Search results

Yet again, thanks for your help. You were right with the assumption that the issue was with the NVR. I thought that I had cleared the camera from being added to the "group" within the remote NVR's settings. But as it was still present it was hammering the same IP address and attempting to...

I had hoped that this tool might help me with my DS 2CD2032-I and 5.25 firmware. I did have access but then didn't change my NVR to use the correct password when trying to add its stream to view. So it became "locked" for twenty minutes, which never seems to end. I used the tool and .... it...

WORKING...... Not sure what I did different but yet another reset and up it pops within the SADP tool... IP 192.168.0.64 It has firmware revision of V5.2.5 build 14120 and as it is working it will be used tomorrow so that I can remove another Hikvision camera for a potential firmware upgrade...

Hi I have a spare camera that I have been trying to bring back into service. It is a DS 2CD2032-I type. It worked previously when I boxed it away for a few years, in the original packaging. On getting it out I powered it up with a 12v supply and connected it to a my LAN via a cable to a switch...

Yup that point alone, in bold, suggests that it isn't the best of ideas. Then again I can remotely access the POE switch and temporarily cut power to all but the camera I would be needing to work on. Thanks for the point regarding best working with the camera via a switch connection and an...

Thanks for your reply and advice. Also big help with the correct firmware to apply, that could have been messy. Thanks also for the warning of the potential risk, at least I'll have choice and options if I decide to try and resolve it by flashing. A pity that a weekly reboot couldn't be applied...

Thanks for creating these utilities, perhaps they could be useful for me.... Amongst my Hikvision CCTV cameras I bought one of these several years ago.... DS-2CD2232-I520150128CCCH50190XXXX ...a bullet type camera which goes with my other domes. Looking at the serial number via SADP it seems...

I have found that mailing Hikvision regarding technical support has not been too bad. When asking them questions regarding their Windows client software and NVR recording settings they did at first want me to detail precisely where I bought the kit from. I had been purposely vague and so then...

Hopefully it is sorted. Hadn't taken into consideration to other view possible with the NVR.

Hi I have six Hikvision cameras. Five DS-2CD2332-I type and one DS-2CD2032-I. All of them have version 5.2.5 firmware. My NVR is a Hikvision DS-7608NI-SE/P 4 (firmware 3.10 - latest) and each cam is connected to a Netgear POE Switch. The above run well except.... This bit is driving me...

^^^^ That seemed to be the consensus of opinions in some of the posts at the time people were evaluating those features. Whilst it is nice for those people who need them it is pointless, and potentially concerning, if you are relying on features for your security which can be inconsistent at best.

It is going back a little while now but I remember that firmware and the one following, in terms of removed features. IIRC there were indeed many more features in the firmware BUT for many people they simply did not work and if they did then they didn't work reliably. I can't remember all the...

Post #23.... http://www.ipcamtalk.com/hikvision/1784-hikvision-2532f-getting-audio-2.html#post20608

I didn't go into too much detail but basically if I have set each of my cameras for motion detection recording I find that the odd motion recording is either missed our clipped. Settings make no difference to that. So I maintain the triggers for such an event but also now consider full 24/7...

I did note that I was on the latest firmware for each device, 2.3.9 for the NVR and then 5.2.0 for the cameras. But my points were not, necessarily, related to tha tof the firmware but the overlapping inconsistencies between the interfaces of their devices. I had hoped that by sticking to one...

Good point :) As I have hardly used the NVR interface I would not have known that. I do agree with you that the interface and general functionality of each of the types of client are not harmonised between the applications. I would have expected the iVMS-4200 Client to have had the same level...

I haven't has my six Hikvision IP cameras or my Hikvision 7608 NVR for that long nut I was also wondering if the NVR will override those settings of the camera, for motion detection, or, if the camera settings are considered to be more sensitive for triggering an event, and thus supplement those...

Has anyone else noticed when using the above firmware that it no longer seems to be possible just to select a motion schedule for the recording without it being combined with the alarm...? You can now either select a normal schedule or a Motion / Alarm.... ....I used to have mine so that...

I too shared a similar experience but only because CBX wove his skills and magic and thus my cameras are now updated using his excellent utility. Many thanks