Hikvision Camera problem

[Click4]

Hi,

Thank you in advance for any help and advice.

Right, problem im having.

I have purchased all of these cameras previously elsewhere on eBay as where these cameras came from...previous ones worked fine, and it means I have a reasonable idea of what the cameras should and shouldnt do.

So, this time round, purchased the following cameras.

4x DS-2CD2732F-IS
1x DS-2CD2532F-IS
1x DS-2CD2632F-IS

Purchased 5 of the cameras from the same seller, the 5 being the 4x DS-2CD2732F-IS and the DS-2CD2632F-IS

now, 1 of the DS-2CD2732F-IS cameras, the DS-2CD2532F-IS and the DS-2CD2632F-IS are all running firmware V5.2.5 and have CH in the serial so assuming chinese market cameras, and all 3 of those cameras show up like this,

Number of Channels	1
Number of HDDs	1
Number of Alarm Input	1
Number of Alarm Output	1

and all 3 cameras recognise the internal SD memory card, and 2 of those cameras both have auto iris as an option under video... as have the previous cameras ive purchased... so all fine.

However, the other 3 DS-2CD2732F-IS cameras are all running firmware, V5.3.0 build 150814 and do not have CH in the serial... but the problem im having is that they show up like this.

Number of Channels	1
Number of HDDs	0
Number of Alarm Input	0
Number of Alarm Output	0

 

[Click4]

Corrected post, posted wrong firmware version mistakenly for 3 working cameras, those cams have v5.2.5 and CH in serial... so cannot be upgraded otherwise will go into chinese... but they are all working fine.

Its the 3 cams which are US/EU serial which have 5.3 and arent working.

Just found another post, where somebody was having similar problem with the SD card,

https://www.ipcamtalk.com/showthread.php/4950-DS-2CD2132F-IS-not-recognizing-local-mircoSD-card

Also,

https://www.ipcamtalk.com/showthread.php/4950-DS-2CD2132F-IS-not-recognizing-local-mircoSD-card?p=44609&viewfull=1#post44609

no evidence of the SD card hardware driver initialising, which suggests the hardware doesn't exist or is not recognised. Despite the 'MMC0,1 power register probe OK'.
And there is the dummy audio driver being loaded, which again suggests no audio hardware is present or recognised.

Which sounds similar to the problem I am experiencing with the audio not working, and SD card not recognised.
Maybe these are a fake? and there is no hardware present?

Should definitely have auto iris, and audio and alarm because I checked the Hikvision spec sheet and it lists them features.

http://www.hikvision.com/UploadFile/image/2014052616051552557.pdf

 

[alastairstevenson]

Can you grab a copy of the kernel log if the camera firmware still allows you telnet or SSH access?
It may provide some clues / evidence for the seller.
Either
cat /proc/kmsg
or
dmesg
depending on what commands are allowed in the shell.

 

[Click4]

Hi,

Thank you for your reply. I have enabled and checked 2 of the 3 dome cameras.

Enabled SSH, then run command "dmesg"

Camera 1,

Model	DS-2CD2732F-IS
Serial No.	DS-2CD2732F-IS20150317CCWR321364435
Firmware Version	V5.3.0 build 150814
Encoding Version	V5.0 build 150327
Number of Channels	1
Number of HDDs	0
Number of Alarm Input	0
Number of Alarm Output	0

BusyBox v1.19.3 (2015-03-20 17:37:48 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

BusyBox v1.2.1 Protect Shell (psh)
Enter 'help' for a list of davinci system commands.

# dmesg
[ 0.000000] Linux version 2.6.38.8 (chenyuanming@Cpl-Frt-BSP) (gcc version 4. 6.1 (Sourcery CodeBench Lite 2011.09-70) )
[ 0.000000] #4 PREEMPT Thu Mar 26 11:21:20 CST 2015
[ 0.000000] CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
[ 0.000000] Machine: Coconut
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Ambarella: AHB = 0x60000000[0xf0000000],0x01000000 0
[ 0.000000] Ambarella: APB = 0x70000000[0xf1000000],0x01000000 0
[ 0.000000] Ambarella: PPM = 0xc0000000[0xe0000000],0x00200000 9
[ 0.000000] Ambarella: BSB = 0xc8c00000[0xe8c00000],0x00400000 9
[ 0.000000] Ambarella: DSP = 0xc9000000[0xe9000000],0x07000000 9
[ 0.000000] Ambarella: HAL = 0xc00a0000[0xfee00000],0x0000e708 9
[ 0.000000] On node 0 totalpages: 25344
[ 0.000000] free_area_init_node: node 0, pgdat c04df128, node_mem_map c050500 0
[ 0.000000] Normal zone: 198 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 25146 pages, LIFO batch:7
[ 0.000000] bootmem_init: high_memory = 0xc8a00000
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 25146
[ 0.000000] Kernel command line: console=ttyS0 initrd=0xc0a00000,0x400000 rw root=/dev/ram dbg=0 KRN_PRT=pri RMD_PRT=pri reserved=0xc6500000,0x100000,99 vide o=amb0fb:720x480,720x480,1,0
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 99MB = 99MB total
[ 0.000000] Memory: 91184k/91184k available, 10192k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfe600000 - 0xfee00000 ( 8 MB)
[ 0.000000] vmalloc : 0xc9000000 - 0xe0000000 ( 368 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8a00000 ( 138 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc04ac000 (4604 kB)
[ 0.000000] .data : 0xc04ac000 - 0xc04df7e0 ( 206 kB)
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:224
[ 0.000000] sched_clock: 32 bits at 72MHz, resolution 13ns, wraps every 59652 ms
[ 0.000000] sched_clock: wrong multiply/shift: 1864135111>>27 vs calculated 3 728270222>>28
[ 0.000000] sched_clock: fix multiply/shift to avoid scheduler hiccups
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.000590] Calibrating delay loop... 525.92 BogoMIPS (lpj=2629632)
[ 0.260136] pid_max: default: 32768 minimum: 301
[ 0.260567] Mount-cache hash table entries: 512
[ 0.261363] CPU: Testing write buffer coherency: ok
[ 0.268014] NET: Registered protocol family 16
[ 0.278954] Ambarella Coconut:
[ 0.278988] chip id: 5100
[ 0.279004] board type: 3
[ 0.279017] board revision: 10
[ 0.279031] chip name: a5m
[ 0.279044] HAL version: 176869
[ 0.279060] reference clock: 24000000
[ 0.279078] system configuration: 0x040004ea
[ 0.279096] boot type: 0x00000002
[ 0.279112] hif type: 0x00000000
[ 0.307368] bio: create slab <bio-0> at 0
[ 0.309949] ambarella-spi ambarella-spi.0: ambarella SPI Controller 0 created
[ 0.321098] ambarella-i2c ambarella-i2c.0: Ambarella Media Processor I2C adap ter[i2c-0] probed!
[ 0.322672] ambarella-i2c ambarella-i2c.1: Ambarella Media Processor I2C adap ter[i2c-1] probed!
[ 0.324117] i2c i2c-0: Added multiplexed i2c bus 2
[ 0.324159] ambarella-i2cmux ambarella-i2cmux.0: mux on ambarella-i2c adapter
[ 0.327126] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.331412] cfg80211: Calling CRDA to update world regulatory domain
[ 0.333094] Switching to clocksource ambarella-cs-timer
[ 0.340189] Switched to NOHz mode on CPU #0
[ 0.397221] NET: Registered protocol family 2
[ 0.397586] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.398521] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.398728] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.398873] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.398896] TCP reno registered
[ 0.398924] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.398970] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.399611] NET: Registered protocol family 1
[ 0.400534] RPC: Registered udp transport module.
[ 0.400573] RPC: Registered tcp transport module.
[ 0.400593] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.401122] Trying to unpack rootfs image as initramfs...
[ 0.403790] rootfs image is not initramfs (no cpio magic); looks like an init rd
[ 0.438032] Freeing initrd memory: 4096K
[ 0.441090] [ kernel version: svn-120249 ]
[ 0.441195] mmc0 power register success!
[ 0.441238] mmc1 power register success!
[ 0.441373] reboot times :1
[ 0.465044] msgmni has been set to 186
[ 0.473918] alg: No test for stdrng (krng)
[ 0.474084] io scheduler noop registered
[ 0.474113] io scheduler deadline registered
[ 0.474296] io scheduler cfq registered (default)
[ 0.478040] ambarella-fb ambarella-fb.0: probe p[720x480] v[720x576] c[1] b[0 ] l[736] @ [0xc5980000:0x00068000]!
[ 0.479896] ambarella-uart.0: ttyS0 at MMIO 0x70005000 (irq = 9) is a ambuart
[ 0.516444] brd: module loaded
[ 0.530933] loop: module loaded
[ 0.534523] NAND device: Manufacturer ID: 0x98, Chip ID: 0xd1 (Toshiba NAND 1 28MiB 3,3V 8-bit)
[ 0.534572] ambarella_nand_config_flash: 0x02e00140, 0x02c00140
[ 0.535004] Bad block table found at page 65472, version 0x01
[ 0.535537] Bad block table found at page 65408, version 0x01
[ 0.541435] ambarella-nand ambarella-nand: ambarella_nand_probe: Partition in fomation found!
[ 0.541504] Creating 18 MTD partitions on "ambnand":
[ 0.541541] 0x000000000000-0x000000020000 : "bst"
[ 0.545759] 0x000000020000-0x000000120000 : "ptb"
[ 0.549572] 0x000000120000-0x000000220000 : "bld"
[ 0.553650] 0x000000220000-0x000000320000 : "hal"
[ 0.557573] 0x000000320000-0x000000420000 : "ano_ptb"
[ 0.561497] 0x000000420000-0x0000004a0000 : "env"
[ 0.565776] 0x0000004a0000-0x000000520000 : "param"
[ 0.569826] 0x000000520000-0x000000620000 : "dpt"
[ 0.574122] 0x000000620000-0x000001020000 : "rcvy"
[ 0.578335] 0x000001020000-0x000001820000 : "krn_pri"
[ 0.582251] 0x000001820000-0x000002020000 : "krn_sec"
[ 0.586477] 0x000002020000-0x000002420000 : "rmd_pri"
[ 0.590452] 0x000002420000-0x000002820000 : "rmd_sec"
[ 0.594771] 0x000002820000-0x000004020000 : "app_pri"
[ 0.598902] 0x000004020000-0x000005820000 : "app_sec"
[ 0.603102] 0x000005820000-0x000005c20000 : "cfg_pri"
[ 0.607514] 0x000005c20000-0x000006020000 : "cfg_sec"
[ 0.611827] 0x000006020000-0x000007020000 : "dbg"
[ 0.623410] PPP generic driver version 2.4.2
[ 0.624838] PPP Deflate Compression module registered
[ 0.624882] PPP BSD Compression module registered
[ 0.818508] Ambarella MII Bus: probed
[ 0.820201] ambarella-eth ambarella-eth.0: MAC Address[48:11:b2:25:e4:b5].
[ 0.820940] console [netcon0] enabled
[ 0.820967] netconsole: network logging started
[ 0.822649] mousedev: PS/2 mouse device common for all mice
[ 0.823862] input: AmbInput as /devices/virtual/input/input0
[ 0.824894] ambarella_gpio_irq_set_wake: irq[75] = girq[11] = 1
[ 0.824939] ambarella-input ambarella-input: AmbInput probed!
[ 0.825967] ambarella-adc ambarella-adc: ADC Host Controller [polling mode] p robed!
[ 0.827655] ambarella-rtc ambarella-rtc: rtc core: registered ambarella-rtc a s rtc0
[ 0.828249] i2c /dev entries driver
[ 0.833109] ambarella-wdt ambarella-wdt: Ambarella Media Processor Watch Dog Timer[ambarella-wdt].
[ 0.840016] ALSA device list:
[ 0.840049] No soundcards found.
[ 0.840233] Netfilter messages via NETLINK v0.30.
[ 0.840434] nf_conntrack version 0.5.0 (1488 buckets, 5952 max)
[ 0.841106] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.841286] TCP cubic registered
[ 0.841722] NET: Registered protocol family 10
[ 0.844766] Mobile IPv6
[ 0.844902] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 0.845163] IPv6 over IPv4 tunneling driver
[ 0.849006] NET: Registered protocol family 17
[ 0.849855] sctp: Hash tables configured (established 4096 bind 8192)
[ 0.850208] sctp: sctp_init_sock(sk: c58d6b20)
[ 0.850331] lib80211: common routines for IEEE802.11 drivers
[ 0.850363] lib80211_crypt: registered algorithm 'NULL'
[ 0.854692] ambarella-rtc ambarella-rtc: setting system clock to 2015-12-21 1 4:32:35 UTC (1450708355)
[ 0.855524] RAMDISK: gzip image found at block 0
[ 1.711005] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 1.711221] Freeing init memory: 148K
[ 3.735842] UBI: attaching mtd13 to ubi1
[ 3.735884] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.735909] UBI: logical eraseblock size: 129024 bytes
[ 3.735928] UBI: smallest flash I/O unit: 2048
[ 3.735945] UBI: sub-page size: 512
[ 3.735963] UBI: VID header offset: 512 (aligned 512)
[ 3.735982] UBI: data offset: 2048
[ 3.795335] UBI: max. sequence number: 502
[ 3.813338] UBI: attached mtd13 to ubi1
[ 3.813373] UBI: MTD device name: "app_pri"
[ 3.813398] UBI: MTD device size: 24 MiB
[ 3.813416] UBI: number of good PEBs: 192
[ 3.813432] UBI: number of bad PEBs: 0
[ 3.813448] UBI: number of corrupted PEBs: 0
[ 3.813464] UBI: max. allowed volumes: 128
[ 3.813481] UBI: wear-leveling threshold: 4096
[ 3.813497] UBI: number of internal volumes: 1
[ 3.813513] UBI: number of user volumes: 1
[ 3.813528] UBI: available PEBs: 0
[ 3.813544] UBI: total number of reserved PEBs: 192
[ 3.813562] UBI: number of PEBs reserved for bad PEB handling: 2
[ 3.813582] UBI: max/mean erase counter: 12/8
[ 3.813598] UBI: image sequence number: 1183003353
[ 3.821689] UBI: background thread "ubi_bgt1d" started, PID 625
[ 3.905944] UBIFS: recovery needed
[ 3.939189] UBIFS: recovery completed
[ 3.939238] UBIFS: mounted UBI device 1, volume 0, name "app_pri"
[ 3.939267] UBIFS: file system size: 22837248 bytes (22302 KiB, 21 MiB, 177 LEBs)
[ 3.939295] UBIFS: journal size: 1161216 bytes (1134 KiB, 1 MiB, 9 LEBs )
[ 3.939319] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.939339] UBIFS: default compressor: lzo
[ 3.939357] UBIFS: reserved for root: 1078659 bytes (1053 KiB)
[ 3.978001] UBI: attaching mtd15 to ubi3
[ 3.978043] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.978067] UBI: logical eraseblock size: 129024 bytes
[ 3.978087] UBI: smallest flash I/O unit: 2048
[ 3.978104] UBI: sub-page size: 512
[ 3.978123] UBI: VID header offset: 512 (aligned 512)
[ 3.978143] UBI: data offset: 2048
[ 3.987025] UBI: max. sequence number: 188
[ 4.010545] UBI: attached mtd15 to ubi3
[ 4.010579] UBI: MTD device name: "cfg_pri"
[ 4.010601] UBI: MTD device size: 4 MiB
[ 4.010618] UBI: number of good PEBs: 32
[ 4.010634] UBI: number of bad PEBs: 0
[ 4.010649] UBI: number of corrupted PEBs: 0
[ 4.010666] UBI: max. allowed volumes: 128
[ 4.010683] UBI: wear-leveling threshold: 4096
[ 4.010699] UBI: number of internal volumes: 1
[ 4.010715] UBI: number of user volumes: 1
[ 4.010730] UBI: available PEBs: 0
[ 4.010746] UBI: total number of reserved PEBs: 32
[ 4.010763] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.010783] UBI: max/mean erase counter: 22/17
[ 4.010800] UBI: image sequence number: 412642354
[ 4.013321] UBI: background thread "ubi_bgt3d" started, PID 634
[ 4.094592] UBIFS: recovery needed
[ 4.128776] UBIFS: recovery completed
[ 4.128824] UBIFS: mounted UBI device 3, volume 0, name "cfg_pri"
[ 4.128853] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEB s)
[ 4.128881] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs )
[ 4.128905] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.128925] UBIFS: default compressor: lzo
[ 4.128943] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.271933] UBI: attaching mtd16 to ubi4
[ 4.271975] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 4.272000] UBI: logical eraseblock size: 129024 bytes
[ 4.272019] UBI: smallest flash I/O unit: 2048
[ 4.272035] UBI: sub-page size: 512
[ 4.272053] UBI: VID header offset: 512 (aligned 512)
[ 4.272072] UBI: data offset: 2048
[ 4.280864] UBI: max. sequence number: 192
[ 4.305250] UBI: attached mtd16 to ubi4
[ 4.305285] UBI: MTD device name: "cfg_sec"
[ 4.305308] UBI: MTD device size: 4 MiB
[ 4.305325] UBI: number of good PEBs: 32
[ 4.305341] UBI: number of bad PEBs: 0
[ 4.305357] UBI: number of corrupted PEBs: 0
[ 4.305373] UBI: max. allowed volumes: 128
[ 4.305389] UBI: wear-leveling threshold: 4096
[ 4.305406] UBI: number of internal volumes: 1
[ 4.305422] UBI: number of user volumes: 1
[ 4.305437] UBI: available PEBs: 0
[ 4.305453] UBI: total number of reserved PEBs: 32
[ 4.305471] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.305490] UBI: max/mean erase counter: 21/18
[ 4.305506] UBI: image sequence number: 35551842
[ 4.313804] UBI: background thread "ubi_bgt4d" started, PID 644
[ 4.389016] UBIFS: recovery needed
[ 4.426749] UBIFS: recovery completed
[ 4.426799] UBIFS: mounted UBI device 4, volume 0, name "cfg_sec"
[ 4.426827] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEB s)
[ 4.426854] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs )
[ 4.426879] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.426898] UBIFS: default compressor: lzo
[ 4.426916] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.656527] net eth0: Could not find default PHY in 9.
[ 4.656569] net eth0: Try PHY[9] whose id is 0x00008201!
[ 4.657795] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.653578] PHY: 0:09 - Link is Up - 100/Full
[ 6.653792] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.484893] dsp: module license 'Proprietary' taints kernel.
[ 8.484933] Disabling lock debugging due to kernel taint
[ 8.564458] img: aaa_fifo2_base malloc c5b50000
[ 8.986558] >>>>>> DSP LOG ADDR START PHY 0xc0080000
[ 8.986594] Init software HR timer for DSP communication
[ 9.016552] cdev_init rs485_fops ...
[ 9.016604] adding uart1, minor = 0
[ 9.020183] Successfully insmod uart232 module!
[ 9.165324] amba_debug_init 248:248.
[ 17.323235] eth0: no IPv6 routers present
[ 34.063888] AMBARELLA SoC Audio DUMMY Codec
[ 34.065409] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok
[ 34.938574] MT9T002 sensor ID is 0x2604
[ 34.992465] CMEMK module: built on Aug 23 2012 at 17:05:43
[ 34.992514] Reference Linux version 2.6.38
[ 34.992533] File /mnt/data_bsp/data_yuhuanhuan/raptor/a5s_svn2/kernel/hik_dr ivers/cmem/src/module/cmemk.c
[ 35.000273] cmemk initialized
[ 47.197385] iav error: Failed to wait for completion!

Camera 2,

Model	DS-2CD2732F-IS
Serial No.	DS-2CD2732F-IS20150327CCWR321334431
Firmware Version	V5.3.0 build 150814
Encoding Version	V5.0 build 150327
Number of Channels	1
Number of HDDs	0
Number of Alarm Input	0
Number of Alarm Output	0

BusyBox v1.19.3 (2015-03-20 17:37:48 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

BusyBox v1.2.1 Protect Shell (psh)
Enter 'help' for a list of davinci system commands.

# dmesg
[ 0.000000] Linux version 2.6.38.8 (chenyuanming@Cpl-Frt-BSP) (gcc version 4. 6.1 (Sourcery CodeBench Lite 2011.09-70) )
[ 0.000000] #4 PREEMPT Thu Mar 26 11:21:20 CST 2015
[ 0.000000] CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
[ 0.000000] Machine: Coconut
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Ambarella: AHB = 0x60000000[0xf0000000],0x01000000 0
[ 0.000000] Ambarella: APB = 0x70000000[0xf1000000],0x01000000 0
[ 0.000000] Ambarella: PPM = 0xc0000000[0xe0000000],0x00200000 9
[ 0.000000] Ambarella: BSB = 0xc8c00000[0xe8c00000],0x00400000 9
[ 0.000000] Ambarella: DSP = 0xc9000000[0xe9000000],0x07000000 9
[ 0.000000] Ambarella: HAL = 0xc00a0000[0xfee00000],0x0000e708 9
[ 0.000000] On node 0 totalpages: 25344
[ 0.000000] free_area_init_node: node 0, pgdat c04df128, node_mem_map c050500 0
[ 0.000000] Normal zone: 198 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 25146 pages, LIFO batch:7
[ 0.000000] bootmem_init: high_memory = 0xc8a00000
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 25146
[ 0.000000] Kernel command line: console=ttyS0 initrd=0xc0a00000,0x400000 rw root=/dev/ram dbg=0 KRN_PRT=pri RMD_PRT=pri reserved=0xc6500000,0x100000,99 vide o=amb0fb:720x480,720x480,1,0
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 99MB = 99MB total
[ 0.000000] Memory: 91184k/91184k available, 10192k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfe600000 - 0xfee00000 ( 8 MB)
[ 0.000000] vmalloc : 0xc9000000 - 0xe0000000 ( 368 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8a00000 ( 138 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc04ac000 (4604 kB)
[ 0.000000] .data : 0xc04ac000 - 0xc04df7e0 ( 206 kB)
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:224
[ 0.000000] sched_clock: 32 bits at 72MHz, resolution 13ns, wraps every 59652 ms
[ 0.000000] sched_clock: wrong multiply/shift: 1864135111>>27 vs calculated 3 728270222>>28
[ 0.000000] sched_clock: fix multiply/shift to avoid scheduler hiccups
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.000593] Calibrating delay loop... 525.92 BogoMIPS (lpj=2629632)
[ 0.260138] pid_max: default: 32768 minimum: 301
[ 0.260567] Mount-cache hash table entries: 512
[ 0.261361] CPU: Testing write buffer coherency: ok
[ 0.268033] NET: Registered protocol family 16
[ 0.278990] Ambarella Coconut:
[ 0.279025] chip id: 5100
[ 0.279041] board type: 3
[ 0.279054] board revision: 10
[ 0.279067] chip name: a5m
[ 0.279080] HAL version: 176869
[ 0.279096] reference clock: 24000000
[ 0.279113] system configuration: 0x177804ea
[ 0.279131] boot type: 0x00000002
[ 0.279146] hif type: 0x00000000
[ 0.307324] bio: create slab <bio-0> at 0
[ 0.309900] ambarella-spi ambarella-spi.0: ambarella SPI Controller 0 created
[ 0.321026] ambarella-i2c ambarella-i2c.0: Ambarella Media Processor I2C adap ter[i2c-0] probed!
[ 0.322611] ambarella-i2c ambarella-i2c.1: Ambarella Media Processor I2C adap ter[i2c-1] probed!
[ 0.324062] i2c i2c-0: Added multiplexed i2c bus 2
[ 0.324104] ambarella-i2cmux ambarella-i2cmux.0: mux on ambarella-i2c adapter
[ 0.327050] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.331313] cfg80211: Calling CRDA to update world regulatory domain
[ 0.332992] Switching to clocksource ambarella-cs-timer
[ 0.340186] Switched to NOHz mode on CPU #0
[ 0.397087] NET: Registered protocol family 2
[ 0.397454] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.398381] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.398588] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.398732] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.398754] TCP reno registered
[ 0.398781] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.398826] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.399461] NET: Registered protocol family 1
[ 0.400381] RPC: Registered udp transport module.
[ 0.400419] RPC: Registered tcp transport module.
[ 0.400438] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.400962] Trying to unpack rootfs image as initramfs...
[ 0.403643] rootfs image is not initramfs (no cpio magic); looks like an init rd
[ 0.437960] Freeing initrd memory: 4096K
[ 0.440983] [ kernel version: svn-120249 ]
[ 0.441090] mmc0 power register success!
[ 0.441132] mmc1 power register success!
[ 0.441268] reboot times :1
[ 0.464927] msgmni has been set to 186
[ 0.473793] alg: No test for stdrng (krng)
[ 0.473962] io scheduler noop registered
[ 0.473993] io scheduler deadline registered
[ 0.474180] io scheduler cfq registered (default)
[ 0.477914] ambarella-fb ambarella-fb.0: probe p[720x480] v[720x576] c[1] b[0 ] l[736] @ [0xc5980000:0x00068000]!
[ 0.479768] ambarella-uart.0: ttyS0 at MMIO 0x70005000 (irq = 9) is a ambuart
[ 0.516333] brd: module loaded
[ 0.530829] loop: module loaded
[ 0.534438] NAND device: Manufacturer ID: 0x98, Chip ID: 0xd1 (Toshiba NAND 1 28MiB 3,3V 8-bit)
[ 0.534486] ambarella_nand_config_flash: 0x02e00140, 0x02c00140
[ 0.534918] Bad block table found at page 65472, version 0x01
[ 0.535445] Bad block table found at page 65408, version 0x01
[ 0.541285] ambarella-nand ambarella-nand: ambarella_nand_probe: Partition in fomation found!
[ 0.541353] Creating 18 MTD partitions on "ambnand":
[ 0.541392] 0x000000000000-0x000000020000 : "bst"
[ 0.545615] 0x000000020000-0x000000120000 : "ptb"
[ 0.549412] 0x000000120000-0x000000220000 : "bld"
[ 0.553514] 0x000000220000-0x000000320000 : "hal"
[ 0.557420] 0x000000320000-0x000000420000 : "ano_ptb"
[ 0.561351] 0x000000420000-0x0000004a0000 : "env"
[ 0.565632] 0x0000004a0000-0x000000520000 : "param"
[ 0.569666] 0x000000520000-0x000000620000 : "dpt"
[ 0.573987] 0x000000620000-0x000001020000 : "rcvy"
[ 0.578177] 0x000001020000-0x000001820000 : "krn_pri"
[ 0.582104] 0x000001820000-0x000002020000 : "krn_sec"
[ 0.586346] 0x000002020000-0x000002420000 : "rmd_pri"
[ 0.590337] 0x000002420000-0x000002820000 : "rmd_sec"
[ 0.594671] 0x000002820000-0x000004020000 : "app_pri"
[ 0.598824] 0x000004020000-0x000005820000 : "app_sec"
[ 0.603288] 0x000005820000-0x000005c20000 : "cfg_pri"
[ 0.607453] 0x000005c20000-0x000006020000 : "cfg_sec"
[ 0.611763] 0x000006020000-0x000007020000 : "dbg"
[ 0.623327] PPP generic driver version 2.4.2
[ 0.624751] PPP Deflate Compression module registered
[ 0.624794] PPP BSD Compression module registered
[ 0.818406] Ambarella MII Bus: probed
[ 0.820086] ambarella-eth ambarella-eth.0: MAC Address[48:11:b2:26:e4:bc].
[ 0.820821] console [netcon0] enabled
[ 0.820852] netconsole: network logging started
[ 0.822525] mousedev: PS/2 mouse device common for all mice
[ 0.823743] input: AmbInput as /devices/virtual/input/input0
[ 0.824770] ambarella_gpio_irq_set_wake: irq[75] = girq[11] = 1
[ 0.824816] ambarella-input ambarella-input: AmbInput probed!
[ 0.825839] ambarella-adc ambarella-adc: ADC Host Controller [polling mode] p robed!
[ 0.827531] ambarella-rtc ambarella-rtc: rtc core: registered ambarella-rtc a s rtc0
[ 0.828122] i2c /dev entries driver
[ 0.832980] ambarella-wdt ambarella-wdt: Ambarella Media Processor Watch Dog Timer[ambarella-wdt].
[ 0.839877] ALSA device list:
[ 0.839912] No soundcards found.
[ 0.840098] Netfilter messages via NETLINK v0.30.
[ 0.840297] nf_conntrack version 0.5.0 (1488 buckets, 5952 max)
[ 0.840966] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.841144] TCP cubic registered
[ 0.841583] NET: Registered protocol family 10
[ 0.844609] Mobile IPv6
[ 0.844743] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 0.845000] IPv6 over IPv4 tunneling driver
[ 0.848848] NET: Registered protocol family 17
[ 0.849692] sctp: Hash tables configured (established 4096 bind 8192)
[ 0.850044] sctp: sctp_init_sock(sk: c58d6b20)
[ 0.850167] lib80211: common routines for IEEE802.11 drivers
[ 0.850198] lib80211_crypt: registered algorithm 'NULL'
[ 0.854535] ambarella-rtc ambarella-rtc: setting system clock to 2015-12-21 1 4:32:38 UTC (1450708358)
[ 0.855365] RAMDISK: gzip image found at block 0
[ 1.710554] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 1.710767] Freeing init memory: 148K
[ 3.749869] UBI: attaching mtd13 to ubi1
[ 3.749911] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.749937] UBI: logical eraseblock size: 129024 bytes
[ 3.749956] UBI: smallest flash I/O unit: 2048
[ 3.749973] UBI: sub-page size: 512
[ 3.749991] UBI: VID header offset: 512 (aligned 512)
[ 3.750011] UBI: data offset: 2048
[ 3.809877] UBI: max. sequence number: 544
[ 3.835898] UBI: attached mtd13 to ubi1
[ 3.835931] UBI: MTD device name: "app_pri"
[ 3.835955] UBI: MTD device size: 24 MiB
[ 3.835972] UBI: number of good PEBs: 192
[ 3.835988] UBI: number of bad PEBs: 0
[ 3.836004] UBI: number of corrupted PEBs: 0
[ 3.836020] UBI: max. allowed volumes: 128
[ 3.836037] UBI: wear-leveling threshold: 4096
[ 3.836053] UBI: number of internal volumes: 1
[ 3.836069] UBI: number of user volumes: 1
[ 3.836084] UBI: available PEBs: 0
[ 3.836100] UBI: total number of reserved PEBs: 192
[ 3.836118] UBI: number of PEBs reserved for bad PEB handling: 2
[ 3.836138] UBI: max/mean erase counter: 12/9
[ 3.836154] UBI: image sequence number: 2037183791
[ 3.844418] UBI: background thread "ubi_bgt1d" started, PID 625
[ 3.919147] UBIFS: recovery needed
[ 3.957594] UBIFS: recovery completed
[ 3.957642] UBIFS: mounted UBI device 1, volume 0, name "app_pri"
[ 3.957670] UBIFS: file system size: 22837248 bytes (22302 KiB, 21 MiB, 177 LEBs)
[ 3.957698] UBIFS: journal size: 1161216 bytes (1134 KiB, 1 MiB, 9 LEBs )
[ 3.957722] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.957740] UBIFS: default compressor: lzo
[ 3.957758] UBIFS: reserved for root: 1078659 bytes (1053 KiB)
[ 3.996472] UBI: attaching mtd15 to ubi3
[ 3.996514] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.996538] UBI: logical eraseblock size: 129024 bytes
[ 3.996557] UBI: smallest flash I/O unit: 2048
[ 3.996574] UBI: sub-page size: 512
[ 3.996592] UBI: VID header offset: 512 (aligned 512)
[ 3.996612] UBI: data offset: 2048
[ 4.005474] UBI: max. sequence number: 244
[ 4.029010] UBI: attached mtd15 to ubi3
[ 4.029044] UBI: MTD device name: "cfg_pri"
[ 4.029066] UBI: MTD device size: 4 MiB
[ 4.029083] UBI: number of good PEBs: 32
[ 4.029099] UBI: number of bad PEBs: 0
[ 4.029115] UBI: number of corrupted PEBs: 0
[ 4.029131] UBI: max. allowed volumes: 128
[ 4.029148] UBI: wear-leveling threshold: 4096
[ 4.029164] UBI: number of internal volumes: 1
[ 4.029180] UBI: number of user volumes: 1
[ 4.029195] UBI: available PEBs: 0
[ 4.029211] UBI: total number of reserved PEBs: 32
[ 4.029229] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.029249] UBI: max/mean erase counter: 26/22
[ 4.029266] UBI: image sequence number: 1818405271
[ 4.033209] UBI: background thread "ubi_bgt3d" started, PID 634
[ 4.113005] UBIFS: recovery needed
[ 4.162962] UBIFS: recovery completed
[ 4.163010] UBIFS: mounted UBI device 3, volume 0, name "cfg_pri"
[ 4.163037] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEB s)
[ 4.163173] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs )
[ 4.163205] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.163228] UBIFS: default compressor: lzo
[ 4.163246] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.305536] UBI: attaching mtd16 to ubi4
[ 4.305579] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 4.305603] UBI: logical eraseblock size: 129024 bytes
[ 4.305622] UBI: smallest flash I/O unit: 2048
[ 4.305639] UBI: sub-page size: 512
[ 4.305656] UBI: VID header offset: 512 (aligned 512)
[ 4.305675] UBI: data offset: 2048
[ 4.314384] UBI: max. sequence number: 246
[ 4.338021] UBI: attached mtd16 to ubi4
[ 4.338055] UBI: MTD device name: "cfg_sec"
[ 4.338076] UBI: MTD device size: 4 MiB
[ 4.338094] UBI: number of good PEBs: 32
[ 4.338110] UBI: number of bad PEBs: 0
[ 4.338126] UBI: number of corrupted PEBs: 0
[ 4.338141] UBI: max. allowed volumes: 128
[ 4.338158] UBI: wear-leveling threshold: 4096
[ 4.338174] UBI: number of internal volumes: 1
[ 4.338189] UBI: number of user volumes: 1
[ 4.338205] UBI: available PEBs: 0
[ 4.338220] UBI: total number of reserved PEBs: 32
[ 4.338238] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.338258] UBI: max/mean erase counter: 25/22
[ 4.338274] UBI: image sequence number: 998041809
[ 4.343265] UBI: background thread "ubi_bgt4d" started, PID 644
[ 4.421660] UBIFS: recovery needed
[ 4.472606] UBIFS: recovery completed
[ 4.472654] UBIFS: mounted UBI device 4, volume 0, name "cfg_sec"
[ 4.472682] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEB s)
[ 4.472709] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs )
[ 4.472734] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.472753] UBIFS: default compressor: lzo
[ 4.472771] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.700461] net eth0: Could not find default PHY in 9.
[ 4.700503] net eth0: Try PHY[9] whose id is 0x00008201!
[ 4.701727] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.693455] PHY: 0:09 - Link is Up - 100/Full
[ 6.693666] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.522762] dsp: module license 'Proprietary' taints kernel.
[ 8.522802] Disabling lock debugging due to kernel taint
[ 8.602215] img: aaa_fifo2_base malloc c5b50000
[ 9.023784] >>>>>> DSP LOG ADDR START PHY 0xc0080000
[ 9.023817] Init software HR timer for DSP communication
[ 9.053871] cdev_init rs485_fops ...
[ 9.053924] adding uart1, minor = 0
[ 9.057486] Successfully insmod uart232 module!
[ 9.202089] amba_debug_init 248:248.
[ 16.963142] eth0: no IPv6 routers present
[ 34.098988] AMBARELLA SoC Audio DUMMY Codec
[ 34.100512] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok
[ 34.971896] MT9T002 sensor ID is 0x2604
[ 35.025896] CMEMK module: built on Aug 23 2012 at 17:05:43
[ 35.025942] Reference Linux version 2.6.38
[ 35.025961] File /mnt/data_bsp/data_yuhuanhuan/raptor/a5s_svn2/kernel/hik_dr ivers/cmem/src/module/cmemk.c
[ 35.038567] cmemk initialized
[ 51.646868] iav error: Failed to wait for completion!

dont really know what im looking at lol, but both do say, [ 0.839912] No soundcards found.

Which coincides i guess with the lack of audio options despite having audio wiring!

 

[Click4]

Tried cat /proc/kmsg, didnt work.

Heres list it says of supported commands if an alternative command will work?

Support Commands:
taskShow printPart prtHardInfo
getPreviewStatus setIp setV6ip
setGateway dspStatus outputClose
outputOpen getDebug setDebug
debugLog getIrstate getMtu
camCmd getCamVer getIrstate
getLux getMcuInfo getMotion
getRawdata setIrcmd setRectFrame
updateCamera setLaserMode getLaserMode
setIrMode getIrMode setBaiguangMode
getBaiguangMode setYTLock InquireFanSwitch
StartLaser CloseLaser LaserMotReset
EnlargeCur ReduceCur SetCur
LaserMotDirect LaserTeleOffset LaserWideOffset
InqSwitch InqCurrent InqCurMotDirect
getMcuStateInfo setFastFocus getTrackStatus
getSelfcheckResult setLdcMode getLdcMode
getPreviewStatus appCmd camCmd
ezoomlens_start_t2_test prtLensCurve getLensCurve
getIp gdbcfg {Test1}
{Test2} {Test3} {Test4}
{TestN} {TestY} getIsp
getISP setIsp setISP
setAgingMode getAgingMode setAgingTime
getAgingTime setLensZoomPos getLensZoomPos
dm365 ss showKey
showServer showUpnp showStatus
showDefence setLBS setAlarm
cloudService t1 ifconfig
netstat ping ping6
top iostat mpstat
ps reset dmesg
getDateInfo diagnose help

 

[alastairstevenson]

dmesg is fine, it gives the needed information.
From what I can see - the sound driver does not find any sound hardware.
So either the hardware exists and the driver is not compatible - or the hardware is not responding, may not exist.
PCBs usually have optional areas to populate or not during manufacture. I'd guess these are missing the sound components, maybe a manufacturing mixup given the sound connectors.
And no mention in the log of an MMC device.

Camera 1
[ 0.840016] ALSA device list:
[ 0.840049] No soundcards found.
[ 34.063888] AMBARELLA SoC Audio DUMMY Codec
[ 34.065409] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok

Camera 2
[ 0.839877] ALSA device list:
[ 0.839912] No soundcards found.
[ 34.098988] AMBARELLA SoC Audio DUMMY Codec
[ 34.100512] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok

If you are curious - you could compare with the other cameras.

 

[Click4]

will do tomorrow, thanks.

the last remaining camera I need to get down, repackage it for return.. so i will do the SSH interogation on the working camera also and compare it to above.

I dont know what to think to be honest... the cameras look perfectly legitimate and genuine... ive purchased 9 Hikvision cameras previously, and this time again 6, 3 of which are the bad dome cameras.

So I know what genuine ones look like, the casings look genuine, the packaging and included accessories all look genuine, board looks genuine.. doesnt look like a poor copy.. the serial numbers are all unique, and the WR serial ones are even running latest firmware fine.

So everything points to them being genuine.

However, they did not do this model of camera without SD or Auto Iris capability, it was alarm and audio which was optional with the S on the end of the model number.

However it seems these 3 units are missing the hardware for the SD Card, Audio, and Alarm, despite having the wiring connectors and socket for them.

surely thats 1 heck of a manufacturing error to install an SD card socket on the board but no hardware to make it useable? surely that would make it a reject item? but then what are the chances of having 3 cameras on same order with exact same fault?

funny thing is, i confronted seller about this, and they claim that all their cameras that they are aware of done have auto iris on this model.. so they tried to say it was not a feature that is missing.

couldnt answer though why the chinese region one i purchased from them on same order, from same ebay listing had auto iris though, why hikvision say,

http://www.hikvision.com/UploadFile/image/2015042010434977900.pdf

on that pdf it has auto iris, and why on the previous 4 of these camera models ive fitted they all have auto iris!

So wherever they are getting their stock from, looks like its all defective stock... just because the features which are missing are the ones which arent commonly used.. maybe nobody else has noticed?

 

[Click4]

Hi, here is the SSH output from the 3rd faulty camera.

# dmesg
[ 0.000000] Linux version 2.6.38.8 (chenyuanming@Cpl-Frt-BSP) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-70) )
[ 0.000000] #4 PREEMPT Thu Mar 26 11:21:20 CST 2015
[ 0.000000] CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Coconut
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Ambarella: AHB = 0x60000000[0xf0000000],0x01000000 0
[ 0.000000] Ambarella: APB = 0x70000000[0xf1000000],0x01000000 0
[ 0.000000] Ambarella: PPM = 0xc0000000[0xe0000000],0x00200000 9
[ 0.000000] Ambarella: BSB = 0xc8c00000[0xe8c00000],0x00400000 9
[ 0.000000] Ambarella: DSP = 0xc9000000[0xe9000000],0x07000000 9
[ 0.000000] Ambarella: HAL = 0xc00a0000[0xfee00000],0x0000e708 9
[ 0.000000] On node 0 totalpages: 25344
[ 0.000000] free_area_init_node: node 0, pgdat c04df128, node_mem_map c0505000
[ 0.000000] Normal zone: 198 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 25146 pages, LIFO batch:7
[ 0.000000] bootmem_init: high_memory = 0xc8a00000
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 25146
[ 0.000000] Kernel command line: console=ttyS0 initrd=0xc0a00000,0x400000 rw root=/dev/ram dbg=0 KRN_PRT=pri RMD_PRT=pri reserved=0xc6500000,0x100000,99 video=amb0fb:720x480,720x480,1,0
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 99MB = 99MB total
[ 0.000000] Memory: 91184k/91184k available, 10192k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfe600000 - 0xfee00000 ( 8 MB)
[ 0.000000] vmalloc : 0xc9000000 - 0xe0000000 ( 368 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8a00000 ( 138 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc04ac000 (4604 kB)
[ 0.000000] .data : 0xc04ac000 - 0xc04df7e0 ( 206 kB)
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:224
[ 0.000000] sched_clock: 32 bits at 72MHz, resolution 13ns, wraps every 59652ms
[ 0.000000] sched_clock: wrong multiply/shift: 1864135111>>27 vs calculated 3728270222>>28
[ 0.000000] sched_clock: fix multiply/shift to avoid scheduler hiccups
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.000594] Calibrating delay loop... 525.92 BogoMIPS (lpj=2629632)
[ 0.260138] pid_max: default: 32768 minimum: 301
[ 0.260566] Mount-cache hash table entries: 512
[ 0.261365] CPU: Testing write buffer coherency: ok
[ 0.268041] NET: Registered protocol family 16
[ 0.278968] Ambarella Coconut:
[ 0.279003] chip id: 5100
[ 0.279018] board type: 3
[ 0.279031] board revision: 10
[ 0.279044] chip name: a5m
[ 0.279057] HAL version: 176869
[ 0.279072] reference clock: 24000000
[ 0.279089] system configuration: 0x176804ea
[ 0.279107] boot type: 0x00000002
[ 0.279124] hif type: 0x00000000
[ 0.307387] bio: create slab <bio-0> at 0
[ 0.309962] ambarella-spi ambarella-spi.0: ambarella SPI Controller 0 created
[ 0.321103] ambarella-i2c ambarella-i2c.0: Ambarella Media Processor I2C adapter[i2c-0] probed!
[ 0.322678] ambarella-i2c ambarella-i2c.1: Ambarella Media Processor I2C adapter[i2c-1] probed!
[ 0.324124] i2c i2c-0: Added multiplexed i2c bus 2
[ 0.324166] ambarella-i2cmux ambarella-i2cmux.0: mux on ambarella-i2c adapter
[ 0.327116] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.331395] cfg80211: Calling CRDA to update world regulatory domain
[ 0.333086] Switching to clocksource ambarella-cs-timer
[ 0.340188] Switched to NOHz mode on CPU #0
[ 0.397242] NET: Registered protocol family 2
[ 0.397614] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.398550] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.398758] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.398901] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.398923] TCP reno registered
[ 0.398952] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.398996] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.399635] NET: Registered protocol family 1
[ 0.400559] RPC: Registered udp transport module.
[ 0.400596] RPC: Registered tcp transport module.
[ 0.400618] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.401137] Trying to unpack rootfs image as initramfs...
[ 0.403827] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 0.438145] Freeing initrd memory: 4096K
[ 0.441172] [ kernel version: svn-120249 ]
[ 0.441281] mmc0 power register success!
[ 0.441323] mmc1 power register success!
[ 0.441460] reboot times :1
[ 0.465031] msgmni has been set to 186
[ 0.473901] alg: No test for stdrng (krng)
[ 0.474071] io scheduler noop registered
[ 0.474101] io scheduler deadline registered
[ 0.474286] io scheduler cfq registered (default)
[ 0.478024] ambarella-fb ambarella-fb.0: probe p[720x480] v[720x576] c[1] b[0] l[736] @ [0xc5980000:0x00068000]!
[ 0.479888] ambarella-uart.0: ttyS0 at MMIO 0x70005000 (irq = 9) is a ambuart
[ 0.516451] brd: module loaded
[ 0.530936] loop: module loaded
[ 0.534539] NAND device: Manufacturer ID: 0x98, Chip ID: 0xd1 (Toshiba NAND 128MiB 3,3V 8-bit)
[ 0.534589] ambarella_nand_config_flash: 0x02e00140, 0x02c00140
[ 0.535025] Bad block table found at page 65472, version 0x01
[ 0.535557] Bad block table found at page 65408, version 0x01
[ 0.541428] ambarella-nand ambarella-nand: ambarella_nand_probe: Partition infomation found!
[ 0.541496] Creating 18 MTD partitions on "ambnand":
[ 0.541532] 0x000000000000-0x000000020000 : "bst"
[ 0.545748] 0x000000020000-0x000000120000 : "ptb"
[ 0.549546] 0x000000120000-0x000000220000 : "bld"
[ 0.553630] 0x000000220000-0x000000320000 : "hal"
[ 0.557549] 0x000000320000-0x000000420000 : "ano_ptb"
[ 0.561488] 0x000000420000-0x0000004a0000 : "env"
[ 0.565763] 0x0000004a0000-0x000000520000 : "param"
[ 0.569815] 0x000000520000-0x000000620000 : "dpt"
[ 0.574137] 0x000000620000-0x000001020000 : "rcvy"
[ 0.578355] 0x000001020000-0x000001820000 : "krn_pri"
[ 0.582260] 0x000001820000-0x000002020000 : "krn_sec"
[ 0.586490] 0x000002020000-0x000002420000 : "rmd_pri"
[ 0.590499] 0x000002420000-0x000002820000 : "rmd_sec"
[ 0.594838] 0x000002820000-0x000004020000 : "app_pri"
[ 0.598978] 0x000004020000-0x000005820000 : "app_sec"
[ 0.603448] 0x000005820000-0x000005c20000 : "cfg_pri"
[ 0.607617] 0x000005c20000-0x000006020000 : "cfg_sec"
[ 0.611946] 0x000006020000-0x000007020000 : "dbg"
[ 0.623489] PPP generic driver version 2.4.2
[ 0.624906] PPP Deflate Compression module registered
[ 0.624948] PPP BSD Compression module registered
[ 0.818501] Ambarella MII Bus: probed
[ 0.820192] ambarella-eth ambarella-eth.0: MAC Address[48:11:b2:25:e4:bb].
[ 0.820927] console [netcon0] enabled
[ 0.820956] netconsole: network logging started
[ 0.822629] mousedev: PS/2 mouse device common for all mice
[ 0.823843] input: AmbInput as /devices/virtual/input/input0
[ 0.824870] ambarella_gpio_irq_set_wake: irq[75] = girq[11] = 1
[ 0.824913] ambarella-input ambarella-input: AmbInput probed!
[ 0.825940] ambarella-adc ambarella-adc: ADC Host Controller [polling mode] probed!
[ 0.827632] ambarella-rtc ambarella-rtc: rtc core: registered ambarella-rtc as rtc0
[ 0.828227] i2c /dev entries driver
[ 0.833100] ambarella-wdt ambarella-wdt: Ambarella Media Processor Watch Dog Timer[ambarella-wdt].
[ 0.840003] ALSA device list:
[ 0.840037] No soundcards found.
[ 0.840223] Netfilter messages via NETLINK v0.30.
[ 0.840423] nf_conntrack version 0.5.0 (1488 buckets, 5952 max)
[ 0.841090] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.841265] TCP cubic registered
[ 0.841704] NET: Registered protocol family 10
[ 0.844725] Mobile IPv6
[ 0.844862] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 0.845126] IPv6 over IPv4 tunneling driver
[ 0.848955] NET: Registered protocol family 17
[ 0.849800] sctp: Hash tables configured (established 4096 bind 8192)
[ 0.850151] sctp: sctp_init_sock(sk: c58d6b20)
[ 0.850274] lib80211: common routines for IEEE802.11 drivers
[ 0.850308] lib80211_crypt: registered algorithm 'NULL'
[ 0.854627] ambarella-rtc ambarella-rtc: setting system clock to 2015-12-22 12:51:12 UTC (1450788672)
[ 0.855457] RAMDISK: gzip image found at block 0
[ 1.711120] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 1.711334] Freeing init memory: 148K
[ 3.739956] UBI: attaching mtd13 to ubi1
[ 3.739996] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.740019] UBI: logical eraseblock size: 129024 bytes
[ 3.740038] UBI: smallest flash I/O unit: 2048
[ 3.740055] UBI: sub-page size: 512
[ 3.740073] UBI: VID header offset: 512 (aligned 512)
[ 3.740093] UBI: data offset: 2048
[ 3.800373] UBI: max. sequence number: 448
[ 3.823363] UBI: attached mtd13 to ubi1
[ 3.823398] UBI: MTD device name: "app_pri"
[ 3.823420] UBI: MTD device size: 24 MiB
[ 3.823438] UBI: number of good PEBs: 192
[ 3.823454] UBI: number of bad PEBs: 0
[ 3.823470] UBI: number of corrupted PEBs: 0
[ 3.823486] UBI: max. allowed volumes: 128
[ 3.823502] UBI: wear-leveling threshold: 4096
[ 3.823518] UBI: number of internal volumes: 1
[ 3.823535] UBI: number of user volumes: 1
[ 3.823550] UBI: available PEBs: 0
[ 3.823566] UBI: total number of reserved PEBs: 192
[ 3.823583] UBI: number of PEBs reserved for bad PEB handling: 2
[ 3.823603] UBI: max/mean erase counter: 8/5
[ 3.823620] UBI: image sequence number: 1091856595
[ 3.831780] UBI: background thread "ubi_bgt1d" started, PID 625
[ 3.910392] UBIFS: recovery needed
[ 3.947207] UBIFS: recovery completed
[ 3.947255] UBIFS: mounted UBI device 1, volume 0, name "app_pri"
[ 3.947286] UBIFS: file system size: 22837248 bytes (22302 KiB, 21 MiB, 177 LEBs)
[ 3.947314] UBIFS: journal size: 1161216 bytes (1134 KiB, 1 MiB, 9 LEBs)
[ 3.947339] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.947358] UBIFS: default compressor: lzo
[ 3.947376] UBIFS: reserved for root: 1078659 bytes (1053 KiB)
[ 3.986192] UBI: attaching mtd15 to ubi3
[ 3.986234] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.986257] UBI: logical eraseblock size: 129024 bytes
[ 3.986276] UBI: smallest flash I/O unit: 2048
[ 3.986293] UBI: sub-page size: 512
[ 3.986311] UBI: VID header offset: 512 (aligned 512)
[ 3.986329] UBI: data offset: 2048
[ 3.995016] UBI: max. sequence number: 133
[ 4.018500] UBI: attached mtd15 to ubi3
[ 4.018532] UBI: MTD device name: "cfg_pri"
[ 4.018557] UBI: MTD device size: 4 MiB
[ 4.018574] UBI: number of good PEBs: 32
[ 4.018590] UBI: number of bad PEBs: 0
[ 4.018606] UBI: number of corrupted PEBs: 0
[ 4.018622] UBI: max. allowed volumes: 128
[ 4.018638] UBI: wear-leveling threshold: 4096
[ 4.018654] UBI: number of internal volumes: 1
[ 4.018669] UBI: number of user volumes: 1
[ 4.018685] UBI: available PEBs: 0
[ 4.018701] UBI: total number of reserved PEBs: 32
[ 4.018718] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.018738] UBI: max/mean erase counter: 15/12
[ 4.018755] UBI: image sequence number: 1151186759
[ 4.023304] UBI: background thread "ubi_bgt3d" started, PID 634
[ 4.101821] UBIFS: recovery needed
[ 4.151235] UBIFS: recovery completed
[ 4.151284] UBIFS: mounted UBI device 3, volume 0, name "cfg_pri"
[ 4.151312] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEBs)
[ 4.151340] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs)
[ 4.151364] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.151385] UBIFS: default compressor: lzo
[ 4.151402] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.290810] UBI: attaching mtd16 to ubi4
[ 4.290852] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 4.290876] UBI: logical eraseblock size: 129024 bytes
[ 4.290896] UBI: smallest flash I/O unit: 2048
[ 4.290914] UBI: sub-page size: 512
[ 4.290932] UBI: VID header offset: 512 (aligned 512)
[ 4.290951] UBI: data offset: 2048
[ 4.299639] UBI: max. sequence number: 137
[ 4.323725] UBI: attached mtd16 to ubi4
[ 4.323759] UBI: MTD device name: "cfg_sec"
[ 4.323781] UBI: MTD device size: 4 MiB
[ 4.323799] UBI: number of good PEBs: 32
[ 4.323815] UBI: number of bad PEBs: 0
[ 4.323831] UBI: number of corrupted PEBs: 0
[ 4.323846] UBI: max. allowed volumes: 128
[ 4.323863] UBI: wear-leveling threshold: 4096
[ 4.323879] UBI: number of internal volumes: 1
[ 4.323895] UBI: number of user volumes: 1
[ 4.323911] UBI: available PEBs: 0
[ 4.323927] UBI: total number of reserved PEBs: 32
[ 4.323944] UBI: number of PEBs reserved for bad PEB handling: 2
[ 4.323964] UBI: max/mean erase counter: 15/12
[ 4.323980] UBI: image sequence number: 589690876
[ 4.332067] UBI: background thread "ubi_bgt4d" started, PID 644
[ 4.406920] UBIFS: recovery needed
[ 4.480553] UBIFS: recovery completed
[ 4.480601] UBIFS: mounted UBI device 4, volume 0, name "cfg_sec"
[ 4.480630] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEBs)
[ 4.480658] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs)
[ 4.480684] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 4.480703] UBIFS: default compressor: lzo
[ 4.480721] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 4.690233] net eth0: Could not find default PHY in 9.
[ 4.690277] net eth0: Try PHY[9] whose id is 0x00008201!
[ 4.691495] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.683568] PHY: 0:09 - Link is Up - 100/Full
[ 6.683783] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.521711] dsp: module license 'Proprietary' taints kernel.
[ 8.521751] Disabling lock debugging due to kernel taint
[ 8.601193] img: aaa_fifo2_base malloc c5b50000
[ 9.022740] >>>>>> DSP LOG ADDR START PHY 0xc0080000
[ 9.022774] Init software HR timer for DSP communication
[ 9.052843] cdev_init rs485_fops ...
[ 9.052895] adding uart1, minor = 0
[ 9.056583] Successfully insmod uart232 module!
[ 9.200845] amba_debug_init 248:248.
[ 17.523236] eth0: no IPv6 routers present
[ 34.003895] AMBARELLA SoC Audio DUMMY Codec
[ 34.005413] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok
[ 34.877350] MT9T002 sensor ID is 0x2604
[ 34.931498] CMEMK module: built on Aug 23 2012 at 17:05:43
[ 34.931545] Reference Linux version 2.6.38
[ 34.931564] File /mnt/data_bsp/data_yuhuanhuan/raptor/a5s_svn2/kernel/hik_drivers/cmem/src/module/cmemk.c
[ 34.939169] cmemk initialized
[ 47.986243] iav error: Failed to wait for completion!
[ 48.081419] iav error: Failed to wait for completion!

now here is the ssh output from the 4th working camera,

# dmesg
[ 0.000000] Linux version 2.6.38.8 (root@HIK-RD-CI-Frontend) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-70) )
[ 0.000000] #33 PREEMPT Fri Oct 24 10:46:55 CST 2014
[ 0.000000] CPU: ARMv6-compatible processor [4117b365] revision 5 (ARMv6TEJ), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Coconut
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Ambarella: AHB = 0x60000000[0xf0000000],0x01000000 0
[ 0.000000] Ambarella: APB = 0x70000000[0xf1000000],0x01000000 0
[ 0.000000] Ambarella: PPM = 0xc0000000[0xe0000000],0x00200000 9
[ 0.000000] Ambarella: BSB = 0xc8c00000[0xe8c00000],0x00400000 9
[ 0.000000] Ambarella: DSP = 0xc9000000[0xe9000000],0x07000000 9
[ 0.000000] Ambarella: HAL = 0xc00a0000[0xfee00000],0x0000e708 9
[ 0.000000] On node 0 totalpages: 25344
[ 0.000000] free_area_init_node: node 0, pgdat c04dd028, node_mem_map c0503000
[ 0.000000] Normal zone: 198 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 25146 pages, LIFO batch:7
[ 0.000000] bootmem_init: high_memory = 0xc8a00000
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 25146
[ 0.000000] Kernel command line: console=ttyS0 initrd=0xc0a00000,0x400000 rw root=/dev/ram dbg=0 KRN_PRT=pri RMD_PRT=pri reserved=0xc6500000,0x100000,99 video=amb0fb:720x480,720x480,1,0
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 99MB = 99MB total
[ 0.000000] Memory: 91192k/91192k available, 10184k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfe600000 - 0xfee00000 ( 8 MB)
[ 0.000000] vmalloc : 0xc9000000 - 0xe0000000 ( 368 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8a00000 ( 138 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)
[ 0.000000] .text : 0xc002d000 - 0xc04aa000 (4596 kB)
[ 0.000000] .data : 0xc04aa000 - 0xc04dd6e0 ( 206 kB)
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:224
[ 0.000000] sched_clock: 32 bits at 72MHz, resolution 13ns, wraps every 59652ms
[ 0.000000] sched_clock: wrong multiply/shift: 1864135111>>27 vs calculated 3728270222>>28
[ 0.000000] sched_clock: fix multiply/shift to avoid scheduler hiccups
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS0] enabled
[ 0.000599] Calibrating delay loop... 525.92 BogoMIPS (lpj=2629632)
[ 0.260143] pid_max: default: 32768 minimum: 301
[ 0.260568] Mount-cache hash table entries: 512
[ 0.261372] CPU: Testing write buffer coherency: ok
[ 0.268096] NET: Registered protocol family 16
[ 0.279073] Ambarella Coconut:
[ 0.279108] chip id: 5100
[ 0.279122] board type: 3
[ 0.279136] board revision: 10
[ 0.279149] chip name: a5m
[ 0.279162] HAL version: 176869
[ 0.279179] reference clock: 24000000
[ 0.279197] system configuration: 0x177804ea
[ 0.279214] boot type: 0x00000002
[ 0.279229] hif type: 0x00000000
[ 0.307492] bio: create slab <bio-0> at 0
[ 0.310056] ambarella-spi ambarella-spi.0: ambarella SPI Controller 0 created
[ 0.321212] ambarella-i2c ambarella-i2c.0: Ambarella Media Processor I2C adapter[i2c-0] probed!
[ 0.322787] ambarella-i2c ambarella-i2c.1: Ambarella Media Processor I2C adapter[i2c-1] probed!
[ 0.324242] i2c i2c-0: Added multiplexed i2c bus 2
[ 0.324285] ambarella-i2cmux ambarella-i2cmux.0: mux on ambarella-i2c adapter
[ 0.327264] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.331580] cfg80211: Calling CRDA to update world regulatory domain
[ 0.333263] Switching to clocksource ambarella-cs-timer
[ 0.340192] Switched to NOHz mode on CPU #0
[ 0.397509] NET: Registered protocol family 2
[ 0.397872] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.398779] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.398986] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.399133] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.399156] TCP reno registered
[ 0.399185] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.399231] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.399877] NET: Registered protocol family 1
[ 0.400807] RPC: Registered udp transport module.
[ 0.400845] RPC: Registered tcp transport module.
[ 0.400865] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.401375] Trying to unpack rootfs image as initramfs...
[ 0.404035] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 0.438709] Freeing initrd memory: 4096K
[ 0.441745] [ kernel version: svn-97978 ]
[ 0.441851] mmc0 power register success!
[ 0.441893] mmc1 power register success!
[ 0.442032] reboot times :1
[ 0.465172] msgmni has been set to 186
[ 0.473869] alg: No test for stdrng (krng)
[ 0.474030] io scheduler noop registered
[ 0.474059] io scheduler deadline registered
[ 0.474236] io scheduler cfq registered (default)
[ 0.477988] ambarella-fb ambarella-fb.0: probe p[720x480] v[720x576] c[1] b[0] l[736] @ [0xc5980000:0x00068000]!
[ 0.479850] ambarella-uart.0: ttyS0 at MMIO 0x70005000 (irq = 9) is a ambuart
[ 0.516624] brd: module loaded
[ 0.531150] loop: module loaded
[ 0.534754] NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
[ 0.534800] ambarella_nand_config_flash: 0x02e00140, 0x02c00140
[ 0.535227] Bad block table found at page 65472, version 0x01
[ 0.535762] Bad block table found at page 65408, version 0x01
[ 0.536072] nand_read_bbt: Bad block at 0x0000037e0000
[ 0.541724] ambarella-nand ambarella-nand: ambarella_nand_probe: Partition infomation found!
[ 0.541789] Creating 18 MTD partitions on "ambnand":
[ 0.541826] 0x000000000000-0x000000020000 : "bst"
[ 0.546037] 0x000000020000-0x000000120000 : "ptb"
[ 0.549854] 0x000000120000-0x000000220000 : "bld"
[ 0.553966] 0x000000220000-0x000000320000 : "hal"
[ 0.557860] 0x000000320000-0x000000420000 : "ano_ptb"
[ 0.561791] 0x000000420000-0x0000004a0000 : "env"
[ 0.566074] 0x0000004a0000-0x000000520000 : "param"
[ 0.570084] 0x000000520000-0x000000620000 : "dpt"
[ 0.574424] 0x000000620000-0x000001020000 : "rcvy"
[ 0.578638] 0x000001020000-0x000001820000 : "krn_pri"
[ 0.582554] 0x000001820000-0x000002020000 : "krn_sec"
[ 0.586782] 0x000002020000-0x000002420000 : "rmd_pri"
[ 0.590778] 0x000002420000-0x000002820000 : "rmd_sec"
[ 0.595098] 0x000002820000-0x000004020000 : "app_pri"
[ 0.599266] 0x000004020000-0x000005820000 : "app_sec"
[ 0.603741] 0x000005820000-0x000005c20000 : "cfg_pri"
[ 0.607892] 0x000005c20000-0x000006020000 : "cfg_sec"
[ 0.612201] 0x000006020000-0x000007020000 : "dbg"
[ 0.623819] PPP generic driver version 2.4.2
[ 0.625244] PPP Deflate Compression module registered
[ 0.625286] PPP BSD Compression module registered
[ 0.818674] Ambarella MII Bus: probed
[ 0.820345] ambarella-eth ambarella-eth.0: MAC Address[c0:56:e3:fb:b9:ad].
[ 0.821085] console [netcon0] enabled
[ 0.821113] netconsole: network logging started
[ 0.822791] mousedev: PS/2 mouse device common for all mice
[ 0.824017] input: AmbInput as /devices/virtual/input/input0
[ 0.825053] ambarella_gpio_irq_set_wake: irq[75] = girq[11] = 1
[ 0.825097] ambarella-input ambarella-input: AmbInput probed!
[ 0.826132] ambarella-adc ambarella-adc: ADC Host Controller [polling mode] probed!
[ 0.827840] ambarella-rtc ambarella-rtc: rtc core: registered ambarella-rtc as rtc0
[ 0.828432] i2c /dev entries driver
[ 0.833522] ambarella-wdt ambarella-wdt: Ambarella Media Processor Watch Dog Timer[ambarella-wdt].
[ 0.840222] ALSA device list:
[ 0.840255] No soundcards found.
[ 0.840438] Netfilter messages via NETLINK v0.30.
[ 0.840655] nf_conntrack version 0.5.0 (1488 buckets, 5952 max)
[ 0.841331] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.841508] TCP cubic registered
[ 0.841942] NET: Registered protocol family 10
[ 0.844937] Mobile IPv6
[ 0.845072] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 0.845331] IPv6 over IPv4 tunneling driver
[ 0.849165] NET: Registered protocol family 17
[ 0.850004] sctp: Hash tables configured (established 4096 bind 8192)
[ 0.850351] sctp: sctp_init_sock(sk: c58d6b20)
[ 0.850473] lib80211: common routines for IEEE802.11 drivers
[ 0.850508] lib80211_crypt: registered algorithm 'NULL'
[ 0.854843] ambarella-rtc ambarella-rtc: setting system clock to 2015-12-22 12:48:34 UTC (1450788514)
[ 0.855678] RAMDISK: gzip image found at block 0
[ 1.672432] EXT2-fs (ram0): warning: maximal mount count reached, running e2fsck is recommended
[ 1.672623] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 1.672834] Freeing init memory: 148K
[ 3.701438] UBI: attaching mtd13 to ubi1
[ 3.701480] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 3.701505] UBI: logical eraseblock size: 129024 bytes
[ 3.701524] UBI: smallest flash I/O unit: 2048
[ 3.701541] UBI: sub-page size: 512
[ 3.701559] UBI: VID header offset: 512 (aligned 512)
[ 3.701579] UBI: data offset: 2048
[ 3.760149] UBI: max. sequence number: 184
[ 3.785558] UBI: attached mtd13 to ubi1
[ 3.785591] UBI: MTD device name: "app_pri"
[ 3.785612] UBI: MTD device size: 24 MiB
[ 3.785631] UBI: number of good PEBs: 191
[ 3.785647] UBI: number of bad PEBs: 1
[ 3.785663] UBI: number of corrupted PEBs: 0
[ 3.785679] UBI: max. allowed volumes: 128
[ 3.785695] UBI: wear-leveling threshold: 4096
[ 3.785712] UBI: number of internal volumes: 1
[ 3.785728] UBI: number of user volumes: 1
[ 3.785743] UBI: available PEBs: 0
[ 3.785759] UBI: total number of reserved PEBs: 191
[ 3.785777] UBI: number of PEBs reserved for bad PEB handling: 2
[ 3.785798] UBI: max/mean erase counter: 12/6
[ 3.785814] UBI: image sequence number: 738098785
[ 3.794019] UBI: background thread "ubi_bgt1d" started, PID 627
[ 3.868633] UBIFS: recovery needed
[ 3.899664] UBIFS: recovery completed
[ 3.899711] UBIFS: mounted UBI device 1, volume 0, name "app_pri"
[ 3.899741] UBIFS: file system size: 22708224 bytes (22176 KiB, 21 MiB, 176 LEBs)
[ 3.899768] UBIFS: journal size: 1161216 bytes (1134 KiB, 1 MiB, 9 LEBs)
[ 3.899793] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 3.899811] UBIFS: default compressor: lzo
[ 3.899829] UBIFS: reserved for root: 1072565 bytes (1047 KiB)
[ 6.442644] UBI: attaching mtd15 to ubi3
[ 6.442687] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 6.442714] UBI: logical eraseblock size: 129024 bytes
[ 6.442733] UBI: smallest flash I/O unit: 2048
[ 6.442751] UBI: sub-page size: 512
[ 6.442770] UBI: VID header offset: 512 (aligned 512)
[ 6.442790] UBI: data offset: 2048
[ 6.451550] UBI: max. sequence number: 105
[ 6.475632] UBI: attached mtd15 to ubi3
[ 6.475665] UBI: MTD device name: "cfg_pri"
[ 6.475687] UBI: MTD device size: 4 MiB
[ 6.475704] UBI: number of good PEBs: 32
[ 6.475720] UBI: number of bad PEBs: 0
[ 6.475736] UBI: number of corrupted PEBs: 0
[ 6.475752] UBI: max. allowed volumes: 128
[ 6.475768] UBI: wear-leveling threshold: 4096
[ 6.475785] UBI: number of internal volumes: 1
[ 6.475800] UBI: number of user volumes: 1
[ 6.475816] UBI: available PEBs: 0
[ 6.475832] UBI: total number of reserved PEBs: 32
[ 6.475850] UBI: number of PEBs reserved for bad PEB handling: 2
[ 6.475871] UBI: max/mean erase counter: 18/16
[ 6.475888] UBI: image sequence number: 1922621179
[ 6.484035] UBI: background thread "ubi_bgt3d" started, PID 637
[ 6.558702] UBIFS: recovery needed
[ 6.585954] UBIFS: recovery completed
[ 6.586001] UBIFS: mounted UBI device 3, volume 0, name "cfg_pri"
[ 6.586029] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEBs)
[ 6.586057] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs)
[ 6.586081] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 6.586100] UBIFS: default compressor: lzo
[ 6.586118] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 6.689040] UBI: attaching mtd16 to ubi4
[ 6.689081] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 6.689105] UBI: logical eraseblock size: 129024 bytes
[ 6.689125] UBI: smallest flash I/O unit: 2048
[ 6.689142] UBI: sub-page size: 512
[ 6.689161] UBI: VID header offset: 512 (aligned 512)
[ 6.689182] UBI: data offset: 2048
[ 6.697962] UBI: max. sequence number: 110
[ 6.721316] UBI: attached mtd16 to ubi4
[ 6.721350] UBI: MTD device name: "cfg_sec"
[ 6.721370] UBI: MTD device size: 4 MiB
[ 6.721388] UBI: number of good PEBs: 32
[ 6.721404] UBI: number of bad PEBs: 0
[ 6.721420] UBI: number of corrupted PEBs: 0
[ 6.721435] UBI: max. allowed volumes: 128
[ 6.721452] UBI: wear-leveling threshold: 4096
[ 6.721469] UBI: number of internal volumes: 1
[ 6.721484] UBI: number of user volumes: 1
[ 6.721500] UBI: available PEBs: 0
[ 6.721517] UBI: total number of reserved PEBs: 32
[ 6.721534] UBI: number of PEBs reserved for bad PEB handling: 2
[ 6.721555] UBI: max/mean erase counter: 18/16
[ 6.721571] UBI: image sequence number: 894428365
[ 6.723482] UBI: background thread "ubi_bgt4d" started, PID 648
[ 6.804747] UBIFS: recovery needed
[ 6.871138] UBIFS: recovery completed
[ 6.871184] UBIFS: mounted UBI device 4, volume 0, name "cfg_sec"
[ 6.871211] UBIFS: file system size: 2193408 bytes (2142 KiB, 2 MiB, 17 LEBs)
[ 6.871239] UBIFS: journal size: 1032193 bytes (1008 KiB, 0 MiB, 6 LEBs)
[ 6.871264] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 6.871283] UBIFS: default compressor: lzo
[ 6.871301] UBIFS: reserved for root: 103599 bytes (101 KiB)
[ 8.046638] net eth0: Could not find default PHY in 9.
[ 8.046680] net eth0: Try PHY[9] whose id is 0x00008201!
[ 8.047899] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.043890] PHY: 0:09 - Link is Up - 100/Full
[ 10.044103] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 16.127198] dsp: module license 'Proprietary' taints kernel.
[ 16.127237] Disabling lock debugging due to kernel taint
[ 16.206029] img: aaa_fifo2_base malloc c2840000
[ 16.625428] >>>>>> DSP LOG ADDR START PHY 0xc0080000
[ 16.625463] Init software HR timer for DSP communication
[ 16.655366] cdev_init rs485_fops ...
[ 16.655418] adding uart1, minor = 0
[ 16.658960] Successfully insmod uart232 module!
[ 16.800684] amba_debug_init 248:248.
[ 20.843356] eth0: no IPv6 routers present
[ 32.883598] ak4954 i2c probe
[ 32.883837] ak4954 mode init
[ 32.921853] ak4954-codec 0-0012: AK4954 Audio Codec 0.1AK4954 probe
[ 32.922054] ambarella-i2c ambarella-i2c.0: ambarella_i2c_stop[2] from 1 to 9
[ 32.922219] ambarella-i2c ambarella-i2c.0: ambarella_i2c_irq in wrong state[0x9]
[ 32.922259] ambarella-i2c ambarella-i2c.0: status_reg[0x40]
[ 32.922282] ambarella-i2c ambarella-i2c.0: control_reg[0x3]
[ 33.913432] ambarella-i2c ambarella-i2c.0: No ACK from address 0x24, 0:0!
[ 33.913477] ambarella-i2c ambarella-i2c.0: I2C state 0x9, please check address 0x24!
[ 33.973417] <ak4954_probe>audio codec's ID = 177
[ 34.000271] audio codec AK4951 initialized!
[ 34.001835] asoc: ak4954-hifi <-> ambarella-i2s.0 mapping ok
[ 34.273724] <ak4954_set_in_volum>set device_id success!
[ 34.273764] AK4954:set input volum 50
[ 34.394987] ========== SD Driver Build Date: May 16 2014, Time: 17:18:21 ==========
[ 34.395190] SD card slot0, card detect mode:soft poll
[ 34.395433] ambarella-sd ambarella-sd.0: Slot0 use bounce buffer[0xc26e0000<->0xc28e0000]
[ 34.395475] ambarella-sd ambarella-sd.0: Slot0 req_size=131072, segs=32, seg_size=131072
[ 34.395646] ambarella-sd ambarella-sd.0: Slot1 use bounce buffer[0xc21c0000<->0xc23c0000]
[ 34.395683] ambarella-sd ambarella-sd.0: Slot1 req_size=131072, segs=32, seg_size=131072
[ 34.473508] ambarella-sd ambarella-sd.0: Ambarella SD/MMC[0] probed 2 slots, 0x09e130b0!
[ 34.973534] mmc0: new high speed SDHC card at address aaaa
[ 34.985163] mmcblk0: mmc0:aaaa SL64G 59.4 GiB
[ 35.001709] mmcblk0: p1
[ 35.166423] MT9T002 sensor ID is 0x2604
[ 35.216786] CMEMK module: built on Aug 23 2012 at 17:05:43
[ 35.216834] Reference Linux version 2.6.38
[ 35.216853] File /mnt/data_bsp/data_yuhuanhuan/raptor/a5s_svn2/kernel/hik_drivers/cmem/src/module/cmemk.c
[ 35.224545] cmemk initialized
[ 37.983834] set audio rates 8000Hz
[ 38.063579] set audio rates 8000Hz
[ 43.163704] mmc0: card aaaa removed
[ 45.453870] iav error: Failed to wait for completion!
[ 45.542476] iav error: Failed to wait for completion!
[ 46.574011] mmc0: new high speed SDHC card at address aaaa
[ 46.589703] mmcblk0: mmc0:aaaa SL64G 59.4 GiB
[ 46.608025] mmcblk0: p1

Can see the SD card bits in the working one!

 

[Click4]

Just run the 2 through a file comparer...mostly the same right up until the end,

the working camera has this big block,

[ 32.883598] ak4954 i2c probe
[ 34.931498] CMEMK module: built on Aug 23 2012 at 17:05:43 [ 32.883837] ak4954 mode init
[ 34.931545] Reference Linux version 2.6.38 [ 32.921853] ak4954-codec 0-0012: AK4954 Audio Codec 0.1AK4954 probe
[ 34.931564] File /mnt/data_bsp/data_yuhuanhuan/raptor/a5s_svn2/kernel/hik_drivers/cmem/src/module/cmemk.c [ 32.922054] ambarella-i2c ambarella-i2c.0: ambarella_i2c_stop[2] from 1 to 9
[ 34.939169] cmemk initialized [ 32.922219] ambarella-i2c ambarella-i2c.0: ambarella_i2c_irq in wrong state[0x9]
[ 47.986243] iav error: Failed to wait for completion! [ 32.922259] ambarella-i2c ambarella-i2c.0: status_reg[0x40]
[ 48.081419] iav error: Failed to wait for completion! [ 32.922282] ambarella-i2c ambarella-i2c.0: control_reg[0x3]
[ 33.913432] ambarella-i2c ambarella-i2c.0: No ACK from address 0x24, 0:0!
[ 33.913477] ambarella-i2c ambarella-i2c.0: I2C state 0x9, please check address 0x24!
[ 33.973417] <ak4954_probe>audio codec's ID = 177
[ 34.000271] audio codec AK4951 initialized!
[ 34.001835] asoc: ak4954-hifi <-> ambarella-i2s.0 mapping ok
[ 34.273724] <ak4954_set_in_volum>set device_id success!
[ 34.273764] AK4954:set input volum 50
[ 34.394987] ========== SD Driver Build Date: May 16 2014, Time: 17:18:21 ==========
[ 34.395190] SD card slot0, card detect mode:soft poll
[ 34.395433] ambarella-sd ambarella-sd.0: Slot0 use bounce buffer[0xc26e0000<->0xc28e0000]
[ 34.395475] ambarella-sd ambarella-sd.0: Slot0 req_size=131072, segs=32, seg_size=131072
[ 34.395646] ambarella-sd ambarella-sd.0: Slot1 use bounce buffer[0xc21c0000<->0xc23c0000]
[ 34.395683] ambarella-sd ambarella-sd.0: Slot1 req_size=131072, segs=32, seg_size=131072
[ 34.473508] ambarella-sd ambarella-sd.0: Ambarella SD/MMC[0] probed 2 slots, 0x09e130b0!
[ 34.973534] mmc0: new high speed SDHC card at address aaaa
[ 34.985163] mmcblk0: mmc0:aaaa SL64G 59.4 GiB
[ 35.001709] mmcblk0: p1

[ 46.574011] mmc0: new high speed SDHC card at address aaaa
[ 46.589703] mmcblk0: mmc0:aaaa SL64G 59.4 GiB
[ 46.608025] mmcblk0: p1

whereas the defective camera only has these 3 lines in same place,

[ 34.003895] AMBARELLA SoC Audio DUMMY Codec [ 16.800684] amba_debug_init 248:248.
[ 34.005413] asoc: AMBARELLA_DUMMY_CODEC <-> ambarella-i2s.0 mapping ok

 

[alastairstevenson]

Yes indeed, the log from the working camera has plenty of audio and SD positive completions.

 

[Click4]

Yep, sorry about slow reply.

I am now being told to get my money back I have to send back the 3 defective cameras, and 2 working ones as well.

Just a thought, but is there anything I can do with SSH access on the World Region cameras I have before I send them back that I maybe able to use on China region cameras to make them World Region also? Like clone anything across which determines the region? Seeming I have both World Region and China Region cameras at the moment, before I send them back.

Thanks

 

[Enabler]

If I understand what you said correctly the World region cameras don't even have the components on the PCB ?

 

[Click4]

If I understand what you said correctly the World region cameras don't even have the components on the PCB ?

I have 3 world region cameras, and 1 China region camera of dome type.

china region one works fine, all features work.
world region one doesn't work, lots of features like audio, alarm, SD, auto iris non functional despite having cabling on device for them and sd card slot.

did above output, and it appears world region ones are missing components from PCB for whatever reason because things like audio, on world region ones it just loads a dummy driver, and nothing for SD, but on China region ones they load fine. Can't physically check without pulling camera apart and not doing that as they have to go back.
but from ssh output it appears that way

so possibly reject batch of mis-manufacturer with wrong PCB. No idea.

they are t fake because they had 5.3 installed on them when I purchased them.

and it's more than just. Faulty unit because all 3 world region ones have same problem.

 

[Enabler]

Oh in that case probably not missing components.

Tried factory configuration reset in web page? Or maybe changing to latest firmware?

 

[Enabler]

Also any chance of a prtHardInfo (in ssh) from one of the cameras that doesn't work ok?

 

[Click4]

Hi,

yep tried a default reset, can't update to newer firmware, it was sent to me with latest firmware already, I checked.

Will try other bit in SSH now.

i don't know if it's missing components or not as I can't see underside of PCB was just going by the previous ssh output. Top side looks complete.

but something not right on the 3 world region ones, because with a sd card in it, it won't even show up, below serial number on config pages it shows 0,0,0,0 for audio in, audio out, alarm, and hdd.

go to video and audio tab, no audio tab for audio options, go to video drop down under video, just says video, no video and audio option, go to Storage, no SD card shows, go to exposure under image and no auto iris option in drop down, only manual.

its same on all 3 world region ones, has the SD card slot inside though, and the extra wire with audio and alarm connections.


the China region one has identical wires and sd socket and recognises everything fine.

 

[Click4]

Working Camera - China Region

# prtHardInfo
Start at 2015-12-27 20:35:43
Serial NO S-2CD2732F-IS20150201CCCH501694789
V5.2.5 build 141201
hardwareVersion = 0x0
hardWareExtVersion = 0x0
encodeChans = 1
decodeChans = 1
alarmInNums = 1
alarmOutNums = 1
ataCtrlNums = 0
flashChipNums = 0
ramSize = 0x4000000
networksNums = 1
language = 1
devType = 38926
net reboot count = 0
SD status = 0 (1:noraml;0:none)
Path: .
Working Copy Root Path: /data1/data_liwenwei/work/frontend_software_platform_5.2 .7_R0
URL: https://192.0.0.140/Camera/Platform/Branches/branches_frontend_software_pla tform/frontend_software_platform_5.2.7_R0
Repository Root: https://192.0.0.140/Camera
Repository UUID: df2d70c3-7593-7941-af1e-571b313c0946
Revision: 103727
Node Kind: directory
Schedule: normal
Last Changed Author: liwenwei
Last Changed Rev: 103727
Last Changed Date: 2014-12-01 20:51:32 +0800 (Mon, 01 Dec 2014)

Non Working World Region camera

# prtHardInfo
Start at 2015-12-27 20:40:23
Serial NO S-2CD2732F-IS20150317CCWR321364435
V5.3.0 build 150814
NetProcess Version: 1.4.0 [20:10:19-Mar 10 2015]
Db Encrypt Version: 65537
hardwareVersion = 0x0
hardWareExtVersion = 0x0
encodeChans = 1
decodeChans = 1
alarmInNums = 0
alarmOutNums = 0
ataCtrlNums = 0
flashChipNums = 0
ramSize = 0x4000000
networksNums = 1
language = 1
devType = 0x9808
net reboot count = 0
Path: .
Working Copy Root Path: /usr/local/jenkins/workspace/Frontend_BaseLine_Publish_Build/2015-08-14_21-06-22
URL: https://192.0.0.140/Camera/Platform/Branches/branches_frontend_software_platform/IPC_develop_branch/ipc_plateform_5.3.0
Repository Root: https://192.0.0.140/Camera
Repository UUID: df2d70c3-7593-7941-af1e-571b313c0946
Revision: 143849
Node Kind: directory
Schedule: normal
Last Changed Author: zhoujiafeng
Last Changed Rev: 143290
Last Changed Date: 2015-08-12 19:24:53 +0800 (Wed, 12 Aug 2015)

 

[Enabler]

devType = 0x9808

hmm - that's different to the one above and mine

devType = 38926

which is 0x980E

I'm not sure your non working is really a DS-2CD2732F-IS

 

[Enabler]

I think 0x9808 is DS-2CD2332-I

(no S or F)

So the model name and devtype don't match. One (or both) of them is incorrect which is why you are having the problems.

Does the camera have an SD card slot (remove the dome - shouldn't cause a problem returning it)?

If yes then the devtype is wrong.
If no then the model name is wrong.

Edit:

oh your post above says it DOES have SD card. In that case the dev type is wrong - this is set in the flash so not clear why it would be incorrect unless the seller changed it for some reason or I suppose faulty from Hikvision (unlikely in my opinion).

 

[Click4]

hmm - that's different to the one above and mine



which is 0x980E

I'm not sure your non working is really a DS-2CD2732F-IS

Hi,

Thanks for reply,

To be honest I have no idea what it is,

I know what it should be and what I ordered lol DS-2CD2732F-IS

It looks like one, it reports as one.

But I can't figure out if it's a fake, a reject or something else.

It has the latest firmware on it, which was something I thought couldn't be installed on Chinese ones... Which made me think twice about it being a fake.

But aside from that I'm clueless, all I know is it has an sd card slot, but doesn't recognise sd card or even list it on the ssh outputs.

It has alarm input, output wiring and audio... But again nothing functional.

It does have an SD slot yep, I've had SD cards in it.

And board looks same as the working one.

If it's got wrong model number programmed into itX why is it still reporting correct model number?