Network Cable Color Code

shaids

Young grasshopper
Joined
Sep 30, 2016
Messages
75
Reaction score
4
Hi

Was wondering what color codes do you guys use to connect NVR to IP Camera for Hikvision products. I have noticed when doing a general maintenance at customers sites which the IP cams were installed by other suppliers/installer use different color code matches not always but rarely.

This is probably a random post but i'm thinking some people don't use the codes which are explained by hikvision but use there own.

Lets hear it.. What color codes do you use for A & B points?

regards
 

TonyR

IPCT Contributor
Joined
Jul 15, 2014
Messages
16,443
Reaction score
38,162
Location
Alabama
You're referring to Cat-5 / Ethernet cabling for networking, right? If so, and it's to be straight-thru Ethernet, you can use either T-568A or T-568B as long as you use the same layout on BOTH ends. It seems that the majority of pre-made, straight-thru Ethernet patch cables I have purchased use the T-568B layout on both ends. For a crossover cable, use T-568A on one end and B on the other end.

I have memorized the layout for T-568B so I use that on both ends of the cable. So to clarify and re-enforce the image at the end of this reply, here are some conventions that I follow that you can adjust to suit yourself as long as the same wire color order is followed. For example, if you prefer to hold the cable in your right hand, just reverse the order of the colors from top to bottom but ALWAYS keep the RJ-45 crimp connector locking tang facing AWAY from you.

Assuming you already know how to prep the cable, insert, crimp and test and you asked only about color code, here goes:

With the RJ-45 connector in right hand, locking tang AWAY from you and cable entrance pointing toward the cable and with CAT-5 cable in left hand, arrange wires top to bottom as follows:

white/orange
orange
white/green
blue
white/blue
green
white/brown
brown

Cat5_T-568B.gif
 
Last edited:

zero-degrees

Known around here
Joined
Aug 15, 2015
Messages
1,359
Reaction score
847
^^^^^^ That!

You use anything else your an a** hole! People sometimes come along here and say "As long as it matches on both ends, blah blah blah". Using anything other than the standard is just doing the next guy that follows up behind you a disservice!
 

fenderman

Staff member
Joined
Mar 9, 2014
Messages
36,897
Reaction score
21,250
^^^^^^ That!

You use anything else your an a** hole! People sometimes come along here and say "As long as it matches on both ends, blah blah blah". Using anything other than the standard is just doing the next guy that follows up behind you a disservice!
its not just about the guy who follows you...if you dont use one of the standards you WILL have interference issues and it will not work properly, particularly on longer runs.
 

zero-degrees

Known around here
Joined
Aug 15, 2015
Messages
1,359
Reaction score
847
if you dont use one of the standards you WILL have interference
Very True, I started to type about the different twist patterns and over all length of different pairs and the issues it can cause at 100'+ but was being lazy and figured I was wasting my breath.
 

bp2008

Staff member
Joined
Mar 10, 2014
Messages
12,666
Reaction score
14,005
Location
USA
I may never know why the original designers didn't choose a more intuitive layout, where adjacent pins would always share a wire pair, but it is what it is. Follow T-568B and if you need to replace one end of a cable that isn't wired to this standard, you should probably chop off both ends and re-crimp the standard layout.

Ubiquiti toughcable connectors conveniently have the T-568B layout printed large on the box; that was a great help in memorizing it.
 

tigerwillow1

Known around here
Joined
Jul 18, 2016
Messages
3,815
Reaction score
8,424
Location
USA, Oregon
I may never know why the original designers didn't choose a more intuitive layout, where adjacent pins would always share a wire pair, but it is what it is.
Just a guess, since telephones use the 2 center pins of the RJ11/RJ14 for pair #1, and the pins outside of them for pair #2, maybe the RJ45 pinouts just followed that for compatibility purposes. The theory falls apart however if the 3-pair RJ25 is considered.
 

shaids

Young grasshopper
Joined
Sep 30, 2016
Messages
75
Reaction score
4
This is interesting to hear and am sure we all agree that we stick to what works. T-568B is what i use and have always been using. but as to what bp2008 said why not have a more intuitive layout which is unique for CCTV IP cams. Hmmmm, anyways lets see more random questions on this forum, it does help a lot of us to hear other or second opinion.
 

Securame

Pulling my weight
Joined
Mar 25, 2014
Messages
664
Reaction score
214
Location
Barcelona, Spain
This is interesting to hear and am sure we all agree that we stick to what works. T-568B is what i use and have always been using. but as to what bp2008 said why not have a more intuitive layout which is unique for CCTV IP cams. Hmmmm, anyways lets see more random questions on this forum, it does help a lot of us to hear other or second opinion.
Because CCTV IP cams are network devices, so the same guidelines that apply to any other network device/wiring apply to them. The same UTP wire that is used for an IP camera can be used for a computer, an IP phone, a router, or a networked toaster.
 

kteas1

n3wb
Joined
Nov 4, 2016
Messages
6
Reaction score
1
I use 568a, just because I have it memorized, but both are ok. A and B work equally well, just use the same configuration on both ends. Don't use any other method, as these are the best ways to cut interference. You don't want to run data on two pairs next to each other.

Sent from my SM-N910T using Tapatalk
 

alastairstevenson

Staff member
Joined
Oct 28, 2014
Messages
15,930
Reaction score
6,778
Location
Scotland
You don't want to run data on two pairs next to each other.
With apologies for the picky comment, but they are only not next to each other when they are in the RJ45 connector. And are running 10/100Mbps ethernet.
In the cable itself - it's the twists that reduce the common-mode signals.
 
Top