Recent content by Edlee

DS-7616NI-E2 / 16P V3.4.103 DS-2CD2342WD-I V5.5.82 Whenever i turn on H.264+ on these ip cams, it takes much longer to load the high resolution image, like 5-8 seconds, instead of split second on regular H.264 mode, i have the latest firmware and i can not figure out the issue, i tried lowering...

mostly the issue is with H.265 + being enabled, i noticed when i disabled the plus, its back to being clear

I recommend everyone to avoid V5.5.0, there is noticeable blurring , i updated a few of my DS-2CD2342WD-I, and they look terrible, i am not talking about 5% less quality, its obviously something is going on

IPC_R6_ML_STD_5.5.0_170725.zip when i used the hiktools to read the language version it shows something i have never seen before it says: iLanguage: 0x01E9E9BE [32106942] even after i tried changing language, it now shows: iLanguage: 0x01E9E901 [32106753] EN/ML I am afraid to use this file and...

i know it works, the only time i see the problem is when the ir cut is on for long period of time, like 48 hour weekend, and then on monday morning, it does not turn off.

Thank you, I wish i knew about that Virtual Host feature before I upgraded all the ipcams individually on another poe switch. I will check out that Day/Night setting next time the problem occurs, and see if I can change manually

How do I access the camera GUI though the NVR with built in POE that they are plugged into? I just finished upgrading the NVR to V3.4.21 build 160630, and the cams to V5.4.0 build 160530 I know its a shot in the dark, i am hoping it will alleviate the IR cut problems

I have a USA Retail Version of the DS-2CD2332-I, after about a week of being on, it does not come out of IR Cut mode (night Mode). I tried flashing a strong light onto it, and lightly knocking on it, and it does not help. The only way is unplugging it from the Hikvision NVR which has a built...

I have a usa retail box version, i have 11 cams, i am recently having an issue with one that did not come out of ir night mode, had to unplug the camera from poe switch to get it to work. For some reason it happens once every few months.

Is there a download link for USA 5.4.0 firmware for DS-2CD2332-I?

I received codes from hikvision and my distrubuter, and both "reset password failed" through sadp, i have no clue what to do now, cause the device does not even take tftp the hikvision cs only replied "Dear customer, The password reset system may not 100% accurate." There must have been a...

Yes I tried that, and i have restarted the nvr 100 times trying to get it to take the file from the hikvision tftp, and it does not work. Its strange that I was able to get it to activate previously when trying to unsuccessfully do tftp I am giving up now, and just email my ebay rep the...

Thank you, for some reason i could not get tftp to connect, kept getting failure, even after rebooting 10 times, then all of a sudden i get the activation screen through hdmi, and it gave me an option to set new password. Not sure how i got that to work. Now im in the process of reloading...

no i dont have the saved configuration file, do you think I should tftp recovery upgrade to the 3.4.0 firmware that is on the european hikvision site, and hope my old password will work again?

Thank you for the info, I tried different browser from different pcs, and i tried using SADP, and i do not get any activate screen and i tried both passwords you mentioned 12345 and 123456789abc with no luck. I attached the output from SADP 3.0, but I have been trying to get this reset using...