DS-2CD2347G1-LU OEM software

xethax

xethax

n3wb
Aug 30, 2020
10
1
Netherlands
Goodmorning,

I have 2 Hikvision OEM camera's and my question is how do i update/upgrade these ones. (they are OEM)
The cameras are DS-2CD2347G1-LU and DS-2CD2385FWD-I.

Want to update the Colorvu to V5.6.2. build 200407 so i can use Led events. (led while only go on when there is a detection of motion)
 
xethax said:
I have 2 Hikvision OEM camera's and my question is how do i update/upgrade these ones. (they are OEM)
The cameras are DS-2CD2347G1-LU and DS-2CD2385FWD-I.
Click to expand...
The model numbers you have quoted are normal Hikvision ones.
The Hikvision stock firmware for those models is here :

DOWNLOAD EU PORTAL

www.hikvisioneurope.com www.hikvisioneurope.com

But from what I've seen, none of those firmware versions supports the 'turn on the LEDs on motion event' linkage capability.

There has been one firmware version that does this on the DS-2CD2347G1-LU - see this post :

Review of the Hikvision OEM model IPC-T2347G-LU 'ColorVu' IP CCTV camera.

Cheers, I managed to figure it out in the end from a post I found on another forum. The next challenge is creating a waterproof seal around my CAT6 cable using the gland on the junction box. The diameter of the hole in the rubber washer is way too big to grab the cable. I’ve been looking around...
ipcamtalk.com ipcamtalk.com
 
alastairstevenson said:
The model numbers you have quoted are normal Hikvision ones.
The Hikvision stock firmware for those models is here :

DOWNLOAD EU PORTAL

www.hikvisioneurope.com www.hikvisioneurope.com

But from what I've seen, none of those firmware versions supports the 'turn on the LEDs on motion event' linkage capability.

There has been one firmware version that does this on the DS-2CD2347G1-LU - see this post :

Review of the Hikvision OEM model IPC-T2347G-LU 'ColorVu' IP CCTV camera.

Cheers, I managed to figure it out in the end from a post I found on another forum. The next challenge is creating a waterproof seal around my CAT6 cable using the gland on the junction box. The diameter of the hole in the rubber washer is way too big to grab the cable. I’ve been looking around...
ipcamtalk.com ipcamtalk.com
Click to expand...



The model numbers are: DT347G-U (DS-2CD2347G1-LU) and DT385-I (DS-2CD2385FWD-I)
I tried the original software from the portal but no luck :(

Here a link to the firmware i need: DS-2CD2347G1-L(U) Hikvision 4 MP ColorVu Fixed Turret Network Camera
This firmware includes the trigger on event Led on.
 
xethax said:
This firmware includes the trigger on event Led on.
Click to expand...
Yes, I've tested that 5.6.2 firmware on a DS-2CD2347G1-LU ColorVu.
And it does have the capability for a motion event linkage to turn on the LEDs.
Despite all the newer stock versions up to 5.6.5 from here :

DOWNLOAD EU PORTAL

www.hikvisioneurope.com www.hikvisioneurope.com

oddly not having that capability.

If your OEM camera firmware is rejecting attempts to apply the stock firmware as it's respecting the mismatch of the OEM code, you'd have to try the tftp updater method, which does less validation and might just ignore the OEM code.
But because the firmware filesize is above the 32MB size limit of the Hikvsion tftp updater, you'd need to try Scott Lamb's python clone, here :
github.com

GitHub - scottlamb/hikvision-tftpd: Unbrick a Hikvision device (NVR or camera) via TFTP

Unbrick a Hikvision device (NVR or camera) via TFTP - scottlamb/hikvision-tftpd
github.com github.com
 
alastairstevenson said:
If your OEM camera firmware is rejecting attempts to apply the stock firmware as it's respecting the mismatch of the OEM code, you'd have to try the tftp updater method, which does less validation and might just ignore the OEM code.
But because the firmware filesize is above the 32MB size limit of the Hikvsion tftp updater, you'd need to try Scott Lamb's python clone, here :
github.com

GitHub - scottlamb/hikvision-tftpd: Unbrick a Hikvision device (NVR or camera) via TFTP

Unbrick a Hikvision device (NVR or camera) via TFTP - scottlamb/hikvision-tftpd
github.com github.com
Click to expand...
I tried the Scottlamb tftp method but i think i'm doing something wrong.
Wireshark shows me enough traffic but i can't find why its not working.
Tried both ip adresses...
 
xethax said:
I see the UDP probe from the server
Click to expand...
No - the UDP probe comes from the camera, usually from source address 192.0.0.64, to the server on destination 192.0.0.128
It can be blocked inbound to the PC if the Windows firewall doesn't have an inbound rule, or isn't temporarily disabled.
 
alastairstevenson said:
No - the UDP probe comes from the camera, usually from source address 192.0.0.64, to the server on destination 192.0.0.128
It can be blocked inbound to the PC if the Windows firewall doesn't have an inbound rule, or isn't temporarily disabled.
Click to expand...
Turned Windows Firewall off, and still nothing.
 

Attachments

  • dump.jpg
    dump.jpg
    907.8 KB · Views: 7
If you want to take this experiment further - a connection to the serial console will give direct access to the update program.
From what I recall, that model has a serial console connector under the SD card hatch.

That would need a USB to serial TTL convertor, such as a PL2303TA-based one.
A 4-pin 1.5mm JST ZH wired connector.
 
alastairstevenson said:
If you want to take this experiment further - a connection to the serial console will give direct access to the update program.
From what I recall, that model has a serial console connector under the SD card hatch.

That would need a USB to serial TTL convertor, such as a PL2303TA-based one.
A 4-pin 1.5mm JST ZH wired connector.
Click to expand...
if i had those connectors i would try it.
But i think i wait for a new way to update or something :P
 
xethax said:
only a change in serverip?
Click to expand...
Yes. My network at home is 192.168.1.x, so i was able to update without unplugging the camera from the network.

After the update i was unable to access the webinterface, but reboot fixed that..
 
I see that the IP in the camera is fixed at 192.168.1.64.. So maybe this is required.
 
You must log in or register to reply here.
Top Bottom