Recent content by Daijoubu

  1. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    Do you have a picture of the other side of the PCB?
  2. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    Is the replacement battery charged? Voltage on the pins? Unless the BMS on it needs to be waken up
  3. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    These 2 pins that makes contact with the brass contacts on the rear housing, one of mine was broken (DB1C but similar internal connection), check for loose connectors and cables too
  4. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    I'm talking about the doorbell itself, the PCB sandwich gets power from some gold spring contacts, check that they are not damaged
  5. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    I would check the POGO/sping contacts pins, they are very thin, almost fuse like, mine burnt when I tried to feed the doorbell DC power when it rang the bell but never released it (probably looking for a zero cross), had to fix it with some solid copper folder iirc
  6. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    I do have a separate PoE camera with a larger IMX347 1/1.8" sensor as well, running PoE to my doorbell is a nono lol. The Reolink Doorbell quality is fine if you have sufficient lights but still has it's limitation due to its form factor
  7. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    I did this a couple of times then got tired of formatting it (Sandisk High Endurance card), replaced it with a Samsung Pro Endurance and no more errors. The old card did test fine and I'm using it in my Switch to store games (write once/read many), card could be on its way out and errorring
  8. Daijoubu

    New RCA HSDB2A 3MP Doorbell IP Camera

    Maybe the internal lipo battery is dead, mine is puffy, gonna order a replacement myself. Part no LF602025-2 220mAh, 3.7V
  9. Daijoubu

    I finally figured out the 8MP 1/1.2" and 4MP 1/1.8" CMOS models Hikvision uses

    Still good sensor for the money, no? MC-J40 is just a bit more $ also
  10. Daijoubu

    I finally figured out the 8MP 1/1.2" and 4MP 1/1.8" CMOS models Hikvision uses

    Hah is that the sensor in the Anjvision MC-J30 module? Supposedly SC450AI as per taobao sellers but it's not, in the firmware it's called SP4329, after googling, I think SP may refer to SuperPix that is now part of Omnivision? Looks pretty similar to the HK187 sensor, the little dots (wire...
  11. Daijoubu

    [Review] Anjvision IMX347 4MP 1/1.8" Starlight Camera Module MC-K45

    Is H.265+ compatible with a Synology NAS? My modules came with latest firmware version 3.2.2.2 maybe I can try to downgrade to previous one.
  12. Daijoubu

    [Review] Anjvision IMX347 4MP 1/1.8" Starlight Camera Module MC-K45

    So I got 2 other MC-K45 modules, they all have H.265 encoding problems, what settings are you using? H.264 seems fine I have it set to 2688x1520 CBR 6Mbps 30 fps with iframe every 30 frames. Tried lower fps and higher iframe interval, VBR but it will always glitch up
  13. Daijoubu

    [Review] Anjvision IMX347 4MP 1/1.8" Starlight Camera Module MC-K45

    Ok so I reapplied some thermal tape but it didnt fix the issue but I'm not sure if it's my sample, I will retest when I get my 2 other modules that I've ordered. I was able to narrow down the conditions when these compression artifacts occurs in the main stream, if happens when the sub stream...
  14. Daijoubu

    [Review] Anjvision IMX347 4MP 1/1.8" Starlight Camera Module MC-K45

    One more thing, is this module capabable of switching between day and night mode without a CDS? I tried to set the min shutter speed for night mode but it seems to be always in daytime mode from my test
  15. Daijoubu

    Reolink CX410

    Btw this CX410 uses the same sensor as the Dahua 54xx series, Omnivision OS04A10, so bad SoC/ISP/processing?
See more
Top Bottom