A and two VTH2421FW-P
Hello, Can annyone can give a suggestion what can be wrong with system I'm working with. I'm trying to connect 1VTO-2VTH system. I kind of certain that I made network configurations properely, because live view on VTH and mobile phone is working, it's able to unlock the doors. But i can't make...- rytuliux911
- Thread
- dahua vth vto2000a
- Replies: 2
- Forum: Doorbells
-
D
Dahua VTO2000a with wrong MCU firmware
While I was updating the firmware for the VTO2000& and VTH1550CH to the 4.3 SIP firmware, I also did the MCU updates. All went fine except a stupid mistake from my side: per accident I selected the VTH MCU firmware and installed it on the VTO via the VDP config tool :( That update said...- Droefelken
- Thread
- dahua firmware mcu vto2000a
- Replies: 48
- Forum: Dahua
-
E
Feed KNX sensor data into VTH1660CH for alarm functionality
Hi, a while ago I started to use my VTH1660CH / VTO2000A as a alarm system. For this I need to provide the available sensor data of my KNX system to the VTH1660CH and/or VTO2000A. Because - both system shall be galvanic separated (failure in one system shall not damage the other, grounding not... -
Dahua VTO2000A doesn't work (light starts blinking, it disappeared from the network).
Hello, ipcamtalk members, this is the first time that I'm posting here. I have a Dahua VTO2000A outdoor station connected to Dahua VTH1550CH indoor monitor the VTO was working well I can view the outdoor camera from the monitor and the phone but just a 10 - 15min after, the VTO namespace light...- Eraking
- Thread
- dahua dahua camera dahua vto2000a doesn't work ip indoor monitor security camera survaillance camera villa outdoor station vth vto vto2000a
- Replies: 8
- Forum: Home Automation
-
gDMSS/iDMSS unlock VTO2000A Door from any Dahua Network Camera View
Hi beloved folks. I have configured a project on a Villa with the Villa Outdoor Station module (VTO2000A) to open/close the garage & pedestrian door from the guardhouse from a IP Indoor Monitor (DH-VTH1560B), in between of course i have the PoE Switch (VTNS1060A), and for opening both doors i'm...- jurgenmeister
- Thread
- door station gdmss idmss network camera vto2000a
- Replies: 0
- Forum: Dahua
-
B
Vto2000A: stuck with old firmware
Hi everybody I'm using my vto with sip firmware in conjunction with my virtual asterisk pbx (same location but different network/vlan). At the beginning i successfully upload the sip firmware "General_VTO2000A_Eng_P_16M_SIP_V1.200.1000.0.R.20160505" via configtool 3.2.0 and after a year this... -
S
best IP camera ? + doorstation setup
Hello IP camera experts I have been browsing the World Wide Web for a few days now to find the correct setup regarding IP camera surveillance. I'm a bit of a perfectionist and always try to find the right solution for an acceptable price. My basic setup consists of parts from the Dahua brand 2... -
Y
Dahua video IP intercom kit with Synology Surveillance station horrible sound
Hi all, When i configure my kit, almost default except network, admin password and language all is working fine. However, when configuring Surveillance station (Synology 413j) to connect to my VTO2000A as a security cam. which is also working great, when i answer a door call it's not possible...