Search results

  1. Rick Rick

    Remote Access Test Fails

    Actually it is the XB6 and is a combo
  2. Rick Rick

    Remote Access Test Fails

    As far as I can tell it is the the xFi and is a combo.
  3. Rick Rick

    Remote Access Test Fails

    I recently changed my comcast modem. I have my own Netgear router and wireless. After changing the modem I found that I can no longer reach my BI from the public address. I run the WIzard and ift fails the Remote Access test with "The operation has timed out". I run canyouseeme and it fails with...
  4. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Yeah, you were right about that. I had lots of problems. THey sent a replacement and still problems. I returned the replacement and kept one that I bought for 1/2 price. I bought a Dahua like you recommended and it works fine.
  5. Rick Rick

    Blue Iris New Version Does Not Have Framerate Limiting Control-Major Issue w Foscams

    Thanks. I tried it and BI can not log in on another setting. I am sending the camera back. IT was a FI9821. So warning to anyone who may buy it :-)
  6. Rick Rick

    Blue Iris New Version Does Not Have Framerate Limiting Control-Major Issue w Foscams

    I have a problem with BI causing a change in my Foscam Video settings. WHen BI starts up or I make a change to the settings in the BI for the camera it cause a change in my camera settings. I set the camera to stream a Frame rate of 10 then start BI which causes the camera to reset it to 25...
  7. Rick Rick

    BI causes slow response or disconnection of wireless cams

    Yeah I had already done that before I posted the thread. But your post made me think about it again. I realized that I had rebooted the router but I forgot that I had an extender. So this morning I tried rebooting the extender and all the cameras using the wireless on that extender. It seems...
  8. Rick Rick

    BI causes slow response or disconnection of wireless cams

    Don't know what reasons you are referring to. Bottom like BI is doing something that affects the network a lot or specifically the wireless. Can't figure what that could be. Anyone have an idea? I can run all cams in browsers with no problem. Something specific to running BI.
  9. Rick Rick

    BI causes slow response or disconnection of wireless cams

    Yeah it could be something with my network, but it only happens if I start BI. I can repeat this over and over again.
  10. Rick Rick

    BI causes slow response or disconnection of wireless cams

    Recently BI has started causing my wireless cameras to be very slow in response or disconnect. I have reproduced this many times. I can bring all my wireless cams up in browsers and no problem. I start BI and try and access them and they get unresponsive. I have 3 wireless cams and 7 wired. My...
  11. Rick Rick

    Anyone know about CCTV-Mall to purchase camera?

    I found a really low price on a camera there but was wondering if this vendor is any good?
  12. Rick Rick

    Does anyone know about the following cameras? Qulaity, Reliablilty?

    Thanks
  13. Rick Rick

    Does anyone know about the following cameras? Qulaity, Reliablilty?

    Recommendations?
  14. Rick Rick

    Does anyone know about the following cameras? Qulaity, Reliablilty?

    1. LEFTEK Mini Outdoor IP HD 4.0 Megapixel model SCNEW-14966 2. Inesun PTZ IP INS-HD54F-5.0MP-18X 3. Kenuco Mini High Speed IP 1080p 2MP PTZ model IP12
  15. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    This thread is getting off the subject somewhat. Does anyone have any suggestions/experience at reducing pre-trigger time that has not been mentioned here?
  16. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Yes. And there some areas that I can not use motion detection based on the time of day.
  17. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    I scheduled the camera to monitor different areas depending on what time of day it is.
  18. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Good point. THat is why I have already suggested to BI folks that they should allow the ability for a camera to know which other camera triggered the group
  19. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Yes I use PTZ all the time. THat way I dont have to have a lot of cameras put on the front of my house.
  20. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    No other zones set
  21. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    I mean PTZ
  22. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    I do use PTX alot. Any thoughts on the LTS PTZIP212X20?
  23. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    I have sent you everything under the "Trigger" tab. What else should I send you?
  24. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Hmmmm well wish I had talked with you before buying. Can you recommend a comparable camera? I have a WHat do you recommend to purchase?. I have a Sunba 405-D20Xd
  25. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    I don't know where to find the settings you request.
  26. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    THanks for the info. Yes I have had trouble with night vision and they are sending me a replacement. But it may not fix this. I may have to return
  27. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    You say " you must match the BI settings for I frame interval to the FPS". How do I do that if the FPS settings in BI "mean nothing" and the "I frame interval settings are set in the camera". What do I set in BI to match the camera?
  28. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    OK. But can you be more specific? What can it not do that other cameras can do?
  29. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Can you tell me what are the problems with Sunba?
  30. Rick Rick

    Pre-trigger needs to be set to 10 sec to get triggered recording

    Below us what the camera is set at. Again my question is :SInce FPS settings "does nothing in BI" (per previous post) and you can not set IPS settings in BI what should you set to accommodate the transfer rate of the camera?
Top Bottom