Hikvision nvr dont work with cisco ip camera

[Enptyboss]

I have hikvision nvr model : ds-7104ni-q1/m
Trying to set it up with cisco 6930 via onvif but no results. It is saying “incorrect login or password”
Onvif is enabled, full access from onvif device manager. But still cant get it working on nvr

 

[tangent]

try setting the camera to the same password as the NVR

 

[Enptyboss]

try setting the camera to the same password as the NVR

It actually is setted up to same password, lol

 

[Enptyboss]

I also tried admin/admin for login and pswd in nvr and still no results

 

[alastairstevenson]

Trying to set it up with cisco 6930 via onvif but no results. It is saying “incorrect login or password”

Have you specified the 'ONVIF port' as shown in ONVIF Device Manager? Sometimes it's not 80.
Have you tried if it will connect via RTSP using a Custom protocol, using the RTSP string from ONVIF Device Manager?

 

[Enptyboss]

Have you specified the 'ONVIF port' as shown in ONVIF Device Manager? Sometimes it's not 80.
Have you tried if it will connect via RTSP using a Custom protocol, using the RTSP string from ONVIF Device Manager?

I try to access network parameters from onvif device manager and it says that ntp is not supported by server

 

[alastairstevenson]

Have you specified the 'ONVIF port' as shown in ONVIF Device Manager? Sometimes it's not 80.

The 'ONVIF port' can be seen in the URI at the bottom of the Identification panel.

Have you tried if it will connect via RTSP using a Custom protocol, using the RTSP string from ONVIF Device Manager?

The RTSP string can be seen at the bottom of the Live Video panel.

 

[Enptyboss]

The 'ONVIF port' can be seen in the URI at the bottom of the Identification panel.


The RTSP string can be seen at the bottom of the Live Video panel.

Its 554, i tried to connect it with custom (1-4) and it says that “no video link”

 

[alastairstevenson]

Its 554, i tried to connect it with custom (1-4) and it says that “no video link”

554 will be the RTSP port, not the 'ONVIF port'.

 

[Enptyboss]

554 will be the RTSP port, not the 'ONVIF port'.

My bad,
Well onvif version is 2.0
And there is uri

http://192.168.1.180/onvif/device_service

 

[Enptyboss]

554 will be the RTSP port, not the 'ONVIF port'.

So its probably 80 because nvr detects 80 port no matter what and also it is not shown in uri

 

[looktall]

“incorrect login or password”

Well the obvious answer is that you're using the wrong credentials to connect.
Does the camera have its own web confirmation page that you can access and confirm what credentials are used for onvif?
Did you create an account specifically for onvif?

 

[looktall]

The manual says this about rtsp.
Bold added by me.

Transmission Control Protocol (TCP) port on which the IP camera receives
Real-Time Streaming Protocol (RTSP) commands. You must configure this
port if you want to allow third-party devices or software to access video
streams from the IP camera.
RTSP is a standard for connecting a client to control streaming data over the
web.
Valid values are 554 and 1024 through 65535. The default port is 554.

It says this about onvif.
Again bold added by me.

Click Save to be redirected to the login page. After login, ONVIF service
starts working.

 

[alastairstevenson]

also it is not shown in uri

Yes, that's correct, if the ONVIF port is 80, it's not shown in the URI.