Acusense and basic motion detection
- Thread starter surfboomerang
- Start date
@surfboomerang
what you see in the Synology SS is expected. This is due to the limitation on the Synology side where they cannot filter Hikvision Acusense events for the basic motion detection. See post below. Synology need to update their logic to support that.
Hikvision Acusense supported for basic motion events in Surveillance Station 9 | Synology Community
what you see in the Synology SS is expected. This is due to the limitation on the Synology side where they cannot filter Hikvision Acusense events for the basic motion detection. See post below. Synology need to update their logic to support that.
Hikvision Acusense supported for basic motion events in Surveillance Station 9 | Synology Community
i use continuous recording to the NVR as well as the SD card. SD card is just a back up if for whatever reason my NVR went down. However I went in and set up one camera as you have. Just motion detection with vehicles and humans checked and armed to only trigger a recording if the event occurred. And then to allow some time to pass to capture footage, I decided to do the overdue dreaded windows update and have been patiently waiting for it to finish to check out the results lol. I will update you once I can see what it did!
Alrighty friend. I set one camera as you have. Motion enabled with human and people set to record only on event. I actually got nothing at all.
But then I changed to record motion and that did the trick!
So set up your motion, arm continuous, make sure to click trigger recording and upload to memory card. Then under recording set it to motion, not event.
I only have clips of actual people or vehicles on the sd card so should work for you.
@Vandoe
I tested the exact same configuration as you (tthe only thing I had to change was the recording schedule from event to motion) and the camera still records on any motion, not just vehicles and humans. Recording still gets triggered on leaves blowing around, my hand waving in front of the camera, trees swaying. etc. So, clearly and sadly this is a bug in the 2387's firmware
.
Thanks a lot for testing that out. I'll have to plan on sending the camera back if the seller can't get the issue resolved with Hikvision.
I tested the exact same configuration as you (tthe only thing I had to change was the recording schedule from event to motion) and the camera still records on any motion, not just vehicles and humans. Recording still gets triggered on leaves blowing around, my hand waving in front of the camera, trees swaying. etc. So, clearly and sadly this is a bug in the 2387's firmware
.Thanks a lot for testing that out. I'll have to plan on sending the camera back if the seller can't get the issue resolved with Hikvision.
Last edited:
@Vandoe
I tested the exact same configuration as you (tthe only thing I had to change was the recording schedule from event to motion) and the camera still records on any motion, not just vehicles and humans. Recording still gets triggered on leaves blowing around, my hand waving in front of the camera, trees swaying. etc. So, clearly and sadly this is a bug in the 2387's firmware
Thanks a lot for testing that out. I'll have to plan on sending the camera back if the seller can't get the issue resolved with Hikvision.
And this is when you are playing back via web browser on the actual camera?
Wow yea that is very weird. I’ll check what firmware version I’m on when I get home. Hopefully they can fix it for you. It should work since it’s an acusense camera even without an NVR.
Why don’t you try taking record off of any schedule. And then in motion detection just keep the alarm continuous, and checking upload to sd card, notify surveillance center and trigger recording. Since the alarm seems to be acting correctly.
If you disable the schedule, it will disable video recording completely. The schedule is necessary as all recording is based on the schedule no matter what. The linkage method ties to the schedule in order to record. If you disable the schedule, there will be no video recording.
The "Upload to FTP/Memory Card/NAS " option is only for a single snapshot image storage. This does not record video. The very last post here also explains that:
www.use-ip.co.uk
The "Upload to FTP/Memory Card/NAS " option is only for a single snapshot image storage. This does not record video. The very last post here also explains that:
Event Storage on SD Card / NAS - I can't see any VCA events?
Hi all, I have a couple of DS-2CD2385G1 cameras, both of which write their video footage to my NAS (I have no NVR). I have configured both cams to record continuously and also record line crossing events (so I thought!). The issue is that when I connect to these cameras using iVMS-4200, I can...
www.use-ip.co.uk
If you disable the schedule, it will disable video recording completely. The schedule is necessary as all recording is based on the schedule no matter what. The linkage method ties to the schedule in order to record. If you disable the schedule, there will be no video recording.
The "Upload to FTP/Memory Card/NAS " option is only for a single snapshot image storage. This does not record video. The very last post here also explains that:
Event Storage on SD Card / NAS - I can't see any VCA events?
Hi all, I have a couple of DS-2CD2385G1 cameras, both of which write their video footage to my NAS (I have no NVR). I have configured both cams to record continuously and also record line crossing events (so I thought!). The issue is that when I connect to these cameras using iVMS-4200, I can...
Yea makes sense. Was just trying to think of anything else to play around with. Glad to have an NVR to do all this for me regardless lol
I am having the same issue with my 2387G2. Firmware 5.7.10 build 220720. Using BI, not an NVR. Would like the SD card in the camera to only record human and vehicle.
Under Basic Event, motion I have "Target Detection" human and vehicle options checked. The camera records all motion to the SD card, not just human and vehicle.
Under Basic Event, motion I have "Target Detection" human and vehicle options checked. The camera records all motion to the SD card, not just human and vehicle.
Under your record schedule is it set to event or motion? If event, switch it to motion. If it still doesn’t work you must have same issue as OP.
