Question about IPC-B52IR-X3 3x 2MP Perimeter Camera

[Simas123456]

IPC-B52IR-X3 3x 2MP Perimeter Camera.
3.142.0000000.1.R
Build Date 2024-08-01

I'm trying to understand some of the software options.

1) Alarm>Exception>Voltage Detection>Abnormal Voltage. Is the camera monitoring input voltage, such as 12v or POE+, or is it monitoring output voltage to the "DC 12V OUT"?
2) System>Peripheral>Serial Port. This does NOT have a selection for a PTZ protocol. How is it used? It appears that the PTZ control is used to tilt the three lenses up and down, but what is the serial port for? Is it to feed RS-485 into the camera to tilt the lenses (which would require a protocol like PELCOD), or is it an output to other devices?
3) System>Peripheral>External Light. How do I use this, and is it fed from 12V DC OUT or through RS-485?
4) System>Peripheral>Wiper. How do I use this, and is it fed from 12V DC OUT or through RS-485? This camera has no wiper and does not seem to have a place to mount one. Perhaps it is a vestigial piece of the software? Can it be used to trigger something?

 

[bigredfish]

My understanding

1- Monitoring camera input
2- no idea
3- I found that to activate the onboard IR or white LED, deceiving label
4- Not certain I think leftover from FW for PTZs.

 

[mat200]

IPC-B52IR-X3 3x 2MP Perimeter Camera.
3.142.0000000.1.R
Build Date 2024-08-01

I'm trying to understand some of the software options.

1) Alarm>Exception>Voltage Detection>Abnormal Voltage. Is the camera monitoring input voltage, such as 12v or POE+, or is it monitoring output voltage to the "DC 12V OUT"?
2) System>Peripheral>Serial Port. This does NOT have a selection for a PTZ protocol. How is it used? It appears that the PTZ control is used to tilt the three lenses up and down, but what is the serial port for? Is it to feed RS-485 into the camera to tilt the lenses (which would require a protocol like PELCOD), or is it an output to other devices?
3) System>Peripheral>External Light. How do I use this, and is it fed from 12V DC OUT or through RS-485?
4) System>Peripheral>Wiper. How do I use this, and is it fed from 12V DC OUT or through RS-485? This camera has no wiper and does not seem to have a place to mount one. Perhaps it is a vestigial piece of the software? Can it be used to trigger something?

looks really good for parking lots and the like ..





3 × 2 MP Triple-Sight Perimeter Protection Bullet Network Camera


3 × 2MP 1/2.8" CMOS image sensor, low luminance, and high definition image.
Outputs max. 2 MP (1920 × 1080)@25 fps through channel1-3.
H.265 codec, high compression rate, ultra-low bit rate.
Built-in 8 IR LEDs, and the max. illumination distance is up to 100 m.
Supports long-range perimeter protection. The camera can detect humans and vehicles up to 100 m away and more.
WDR, 3D NR, HLC, BLC, digital watermarking, applicable to various monitoring scenes.
With deep learning algorithm, it supports Perimeter Protection, including Intrusion and tripwire (the two functions support the classification and accurate detection of vehicle and human).
Abnormality detection: Motion detection, video tampering, scene changing, audio detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, and voltage detection.
Alarm: 2 in, 2 out; audio: 1 in, 1 out; supports max. 1TB Micro SD card; built-in dual Mic and speaker, supports two-way talk.
ePoE.
IP67 and IK10 protection.