hmjgriffon
Known around here
I meant Looney, but cool
Dahua 2MP 25x Starlight IR PTZ Network Camera (SD49225T-HN)
- Thread starter ldasilva
- Start date
-
- Tags
- sd49225t-hn
Brian Martin
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 157
- Reaction score
- 72
This is not the junction box you wound use with a pole mount. This is used on flat structural surfaces.
Brian Martin
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 157
- Reaction score
- 72
Buck up and git er done.
TheSuperServer
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 143
- Reaction score
- 64
Please post a night video when you get a chance.
nayr
IPCT Contributor
seal these junction boxes and pipes up well, cant tell you how many times I open an external junction box and come face to face with a bunch of pissed off wasps..
hmjgriffon
Known around here
LOL good idea
Brian Martin
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 157
- Reaction score
- 72
They ain't getting in my boxes! All holes are plugged. Pun intended!
Thread sealant on 1/2 holeplugs, silicone and rubber seal on back of junction box and hole behind j box siliconed up!
looney2ns
IPCT Contributor
Yes I have, the grey junction box on the floor will mount on the pole behind the cam, and all connections will be made in it.
2 1/8" ID pole made for Directv dish's and the tripod is also made for Sat dishes. I think it will be fine. Pole is 40" long.
looney2ns
IPCT Contributor
Plumbers putty does a fine job of sealing up holes around wires. I've had the same wasp experience before.
TheSuperServer
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 143
- Reaction score
- 64
How best to mount this camera in this location? I'm thinking about using the pole mount angled a little where the arrow is. Any suggestions would be appreciated. I'm replacing those other cameras with this one ptz.
hmjgriffon
Known around here
Can't wait to see this go up, only reason I'm looking at a roof mount is because my roof is so low unless I get one of those parapet mounts it'll be in reaching distance, plus the dishes are already up there. I've also considered just putting a pole in the ground lol.
looney2ns
IPCT Contributor
I really HOPE I get it installed this coming week. Been itching to get er done.
hmjgriffon
Known around here
Yeah me too, I wanna play with it
looney2ns
IPCT Contributor
That will work if it gets the views you want from there.
How best to mount this camera in this location? I'm thinking about using the pole mount angled a little where the arrow is. Any suggestions would be appreciated. I'm replacing those other cameras with this one ptz.
gregbert
Getting the hang of it
Did you get both gaskets with the camera or did one come with the junction box?
I only got the one on the left (with the curved corners).
hmjgriffon
Known around here
I got the curved tube mount and it didn't come with any gasket heh. silicone makes a fine gasket though.
Solar Deity
Getting comfortable
I got the PFA120 for the SD599225U-HNI and it came with two gaskets for the interface between the corner mount, PFA151 and the wall mount, PFA110.
hmjgriffon
Known around here
is anyone running a newer fimware on the SD59225U-HNI than this? Just curious.
Brian Martin
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 157
- Reaction score
- 72
http://www1.dahuasecurity.com/download/Accessory_Selection_2017012354.pdfHow best to mount this camera in this location? I'm thinking about using the pole mount angled a little where the arrow is. Any suggestions would be appreciated. I'm replacing those other cameras with this one ptz.
Use the link to find your cam and mounting options.
You might be able to use a corner mount on that fascia board. Hard to tell but it looks like there may be enough room to clear and avoid the gutter. With a corner mount you could see the same direction of those other cakes and the side of the structure.
Brian Martin
Getting the hang of it
- Joined
- Jan 26, 2017
- Messages
- 157
- Reaction score
- 72
@nayr . How did you wire in the motion and gate sensor to work?Its march already, dont yeh think its about time to take down the xmas lights?
that looks like a nice vantage point, as long as your not trying to ID anyone up close..
I want to wire in two motion sensors so two presets are activated when each sensor is triggered.