SD59225U-HNI DH_SD-Eos_MultiLang_PN_Stream3_V2.800.0000000.5.R.190827
- Thread starter EMPIRETECANDY
- Start date
looney2ns
IPCT Contributor
Steveee
Pulling my weight
I have updated to this firmware, and now have no manual control of ptz functions from gdmss app.
It was working previously.
I don't know if I've inadvertently changed a setting on camera?
Any ideas please.
It was working previously.
I don't know if I've inadvertently changed a setting on camera?
Any ideas please.
Make a default after you update the firmware, if still not work, make a hard reset on the camera's reset button(Camera is powered on), hold it for 7-10seconds.
Steveee
Pulling my weight
Ok, I have tried:-
Ptz reset, default cam, factory default, reset switch on cam, re-boot, power on/ off, uninstall/ reinstall app.
Still no ptz control in gdmss pluss app. Also tried gdmss lite app, no go.
So tell me I'm an idiot for not doing the obvious(To Some) , but I'd really like to know what I'm missing?
Thanks.
Ptz reset, default cam, factory default, reset switch on cam, re-boot, power on/ off, uninstall/ reinstall app.
Still no ptz control in gdmss pluss app. Also tried gdmss lite app, no go.
So tell me I'm an idiot for not doing the obvious(To Some) , but I'd really like to know what I'm missing?
Thanks.
Steveee
Pulling my weight
I should of updated my post...
I have 1 SD-59430 that works just fine with this firmware and 1 that must of had a bad update. The PTZ controls are wacked out along with the presets.
This firmware has baseline 2 that does not allow you to downgrade below 2.800.XXX. There is nothing below 2.800.005. in the 2.800.xxx series, so it is stuck until I try a serial UART update or a new firmware is put out...
( I doubt there will be, I'm sure these are close to EOL) I did not have much luck with the TFTP option that I tried.
looney2ns
IPCT Contributor
Steveee
Pulling my weight
Yes,
But that was good timing, I've just got ptz control working from app OK again.
Found a setting on NVR for ptz(in with camera registration etc) for that channel was set to local, so set to remote and now works ok on app.
I had not noticed before.
I'm just glad its working again
But that was good timing, I've just got ptz control working from app OK again.
Found a setting on NVR for ptz(in with camera registration etc) for that channel was set to local, so set to remote and now works ok on app.
I had not noticed before.
I'm just glad its working again
Is there a different firmware i can drop back to?
This totaly killed my autotracking. It worked pretty well. Now it dont follow anything like its too slow.
Sent from my iPhone using Tapatalk
This totaly killed my autotracking. It worked pretty well. Now it dont follow anything like its too slow.
Sent from my iPhone using Tapatalk
Yes, we found some bug for the IVS /autotracking, will talk with dahua guys on Tuesday, they have 1 week holiday. We back to work tomorrow and process all the pending orders.
What are the most stable camera and PTZ firmware for the SD59430U right now? Does anyone have a source for a repository of older firmware versions for this camera?
It seems like Dahua makes excellent camera hardware but vastly needs to improve their firmware stability and testing before releasing new versions. I've run into countless issues and wasted untold hours trying different things to get things to work how it should have worked the first time out of the box.
There are a lot of little things I noticed with my SD59430U that drive me up a wall. First, the camera and PTZ firmware seem to need to be matched. If you update one and not the other you may or may not run into problems.
Second, Dahua seems to randomly add and take away features between revisions. As an example, older camera firmware versions list a bunch of statistics for the camera and PTZ while newer versions those statistics are gone. Another example is the audio bitrates for G.711A codec - older versions show 8k/16k/48k options and the new version only shows 8k. Why? I'm stuck using AAC or Mpeg2 Layer-2 if I want anything above 8K. (8k audio totally sucks, btw).
Third, restoring configuration backups made from older firmware versions may or may not work correctly when imported with newer firmware, which kind of defeats the whole purpose of making backups in the first place. I don't know how many times I've had to reprogram PTZ presets for fear of causing issues (severe stuttering, sluggishness, random freezes) when restoring an old backup with new firmware. It's like the programmers are too lazy to add some logical parsing to the incoming file to ignore values and settings that may be different or out of range for the new firmware. Importing a value that is out of range for the new firmware almost always causes issues due to this oversight.
Fourth, every single update needs the camera to be hard reset (factory default or reset button), then 'soft' reset to defaults to even begin to work correctly. Again, poor programming comes into play here because restoring a config backup may or may not work depending on how different the saved values are.
Fifth, the manual in-camera firmware checks almost always come back 'It is the latest version' on every Dahua device I own, even if they are a few revisions behind the latest version.
It seems like Dahua makes excellent camera hardware but vastly needs to improve their firmware stability and testing before releasing new versions. I've run into countless issues and wasted untold hours trying different things to get things to work how it should have worked the first time out of the box.
There are a lot of little things I noticed with my SD59430U that drive me up a wall. First, the camera and PTZ firmware seem to need to be matched. If you update one and not the other you may or may not run into problems.
Second, Dahua seems to randomly add and take away features between revisions. As an example, older camera firmware versions list a bunch of statistics for the camera and PTZ while newer versions those statistics are gone. Another example is the audio bitrates for G.711A codec - older versions show 8k/16k/48k options and the new version only shows 8k. Why? I'm stuck using AAC or Mpeg2 Layer-2 if I want anything above 8K. (8k audio totally sucks, btw).
Third, restoring configuration backups made from older firmware versions may or may not work correctly when imported with newer firmware, which kind of defeats the whole purpose of making backups in the first place. I don't know how many times I've had to reprogram PTZ presets for fear of causing issues (severe stuttering, sluggishness, random freezes) when restoring an old backup with new firmware. It's like the programmers are too lazy to add some logical parsing to the incoming file to ignore values and settings that may be different or out of range for the new firmware. Importing a value that is out of range for the new firmware almost always causes issues due to this oversight.
Fourth, every single update needs the camera to be hard reset (factory default or reset button), then 'soft' reset to defaults to even begin to work correctly. Again, poor programming comes into play here because restoring a config backup may or may not work depending on how different the saved values are.
Fifth, the manual in-camera firmware checks almost always come back 'It is the latest version' on every Dahua device I own, even if they are a few revisions behind the latest version.
Last edited:
maybe will help you
as NVR I use QNAP, for my "QNAP QVR Pro" only recognizes 13.R.181205
Hello, bought such a camera DH-SD59225U-HNI, the problem with auto track, 90% miss or loses goal, man this or cat or bird equally, firmware as I understand the latter, the problem in camera or mistake in firmware, that advise . Sorry about my English )
Type DH-SD59225U-HNI
System VersionV2.800.0000000.5.R.E4.2512.3S.NR, Build Date: 2019-08-27
WEB Version V3.2.1.780791
ONVIF Version18.12(V2.4.5.729857
VersionPTZ VersionV2.301.0000000.3.RHNT_180331_26657
View attachment reg_ch1_20191209162333_20191209162413_x264.m4v
Type DH-SD59225U-HNI
System VersionV2.800.0000000.5.R.E4.2512.3S.NR, Build Date: 2019-08-27
WEB Version V3.2.1.780791
ONVIF Version18.12(V2.4.5.729857
VersionPTZ VersionV2.301.0000000.3.RHNT_180331_26657
View attachment reg_ch1_20191209162333_20191209162413_x264.m4v
Last edited: