Hikvision DS-2CD2132F-IS FPS Low

J

jaredtizzle

Young grasshopper
Mar 27, 2016
32
0
I've done some searching, and I can't seem to figure out why my dome camera is stuck ~1-2fps

Below are my settings
[TABLE="class: deviceinfotable"]
[TR]
[TD="class: rowheader deviceinfotd"]Firmware Version[/TD]
[TD="class: deviceinfotd"]V5.2.5 build 141201[/TD]
[/TR]
[TR]
[TD="class: rowheader deviceinfotd"]Encoding Version[/TD]
[TD="class: deviceinfotd"]V5.0 build 140714[/TD]
[/TR]
[/TABLE]
The cameras are connected to a Cisco 2960S through an 8 port POE injector. (All Cat5E)
The switchports are hardset to 100/full. The runs are a max on 150ft.
Connection from my switch to BI pc is Cat6 running at 1000/full.
GB8ikki.jpg
0keXPqo.png
3jcQFIo.png
iueTTW2.png


Thank you for any help you can provide!


Edit:
I should add, I'm seeing a large quantity of errors on the port for this camera
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Fa0/1 0 37 0 37 0
Fa0/2 0 567 0 567 0
Fa0/3 0 101486 0 101770 0
Fa0/4 0 0 0 0 0
 
Last edited by a moderator:
It looks ok, Much better than in blue iris. I don't know if there is a way to directly view frame rate in browser. I can still notice occasional hangups though.

My other camera (Cheap 30$ Hosafe) has 30fps in BI and no stutter ever.
 
jaredtizzle said:
It looks ok, Much better than in blue iris. I don't know if there is a way to directly view frame rate in browser. I can still notice occasional hangups though.

My other camera (Cheap 30$ Hosafe) has 30fps in BI and no stutter ever.
Click to expand...
Disable all other cameras in BI and test. The demo mode seems to cut fps..I have seen this on a few installs, as soon as I enter the key the frame rate goes up.
 
Even using ONVIF, I get "No Signal" 5-6 times a minute. I'm wondering if i possibly have a bad termination on that cable...
 
jaredtizzle said:
Even using ONVIF, I get "No Signal" 5-6 times a minute. I'm wondering if i possibly have a bad termination on that cable...
Click to expand...
That is very probable. What kind of cable are you using? brand? Copper or copper clad aluminium (CCA) did you wire using 568 standards?
 
I haven't wired up my house with CAT6 yet and my server is inside, so I setup two wireless routers to act as a dedicated bridge between garage and house. When the connection would get weaker, I'd see the same behavior you're describing - not enough frames reaching BI. It was an issue with connectivity between camera and server.

I'd also recommend checking the cable as suggested above.
 
Odd situation... When I add a 2nd Hikvision Camera (DS-2CD2632F-IS), both cameras have extreme frame drop and almost always lose connectivity. I've ruled out the POE device by connecting the new camera to a separate POE injector. I also re-ran the cable for the original dome camera. Any ideas?
 
It seems like there is interference... Even in this screenshot you can see my Front Door camera show up where the front corner should be..I'd rather not sit in wireshark for 3 hours, anybody have any clue what is happening?
IP Address of the dome camera is 192.168.1.11, the new bullet is 192.168.1.12
 

Attachments

  • x6oCm38.png
    x6oCm38.png
    366.5 KB · Views: 11
I've done that twice already. Disabled that setting, frame rates are low again on the camera with that disabled. :(
ieOfWIB.jpg
 
You must log in or register to reply here.
Top Bottom