Please confirm if I'm on the right track

T

TheE

Pulling my weight
Dec 8, 2018
170
107
TX
Here's our new setup so far (see picture). This is a dual NIC BI server.

The LAN will plug into the back of the server.

With the second port (separated), I will run a cable to Keystone 1 (red line in picture). Then using a patch cable, connect Keystone 1 to port 1 of POE switch (yellow line in picture).

1000002688.jpg

If the above is correct, my second question is about the NanoStation Loco M5 and it's POE adapter for cameras across the street.

Please see the wiring diagram picture. Where it shows "ToLAN." Is it correct that I need to plug the "ToLAN" into port 2 of the POE switch and the other run is for the antenna?

1000002689.jpg

Please let me know if you need any clarification, and thanks in advance for your time and help!
 
Last edited:
  • Like
Reactions: Flintstone61
looktall said:
Why would you not just plug the server directly into the switch?
Click to expand...


Guessing we could?? But was thinking the route I mentioned above to use the patch panel and to keep most of the wiring behind the hardware for a clean look. Thank you for your idea!
 
Yep, that LAN port from the Nano POE power supply will plug into any of the ports on your POE switch where your other cameras are plugged into and the terminal marked POE goes to the Nano.
Actually it does not draw any power from you POE switch as it (Nano) gets is power from that "so called" POE power supply.
You will need to provide POE to the remote cameras at that location (if needed) via another POE switch, wall warts, or injectors since the Nano does not pass power, only ethernet data.
 
Last edited:
  • Like
Reactions: TheE and JDreaming
Broachoski said:
Yep, that LAN port from the Nano POE power supply will plug into any of the ports on your POE switch where your other cameras are plugged into and the terminal marked POE goes to the Nano.
Actually it does not draw any power from you POE switch as it (Nano) gets is power from that "so called" POE power supply.
You will need to provide POE to the remote cameras at that location (if needed) via another POE switch, wall warts, or injectors since the Nano does not pass power, only ethernet data.
Click to expand...

Thank you for your time and info.

And yes, we have the equipment for across the street. Just need to complete our server infrastructure build. Then we'll hang this and start on the other side.

1000002690.jpg
 
  • Like
Reactions: Broachoski
While I understand the desire the have a "clean" install, adding the keystone panel/connectors for this use case just adds several extra points of failure (the keystone connector itself and a second patch cable) for absolutely no reason. Patch panels are normally used to terminate runs from other locations at a central location so that the tech can plug in only the runs that are actually needed at that time. In this case, you know you will always need to plug in that wire, so why triple the chances of failure?

They make 1u "brush" panels that you can use to clean up any wires coming from the back of the panel to the front of the panel. With some proper cable management, the "look" the brush panel provides can be exactly the same as a patch panel. However I would highly suggest this solution vs a patch panel for those wires because it removes two points of failure.

51LpMUpkSJL._AC_SL1200_.jpg

 
Last edited:
As an Amazon Associate IPCamTalk earns from qualifying purchases.
  • Like
Reactions: TheE, looney2ns, TonyR and 1 other person
The Automation Guy said:
While I understand the desire the have a "clean" install, adding the keystone panel/connectors for this use case just adds several extra points of failure (the keystone connector itself and a second patch cable) for absolutely no reason. Patch panels are normally used to terminate runs from other locations at a central location so that the tech can plug in only the runs that are actually needed at that time. In this case, you know you will always need to plug in that wire, so why triple the chances of failure?

They make 1u "brush" panels that you can use to clean up any wires coming from the back of the panel to the front of the panel. With some proper cable management, the "look" the brush panel provides can be exactly the same as a patch panel. However I would highly suggest this solution vs a patch panel for those wires because it removes two points of failure.

51LpMUpkSJL._AC_SL1200_.jpg

Click to expand...


Great explanation and makes good sense. Thank you for this input!
 
As an Amazon Associate IPCamTalk earns from qualifying purchases.
You must log in or register to reply here.
Top Bottom