hello everyone, I'm new on here and have been playing around with ip cameras and blue iris software. that said i have been able to do most of the research already and had hit dead ends everywhere.
I recently purchased 4 "WiFi Smart Camera" i discovered that they are Shenzhen icomm with ANYKA processor. i need to flash the firmware and gain access to the ONVIF and RTSP ports, however i can not access the camera webpage to change any of the settings. the camera makes you use the Yi IoT app to setup the device via a cloud system. im trying to disable the cloud and put the camera on blue iris via RTSP
here is the log file from the camera i disassembled to find the chipset info.
[2023/11/19 12:56:18][cloud_demo.c: sync_time(): 2242] yi_sync_time ok!
get net info:ip: 192.168.1.xxx, mask: 255.255.255.0, route: 192.168.1.1, dns1: 192.168.1.1, dns2: 8.8.8.8
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1476 errors:0 dropped:0 overruns:0 frame:0
TX packets:1476 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:85689 (83.6 KiB) TX bytes:85689 (83.6 KiB)
wlan0 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX
inet addr:192.168.1.xxx Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:33 errors:0 dropped:2 overruns:0 frame:0
TX packets:19 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6274 (6.1 KiB) TX bytes:2811 (2.7 KiB)
wlan0 IEEE 802.11abgn ESSID:[Not For Your Eyes]
Mode:Managed Frequency:5.785 GHz Access Point: XX:XX:XX:XX:XX:XX
Bit Rate=30 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr
![Eek! :eek: :eek:](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
ff Fragment thr
![Eek! :eek: :eek:](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
ff
Encryption key
![Eek! :eek: :eek:](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
ff
Power Management
![Eek! :eek: :eek:](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
ff
Link Quality=70/70 Signal level=-27 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:3 Missed beacon:0
[global]
user = admin
secret = admin
dev_name = 小K互联网摄像机
soft_version = 2000
uid_name = danale.conf
[ethernet]
dhcp = 1
ipaddr = 192.168.1.xxx
netmask = 255.255.255.0
gateway = 192.168.1.1
firstdns = 8.8.8.8
backdns = 108.108.108.108
[wireless]
ssid = [Not For Your Eyes]
mode = Infra
security = 3
password = [Not For Your Eyes]
running = softap
[softap]
s_ssid =
s_password =
osd_name = AKWIPC0000000010
What you needis DeviceGateway app from hikvision which will install isup server. And then develop transmission protocol to suit your needs.
Easier way is just setting up a VPN to your home network and access cameras that way.