JACK to send the latest upgrade file.

  • Like
Reactions: cuistots
Jack sent updates for my camera.

thanks @nikifon
I see that this latest firmware has been resolved recording on SD card.
register now well on the sd card.
Latest firmware for V2 as of IPNC_S2l2._build20170314. Upgrade at your own risk.
and for S2l2 for v2 only.
 

Attachments

  • new for v2.PNG
    new for v2.PNG
    34.7 KB · Views: 140
Hi Guys, have the same issue with micro SD card on YC-110AR cam from Jack.
@vasycara - could you plz share this firmware somewere plz?

Right now I have these below:
Program Version V2.1.1 Build 20170222093421S
Control Version MiniPtz_V2.0.1_build201702091153
Web Page Version 1.1.1 Build 20170222
Plugin Version 2.0.3.47
 
Hi Guys, have the same issue with micro SD card on YC-110AR cam from Jack.
@vasycara - could you plz share this firmware somewere plz?

Right now I have these below:
Program Version V2.1.1 Build 20170222093421S
Control Version MiniPtz_V2.0.1_build201702091153
Web Page Version 1.1.1 Build 20170222
Plugin Version 2.0.3.47

The last firmware forV2 as of IPNC_S2l2._build20170314 is share by nikifon, and it's here, see # 23 you can download it.
For me this last firmware works perfectly, registers on sd card 24/7, does not restart.Upgrade at your own risk.
 
Thanks, upgrade completed :) . I'll let know if any issues will appears. Hope all will work fine...
 
With this firmware (IPNC_S2l2.1.1_build20170314122826.zip | Kernel flashed too) I have some problems with focus of the camera. It takes very long until picture is sharp and if I click on saved position button twice then it once more gets blurred and needs about 2 secs. to recover sharpness.
Sometimes it takes 3-5 seconds to focus.

Did this behaviour already occure to someone else?
 
It's definitely much worse than with previous firmware... also the total blurred image after clicking on a position button without actually moving as the camera already is on this position didn't occur.
And I didn't even notice the focus before, now it's annoying...
 
It's definitely much worse than with previous firmware... also the total blurred image after clicking on a position button without actually moving as the camera already is on this position didn't occur.
And I didn't even notice the focus before, now it's annoying...
For me miniptz Huisun goes fine with the latest firmware.
If you are not happy, take back the firmware that you had before.
 
Just tried this firmware, am having major problems, the PTZ controls on the webplugin are reversed, and the camera will no longer reach its maximum upward tilt :( Plus experiencing the pixilated focus issue mentioned above.
 
Just tried this firmware, am having major problems, the PTZ controls on the webplugin are reversed, and the camera will no longer reach its maximum upward tilt :( Plus experiencing the pixilated focus issue mentioned above.

How far up will it go? You may want to try Preset 95 and there may be an adjustment to activate additional upward tilt. I believe these default to zero degrees but can be manually set to allow up to -10 degrees...I suspect yours was set to -10 but has defaulted back to zero with the firmware update...

Not sure about the reversed PTZ controls. That's odd.
 
(Yes I had upgraded the Kernel + Firmware, Factory reset etc). Unfortunately I upgraded one cam it looked fine so I did another 10 at remote locations. I ended up getting a Chinese colleague to call Huisun, they provided a number of patch's which appear to work, I will do more testing today.
 
Yes I think the forum really needs a thread / table with known working version combinations,....once I et everything 100% I will put up what i'm using.
 
Any chance to get the password for achieved files ?
You don't need the zip password in order for the camera to be able to use the files - the camera firmware is able to open the files OK, it has the password built in.
But if you want to extract the files yourself for research / study - let me know and I can send you the password privately.
 
  • Like
Reactions: vasycara