IPC-HDBW4231F-E2-M

EMPIRETECANDY

IPCT Vendor
Joined
Nov 8, 2016
Messages
3,498
Reaction score
6,971
Location
HONGKONG
Here is the latest new firmware for these cams.
Dahua not mention too much about the updating.
PAL NTSC for downloading

IPC-HUM8231-E2,
IPC-HDBW4231F-E2-M
IPC-MW4231A-E2

Attention, this is for the multi-lens camera updating, please be carefully before you make updating.

Andy
 

Attachments

Last edited:

YYZed

Getting the hang of it
Joined
Jul 3, 2019
Messages
98
Reaction score
80
Location
Watching over you from everywhere
Last edited:

looney2ns

IPCT Contributor
Joined
Sep 25, 2016
Messages
8,986
Reaction score
7,751
Location
Evansville, In. USA
Updated without issue.
IVS now available on both channels.
Select at the Smart Plan tab, and in IVS setup.
Backlight is missing on Ch2, thus WDR on channel 2 has disappeared, not had time as yet to see if WDR on ch 1 affects ch 2. This is a bummer either way.
 
Last edited:

EMPIRETECANDY

IPCT Vendor
Joined
Nov 8, 2016
Messages
3,498
Reaction score
6,971
Location
HONGKONG
Updated without issue.
IVS now available on both channels.
Select at the Smart Plan tab, and in IVS setup.
Backlight is missing on Ch2, thus WDR on channel 2 has disappeared, not had time as yet to see if WDR on ch 1 affects ch 2. This is a bummer either way.
That is great news!
 
Joined
Jul 29, 2019
Messages
10
Reaction score
4
Location
Universe
Updated without issue.
IVS now available on both channels.
Select at the Smart Plan tab, and in IVS setup.
Backlight is missing on Ch2, thus WDR on channel 2 has disappeared, not had time as yet to see if WDR on ch 1 affects ch 2. This is a bummer either way.
IVS can only be active for ch 1 or ch 2, but not both simultaneously. On the Smart Plan page there are radio buttons, not check marks.

BL settings seems to affect both channels.
 

flynreelow

Pulling my weight
Joined
Dec 12, 2016
Messages
412
Reaction score
159
Updated without issue.
IVS now available on both channels.
Select at the Smart Plan tab, and in IVS setup.
Backlight is missing on Ch2, thus WDR on channel 2 has disappeared, not had time as yet to see if WDR on ch 1 affects ch 2. This is a bummer either way.
Did you check IVS for both cameras, at the same time?
 

Martin M

n3wb
Joined
Sep 11, 2019
Messages
4
Reaction score
4
Location
Estonia
Updated without issue.
IVS now available on both channels.
Select at the Smart Plan tab, and in IVS setup.
Backlight is missing on Ch2, thus WDR on channel 2 has disappeared, not had time as yet to see if WDR on ch 1 affects ch 2. This is a bummer either way.
Where is the IVS setup you mentioned?? Tried both NTSC and PAL same..
 

Attachments

Martin M

n3wb
Joined
Sep 11, 2019
Messages
4
Reaction score
4
Location
Estonia
After further checking, it can be enabled on second ch, but appears to only "work" with one channel at a time.
yep thats the problem :) I changed in html console radio buttons to "checkbox" and then I get IVS lines for a moment on both channel, but if I refresh page they are gone and reverts to original setting I have. Appears that there is more than Radio/checkbox issue.
 

Attachments

Martin M

n3wb
Joined
Sep 11, 2019
Messages
4
Reaction score
4
Location
Estonia
Looks quiet. I have setteled with one IVS. One more problem though, when clamera is set to auto reset every week. Then after reset there is a change that IR leds will go back to SmartIR even though I have them turned off. Didnt happen one week happend next etc. And of course since they are inside dome they are rubbish. Solved by switching off "auto maintenance" reset.
 
  • Like
Reactions: ZrC

dimammx

n3wb
Joined
Apr 9, 2015
Messages
20
Reaction score
12
Hi Andy not sure if this is the best place to ask but is it possible to change camera model number in firmware?
Digital watchdog sees model as IPC-HDBW4231FP-E2-M and requires 2 licenses to use. If camera name is IPC-HDBW4231FN-E2-M only 1 license should be required.
 

Sybertiger

Getting comfortable
Joined
Jun 30, 2018
Messages
902
Reaction score
932
Location
Orlando
Any further update?
I bought one of these from Andy during his BlackFriday/CyberMonday sale late November and received it a few weeks ago. It has version 2.622.0000000.32.R, Build Date: 2019-08-27 on it and would assume it's the latest. The box it came in had a date code of October 2019. It doesn't matter if you load PAL or NTSC version of the firmware if you are using Blue Iris?
 

flynreelow

Pulling my weight
Joined
Dec 12, 2016
Messages
412
Reaction score
159
I bought one of these from Andy during his BlackFriday/CyberMonday sale late November and received it a few weeks ago. It has version 2.622.0000000.32.R, Build Date: 2019-08-27 on it and would assume it's the latest. The box it came in had a date code of October 2019. It doesn't matter if you load PAL or NTSC version of the firmware if you are using Blue Iris?
for ip cameras, pal vs ntsc doesnt matter. but if you are in the states, just load the ntsc firmware
 
Top