Hello ,
I would like to access the events of access control like card swiping , fingerprint , image detection
But I can't find such valuable info
I found some api but it doesn't explicitly specify the action that you can listen for events
Any info or do i need to contact dahua to get full apis...
Morning All –
Background
I’m moving back to my home and wanted to take advantage to start with securing my home network. Gear is 7 POE IP cameras run with Blue Iris, Wifi/ZWave Locks/Doorbells, Always on PCs AND I’m adding Home Assistant (most likely with w Raspberry Pi5) . In past I didn’t...
Few questions over Dahua TIOC Advanced 2.0 DH-IPC-HDW3549HP-AS-PV-0280B-S3 Dahua 5MP AI Active Deterrence Full color Starlight IP Turret Camera. Can all of the functions be used over just POE, so alarm, lights, 2 way voice, AI wizsense.
Hoping to use Home Assistant running frigate NVR + a 24/7...
New to IPsec cam setups, setting up my own home IPcam network with my home assistant w/ Frigate & Coral and wanted to ask the people who know more on this the following:
What IPcameras have we all used with open source firmware that have overall good day/night performance.
Just trying to get...
I wanted to share this and see if anyone is using Home Assistant's Voice Assistant (Assist). I do not have Nabu Casa so I am hoping I can use my VPN tunnel through the Home Assistant Home App that I presently have setup and using. Also don't have ESPHome installed, not sure if I need it...
So I have a unique problem and some inability to frame the issue properly.
I want a camera that records continuous video of to a local storage (specifically a microsd), with playback that can be viewed on Home Assistant.
Requirements:
Camera keeps recording to local storage even with no...
Hello, thanks to everyone for being my go to source for info. This board has helped make me quite the amateur professional when it comes to networking.
My question is about Ring. There service sucks, however I have a property with 4 wired ring flood lights cams, 3 motion activated lighting...
Apologies if this has been covered before - I did scan other DahuaVTO2MQTT posts...
We have Kwikset 916 Z-wave deadbolt locks that are managed by Home Assistant. We also have a Dahua VTO2311R-WP doorbell and three VTH2621GW-WP monitors.
There are numerous times when a friend rings the front...
Is there any way that Blue Iris can trigger a Home Assistant automation when it detects that no signal is being received from a camera? I have most of my cameras plugged into smart sockets, and would like to perform a power cycle whenever any of them goes offline.
I'm running Blue Iris v5 and...
I've recently got addicted on home assistant and want to get the rtsp stream into home assistant so I can send image notifications. I have 4 cameras and 3 I can view the RTSP stream in VLC. One camera I cannot view the RTSP stream as vlc times out. I have my router set up so I can access the...
I'm running home assistant and initially I was using mqtt to trigger in home assistant the motion detector for the camera and then an automation to take a snapshot of the camera as I pulled all the cameras from blue Iris into home assistant.
The issue is there is a significant delay and the...
I have BI recording some Wansview Q6 WiFi cameras and an Amcrest AD110 via RTSP. I also have RTSP feeds for those cameras integrated into my Home Assistant dashboard (snapshots refresh every few seconds, per the HA default). My Wansview cameras seem to reset quite often, and I wonder whether...
Just thought I'd share a little accomplishment I achieved with BI and Home Assistant! I recently put a small propane heater in my shed to keep it warm when working out there and to hopefully keep liquids stored out there from freezing. All assuming I don't burn through my 100lb tank too fast...
Hi All
I have BI5 running, with Sentry AI as well. So far, so good.
It's integrated with Home Assistant as well, and it works for the most part. (motion detection not showing in HA)
I have a problem with BI switching profile from "Away/Ude" (2) back to "Home/Hjemme" (1) without me knowing why...
I actually do try to learn by myself (through trial & error). But this has me stumped.
I have an Ubiquiti UDM router. Let's say I created 2 VLAN subnets: 192.168.1.x and 192.168.4.x
I must have "new" bullet turn on, along with "established" and "related" in my firewall rule.
When I set the...
Hi
I am looking at setting up an NVR and motion captured recordings for 2-3 x POE cameras.
I will run the NVR software on either an i3-2100 or i7-3770.
The PC running the software also is a DIY nas.
I use home assistant for home automation and it is running a raspberry pi.
My gateway / router /...